Fully-photonic digital radio over fibre for future super-broadband access network applications

This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel UniversityIn this thesis a Fully-Photonic DRoF (FP-DRoF) system is proposed for deploying of future super-broadband access networks. Digital Radio over Fibre (DRoF) is more independent of the fibre network impairments and the length of fibre than the ARoF link. In order for fully optical deployment of the signal conversion techniques in the FP-DRoF architecture, two key components an Analogue-to-Digital Converter (ADC) and a Digital-to-Analogue Converter (DAC)) for data conversion are designed and their performance are investigated whereas the physical functionality is evaluated. The system simulation results of the proposed pipelined Photonic ADC (PADC) show that the PADC has 10 GHz bandwidth around 60 GHz of sampling rate. Furthermore, by changing the bandwidth of the optical bandpass filter, switching to another band of sampling frequency provides optimised performance condition of the PADC. The PADC has low changes on the Effective Number of Bit (ENOB) response versus analogue RF input from 1 GHz up to 22 GHz for 60 GHz sampling frequency. The proposed 8-Bit pipelined PADC performance in terms of ENOB is evaluated at 60 Gigasample/s which is about 4.1. Recently, different methods have been reported by researchers to implement Photonic DACs (PDACs), but their aim was to convert digital electrical signals to the corresponding analogue signal by assisting the optical techniques. In this thesis, a Binary Weighted PDAC (BW-PDAC) is proposed. In this BW-PDAC, optical digital signals are fully optically converted to an analogue signal. The spurious free dynamic range at the output of the PDAC in a back-to-back deployment of the PADC and the PDAC was 26.6 dBc. For further improvement in the system performance, a 3R (Retiming, Reshaping and Reamplifying) regeneration system is proposed in this thesis. Simulation results show that for an ultrashort RZ pulse with a 5% duty cycle at 65 Gbit/s using the proposed 3R regeneration system on a link reduces rms timing jitter by 90% while the regenerated pulse eye opening height is improved by 65%. Finally, in this thesis the proposed FP-DRoF functionality is evaluated whereas its performance is investigated through a dedicated and shared fibre links. The simulation results show (in the case of low level signal to noise ratio, in comparison with ARoF through a dedicated fibre link) that the FP-DRoF has better BER performance than the ARoF in the order of 10-20. Furthermore, in order to realize a BER about 10-25 for the ARoF, the power penalty is about 4 dBm higher than the FP-DRoF link. The simulation results demonstrate that by considering 0.2 dB/km attenuation of a standard single mode fibre, the dedicated fibre length for the FP-DRoF link can be increased to about 20 km more than the ARoF link. Moreover, for performance assessment of the proposed FP-DRoF in a shared fibre link, the BER of the FP-DRoF link is about 10-10 magnitude less than the ARoF link for -19 dBm launched power into the fibre and the power penalty of the ARoF system is 10 dBm more than the FP-DRoF link. It is significant to increase the fibre link’s length of the FP-DRoF access network using common infrastructure. In addition, the simulation results are demonstrated that the FP-DRoF with non-uniform Wavelength Division Multiplexing (WDM) is more robust against four wave mixing impairment than the conventional WDM technique with uniform wavelength allocation and has better performance in terms of BER. It is clearly verified that the lunched power penalty at CS for DRoF link with uniform WDM techniques is about 2 dB higher than non-uniform WDM technique. Furthermore, uniform WDM method requires more bandwidth than non-uniform scheme which depends on the total number of channels and channels spacing

A jittered-sampling correction technique for ADCs

In Analogue to Digital Converters (ADCs) jittered sampling raises the noise floor; this leads to a decrease in its Signal to Noise ratio (SNR) and its effective number of bits (ENOB). This research studies a technique that compensate for the effects of sampling with a jittered clock. A thorough understanding of sampling in various data converters is complied

Pipelined photonic analog-to-digital converter

Electronic analog to digital converters (EADCs) face serious challenges when the root mean square timing jitter of the sampling pulse is less than a femtosecond. This restriction limits the maximum allowable sampling frequency of an EADC. In photonic analog-to-digital conversion (PADC), using a mode locked laser as a sampling source limits the sampling frequency timing jitter only at sub-femtosecond levels. The current architectures for PADC use photonic techniques either for sampling or for quantization. Consequently, current PADC architectures are not suitable for higher frequency applications because of the limitations of their electronic components. In this paper, the feasibility of implementing concept architecture for a fully photonic pipelined ADC is analyzed and evaluated to provide a design for an 8-bit pipelined PADC, the performance of which is investigated through modeling and simulation. The 8-bit pipelined PADC's effective number of bits is shown to be 4.34 bits at 200 gigasample per second

Plasmonic color filter array, high performance analog to digital converter architectures and novel circuit techniques

Part I: Plasmonic color filters can be manufactured at lower cost since they can be fabricated in single lithographic process step as compared to Fabry-Perot based filters. In addition, they have narrow passband making resolving sharp features in sample spectrum possible. Due to these benefits, in this thesis, Plasmonic color filters are investigated as alternative to conventional color filters and their feasibility for spectroscopy demonstrated through reconstruction of 6 sample spectra by using a set of 20 color filters. The error in reconstructed sample spectra is less than 0.137 root mean squared error across all samples. Part II: A novel 12-bit pipelined successive approximation analog to digital converter is investigated for high speed data conversion. The design was implemented in TSMC 65nm process to demonstrate the feasibility of the architecture. Furthermore, a high dynamic range audio delta sigma modulator using pseudo-pseudo differential topology was investigated and feasibility simulated using TSMC 65nm process. In addition, various novel systems and circuit techniques including efficient calibration of feedback digital to analog converters, new boosted switch and push-pull source follower circuits were investigated to improve upon existing circuit topologies

Digital Signal Processing Techniques Applied to Radio over Fiber Systems

The dissertation aims to analyze different Radio over Fiber systems for the front-haul applications. Particularly, analog radio over fiber (A-RoF) are simplest and suffer from nonlinearities, therefore, mitigating such nonlinearities through digital predistortion are studied. In particular for the long haul A-RoF links, direct digital predistortion technique (DPDT) is proposed which can be applied to reduce the impairments of A-RoF systems due to the combined effects of frequency chirp of the laser source and chromatic dispersion of the optical channel. Then, indirect learning architecture (ILA) based structures namely memory polynomial (MP), generalized memory polynomial (GMP) and decomposed vector rotation (DVR) models are employed to perform adaptive digital predistortion with low complexities. Distributed feedback (DFB) laser and vertical capacity surface emitting lasers (VCSELs) in combination with single mode/multi-mode fibers have been linearized with different quadrature amplitude modulation (QAM) formats for single and multichannel cases. Finally, a feedback adaptive DPD compensation is proposed. Then, there is still a possibility to exploit the other realizations of RoF namely digital radio over fiber (D-RoF) system where signal is digitized and transmits the digitized bit streams via digital optical communication links. The proposed solution is robust and immune to nonlinearities up-to 70 km of link length. Lastly, in light of disadvantages coming from A-RoF and D-RoF, it is still possible to take only the advantages from both methods and implement a more recent form knows as Sigma Delta Radio over Fiber (S-DRoF) system. Second Order Sigma Delta Modulator and Multi-stAge-noise-SHaping (MASH) based Sigma Delta Modulator are proposed. The workbench has been evaluated for 20 MHz LTE signal with 256 QAM modulation. Finally, The 6x2 GSa/s sigma delta modulators are realized on FPGA to show a real time demonstration of S-DRoF system. The demonstration shows that S-DRoF is a competitive competitor for 5G sub-6GHz band applications

High Temperature Silicon Carbide Mixed-signal Circuits for Integrated Control and Data Acquisition

Wide bandgap semiconductor materials such as gallium nitride (GaN) and silicon carbide have grown in popularity as a substrate for power devices for high temperature and high voltage applications over the last two decades. Recent research has been focused on the design of integrated circuits for protection and control in these wide bandgap materials. The ICs developed in SiC and GaN can not only complement the power devices in high voltage and high frequency applications, but can also be used for standalone high temperature control and data acquisition circuitry. This dissertation work aims to explore the possibilities in high temperature and wide bandgap circuit design by developing a host of mixed-signal circuits that can be used for control and data acquisition. These include a family of current-mode signal processing circuits, general purpose amplifiers and comparators, and 8-bit data converters. The signal processing circuits along with amplifiers and comparators are then used to develop an integrated mixed-signal controller for a DC-DC flyback converter in a microinverter application. The 8-bit SAR ADC and the 8-bit R-2R ladder DAC open up the possibility of a remote data acquisition and control system in high temperature environments. The circuits and systems presented here offer a gateway to great opportunities in high temperature and power electronics ICs in SiC

Energy autonomous systems : future trends in devices, technology, and systems

The rapid evolution of electronic devices since the beginning of the nanoelectronics era has brought about exceptional computational power in an ever shrinking system footprint. This has enabled among others the wealth of nomadic battery powered wireless systems (smart phones, mp3 players, GPS, …) that society currently enjoys. Emerging integration technologies enabling even smaller volumes and the associated increased functional density may bring about a new revolution in systems targeting wearable healthcare, wellness, lifestyle and industrial monitoring applications