Planar SIW leaky wave antenna with electronically reconfigurable E-and H-plane scanning

This paper reports on a novel technique of switching radiation characteristics electronically between E-and H-planes of planar Substrate Integrated Waveguide Leaky Wave Antennas (SIW-LWAs). The leaky wave mode is achieved through increasing the pitch of bounding metallic via posts on one side of SIW transmission section. The radiation switching is achieved by extending the top and bottom metallic planes to a distance of 1 mm along the leakage side. The extended section acts as a parallel plate section which is conveniently connected or disconnected from the leaking side of SIW through PIN diodes. The ‘ON’ state of PIN diodes extends the metal guides and results in the H-plane leakage whereas ‘OFF’ state of PIN diodes truncates the extended metal earlier and alter the leakage line boundary condition towards E-plane. The whole concept is validated by series of simulations followed by the realization and testing of the SIW-LWA. The measured radiation pattern scans about 54° in the E-plane between 10.0 GHz to 11.7 GHz, and 58° in the H-plane from 9 GHz to 10.6 GHz. The proposed topology is a suitable candidate for remote sensing and airborne applications

Review on fixed-frequency beam steering for leaky wave antenna

This paper aims to survey the efforts of researchers in response to the novel and effective technology of control radiation pattern at a fixed frequency for leaky wave antenna (LWA), map the research landscape from the literature onto coherent taxonomy and determine the basic properties of this potential field. In addition, this paper investigates the motivation behind using beam steering in LWA and the open challenges that impede the utility of this antenna design. This paper offers valuable recommendations to improve beam steering in LWA. The review revealed the development and improvement of several techniques of beam scanning LWA. However, several areas or aspects require further attention. All the articles, regardless of their research focus, attempt to address the challenges that impede the full utility of beam scanning and offer recommendations to mitigate their drawbacks. This paper contributes to this area of research by providing a detailed review of the available options and problems to allow other researchers and participants to further develop beam scanning. The new directions for this research are also described

Reconfigurable Leaky Wave Antenna based on Metamaterial Substrate Integrated Waveguide for 5G oriented beamsteering application

This work presents the study and the development of a Leaky Wave Antenna, based on a Composite Right-Left Handed transmission line and a Substrate Integrated Waveguide. The antenna system is designed to work in the frequency band of 26 GHz - 30 GHz, demonstrates beamsteering functionalities and a high gain. The conducted study is envisioned in the background of the fifth generation mobile networks (5G), in order to fulfil the requirements for the realization of a small cell antenna

Control Radiation Pattern for Half Width Microstrip Leaky Wave Antenna by Using PIN Diodes

In this paper, a novel design for single-layer half width microstrip leakywave antenna (HW-MLWA) is demonstrated. This model can be digitally control its radiation pattern at operation frequency and uses only two values of the bias voltage, with better impedance matching and insignificant gain variation. The scanning and controlling the radiation pattern of leaky-wave antennas (LWA) in steps at an operation frequency, by using switches PIN diodes, is investigated and a novel HW-MLWA is introduced. A control cell reconfigurable, that can be switched between two states, is the basic element of the antenna. The periodic LWA is molded by identical control cells where as a control radiation pattern is developed by combining numerous reconfigurable control cells. A gap capacitor is independently connected or disconnected in every unit cell by using a PIN diode switch to achieve fixedfrequency control radiation pattern scanning. The profile reactance at the free edge of (HW-MLWA) and thus the main lobe direction is altered by changing the states of the control cell. The antenna presented in this paper, can scan main beam between 18o to 44o at fixed frequency of 4.2 GHz with measured peak gain of 12.29 dBi

Through Wall Imaging Radar Antenna with a Focus on Opening New Research Avenues

This review paper is an effort to develop insight into the development in antennas for through wall imaging radar application. Review on literature on antennas for use in through wall imaging radar, fulfilling one or more requirements/specifications such as ultrawide bandwidth, stable and high gain, stable unidirectional radiation pattern, wide scanning angle, compactness ensuring portability and facilitating real-time efficient and simple imaging is presented. The review covers variants of Vivaldi, Bow tie, Horn, Spiral, Patch and Magneto-electric dipole antennas demonstrated as suitable antennas for the through wall imaging radar application. With an aim to open new research avenues for making better through wall imaging radar antenna, review on relevant compressive reflector antennas, surface integrated waveguide antennas, plasma antennas, metamaterial antennas and single frequency dynamically configurable meta-surface antennas are incorporated. The review paper brings out possibilities of designing an optimum through wall imaging radar antenna and prospects of future research on the antenna to improve radiation pattern and facilitate overall simple and efficient imaging by the through wall imaging radar

Overview on Multipattern and Multipolarization Antennas for Aerospace and Terrestrial Applications

In recent years, reconfigurable antennas, with the ability to radiate wave in more than one pattern and polarization, play a great role in modern telecommunication systems. Compared with conventional antennas, multipattern and multipolarization antennas have more advantages and better prospects. They can be used to improve system gain and security, satisfy system requirements, avoid noisy environment, and adapt to the environment flexibly. This paper discusses different patterns and polarizations of reconfigurable antennas according to current research work in this area. In the opinion of this paper, the radiation pattern states of antennas include beam direction, shape, and gain. The polarization states of antennas include horizontal/vertical linear, ±slant 45° linear, left-hand or right-hand circular polarized. Different multipattern and multipolarization antennas with various structures and working mechanisms are compared and discussed. Multipattern and multipolarization antennas have been well applied for aerospace and terrestrial applications, such as dynamic scenarios, adaptive beam scanning, and multiple-input-multiple-output (MIMO) systems

Analysis and design of new electronically reconfigurable periodic leaky-wave antennas

[SPA] El principal objetivo de la tesis es el estudio de nuevas tecnologías en el campo de las antenas reconfigurables. En particular, la tesis se centra en explorar y explotar el potencial que presentan un tipo de antenas denominadas como ¿Antenas basadas en Modos de Fuga¿ para controlar electrónicamente su diagrama de radiación. La tesis desarrolla el análisis, diseño y fabricación de tres novedosas antenas basadas en modos de fuga capaces de variar mediante unas pocas señales de control y de forma continua su ángulo de apuntamiento. El mecanismo de reconfiguración electrónica principalmente se basa en el control de la dispersión de los modos de fuga excitados en dichas estructuras, mediante un control electrónico introducido empleando estructuras periódicas resonantes combinadas con elementos activos tales como diodos varactores. La tesis demuestra claramente la utilidad de estas antenas en el campo de la reconfiguración electrónica, proponiendo estas nuevas estructuras como alternativas a otras soluciones más clásicas (como antenas en array de fase reconfigurables o reflectores parabólicos mecánicamente re-orientables mecánicamente) y otras de actualidad (como reflectarrays, transmitarrays, antenas metamateriales o antenas pixeladas), las cuales todas ellas presentan otros problemas en términos de coste, complejidad de diseño o limitaciones de escalabilidad en frecuencia, aportando así esta tesis novedosos conceptos de reconfiguración electrónica.[ENG] The thesis aims the design of novel reconfigurable antennas with electronic beam-scanning. In particular, the antennas analyzed are known as Fabry-Perot Antennas (FPA) and are currently of high interest in the scientific community because of their high-directivity, low-profile and structure simplicity, what allow them to be an interesting alternative to other technologies (e.g. parabolic reflectors, phased arrays, etc.) which require of complex power distribution networks, bulky external sources or costly techniques to achieve reconfigurable capabilities. In this thesis, the integration of active components, such as varactor diodes, with FPRA structures, is exploited to achieve electronic control of their aperture illumination, which in turn results in the electronic steering of the radiation-pattern main beam. A modal analysis based on the leaky-wave theory has allowed to understand and predict the behavior of these structures. An equivalent circuit model was developed to design and optimize the dimensions of theses complex structures, saving computational cost and time. The antennas are based on the control of the frequency dispersion response and the electromagnetic band-gap (EBG) properties of periodic structures, employing specially designed Frequency-Selective Surfaces (FSS) loaded with varactor diodes. Three novel antenna prototypes were manufactured to demonstrate electronic steering capability operating at 5.5GHz. Continuous scanning in elevation (1D scanning) and also in elevation and azimuth simultaneously (2D scanning) have been achieved employing just a few control signals (between 1 and 4 signals). The antenna structures have been implemented in a low-cost technology based on parallel plate waveguides and printed circuit boards which have allowed to design antennas with a reduced profile. Theoretical, simulated and experimental results are shown for each prototype to demonstrate the concepts. Also, some future lines related to novel planar reconfigurable antennas in development are also outlined. One of the main potential advantages of the reconfiguring principles presented for future applications is their frequency scalability. This would allow to apply these concepts to other technologies, such as MEMS or graphene, to build new reconfigurable antennas able to operate at higher frequency bands (e.g. mm-bands) for future applications.Universidad Politécnica de Cartagen

Antennas and Arrays for Mobile Platforms -- Direct Broadcast Satellite and Wireless Communication

Flexibility of any proposed communication links is becoming one of the most challenging features. Direct broadcasting satellite services, for example, will be greatly enhanced by providing service-on-the-move. This market is very demanding as it necessitates the development of a low cost, low profile antenna that can be mounted on top of SUVs and minivans, which is capable of continuously tracking the satellite. Another example is the wireless antennas for laptops and smart-phones, where the antennas should fit within an extremely small volume and should be capable of addressing many services over wide frequency range. In this dissertation, both DBS and the wireless antennas are addressed. In these studies, efforts have been concentrated in developing low profile planar antennas, in particular, slot arrays. Travelling wave slotted waveguide arrays have been utilized to minimize the scanning angle range limits due to their inherent beam tilt angle. CNC machines were utilized first to fabricate the early prototypes for sub-array developments. Subsequently, a low cost fabrication technology is adopted to develop a low cost and light weight full array using substrate integrated waveguides (SIWs). The SIW is fully characterized and an excellent equivalent model has been derived to allow easy translation of metallic waveguide components to SIW. Various SIW junctions, transitions, and arrays have been developed for array feed networks including a 64 radiating SIW full array and a 32 radiating SIW array with folded feed. Meanwhile, for the wireless antennas, the utilization of reconfigurable hardware has been introduced to provide the required multi-functionality services and wide frequency coverage. Various reconfigurable antennas were developed and utilized to demonstrate their advantages compared to other design options such as wide-band or multi-band approaches. Both micro-electro-mechanical switches MEMS and PIN diodes have been successfully utilized to switch between the different configurations. The placement, control, and modeling of the switches are also discussed and novel modeling and biasing topologies are introduced. A novel and practical concept of reconfigurable multiband antenna is introduced here too, where advantages of both the multi-band and the reconfigurable antenna structures can be simultaneously achieved while supporting more services

1-D broadside-radiating leaky-wave antenna based on a numerically synthesized impedance surface

A newly-developed deterministic numerical technique for the automated design of metasurface antennas is applied here for the first time to the design of a 1-D printed Leaky-Wave Antenna (LWA) for broadside radiation. The surface impedance synthesis process does not require any a priori knowledge on the impedance pattern, and starts from a mask constraint on the desired far-field and practical bounds on the unit cell impedance values. The designed reactance surface for broadside radiation exhibits a non conventional patterning; this highlights the merit of using an automated design process for a design well known to be challenging for analytical methods. The antenna is physically implemented with an array of metal strips with varying gap widths and simulation results show very good agreement with the predicted performance

Beam scanning by liquid-crystal biasing in a modified SIW structure

A fixed-frequency beam-scanning 1D antenna based on Liquid Crystals (LCs) is designed for application in 2D scanning with lateral alignment. The 2D array environment imposes full decoupling of adjacent 1D antennas, which often conflicts with the LC requirement of DC biasing: the proposed design accommodates both. The LC medium is placed inside a Substrate Integrated Waveguide (SIW) modified to work as a Groove Gap Waveguide, with radiating slots etched on the upper broad wall, that radiates as a Leaky-Wave Antenna (LWA). This allows effective application of the DC bias voltage needed for tuning the LCs. At the same time, the RF field remains laterally confined, enabling the possibility to lay several antennas in parallel and achieve 2D beam scanning. The design is validated by simulation employing the actual properties of a commercial LC medium