51 research outputs found

    Pilot-aided estimation and equalisation of a Radio-over-Fibre system in Wideband Code Division Multiple Access

    Get PDF
    In this study, the impact of a Radio-over-Fibre (RoF) subsystem on the capacity performance of wideband code division multiple access is evaluated. This study investigates the use of pilot-aided channel estimation to compensate for the optical subsystem non-linearities for different channel conditions, estimation intervals and coding schemes. The results show that pilot-aided channel estimation is an effective method for compensating the composite impairments of the optical subsystem and the radio frequency (RF) channel. It is found that there is always a suitable pilot power level which maximises the system capacity performance regardless of coding scheme and channel condition. Also, the peak capacity is only slightly affected by a decrease in the estimation interval

    Signal Design and Machine Learning Assisted Nonlinearity Compensation for Coherent Optical Fibre Communication Links

    Get PDF
    This thesis investigates low-complexity digital signal processing (DSP) for signal design and nonlinearity compensation strategies to improve the performance of single-mode optical fibre links over different distance scales. The performance of a novel ML-assisted inverse regular perturbation technique that mitigates fibre nonlinearities was investigated numerically with a dual-polarization 64 quadrature amplitude modulation (QAM) link over 800 km distance. The model outperformed the heuristically-optimised digital backpropagation approach with <5 steps per span and mitigated the gain expansion issue, which limits the accuracy of an untrained model when the balance between the nonlinear and linear components becomes considerable. For short reach links, the phase noise due to low-cost, high-linewidth lasers is a more significant channel impairment. A novel constellation optimisation algorithm was, therefore, proposed to design modulation formats that are robust against both additive white Gaussian noise (AWGN) and the residual laser phase noise (i.e., after carrier phase estimation). Subsequently, these constellations were numerically validated in the context of a 400ZR standard system, and achieved up to 1.2 dB gains in comparison with the modulation formats which were optimised only for the AWGN channel. The thesis concludes by examining a joint strategy to modulate and demodulate signals in a partially-coherent AWGN (PCAWGN) channel. With a low-complexity PCAWGN demapper, 8- to 64-ary modulation formats were designed and validated through numerical simulations. The bit-wise achievable information rates (AIR) and post forward error correction (FEC) bit error rates (BER) of the designed constellations were numerically validated with: the theoretically optimum, Euclidean (conventional), and low-complexity PCAWGN demappers. The resulting constellations demonstrated post-FEC BER shaping gains of up to 2.59 dB and 2.19 dB versus uniform 64 QAM and 64-ary constellations shaped for the purely AWGN channel model, respectively. The described geometric shaping strategies can be used to either relax linewidth and/or carrier phase estimator requirements, or to increase signal-to-noise ratio (SNR) tolerance of a system in the presence of residual phase noise

    Digital Processing for an Analogue Subcarrier Multiplexed Mobile Fronthaul

    Get PDF
    In order to meet the demands of the fifth generation of mobile communication networks (5G), such as very high bit-rates, very low latency and massive machine connectivity, there is a need for a flexible, dynamic, scalable and versatile mobile fronthaul. Current industry fronthaul standards employing sampled radio waveforms for digital transport suffer from spectral inefficiency, making this type of transport impractical for the wide channel bandwidths and multi-antenna systems required by 5G. On the other hand, analogue transport does not suffer from these limitations. It is, however, prone to noise, non-linearity and poor dynamic range. When combined with analogue domain signal aggregation/multiplexing, it also lacks flexibility and scalability, especially at millimetre wave frequencies. Measurements (matched in simulation) of analogue transport at millimetre wave frequencies demonstrate some of these issues. High data rates are demonstrated employing wide bandwidth channels combined using traditional subcarrier multiplexing techniques. However, only a limited number of channels can be multiplexed in this manner, with poor spectral efficiency, as analogue filter limitations do not allow narrow gaps between channels. To this end, over the last few years, there has been significant investigation of analogue transport schemes combined with digital channel aggregation/ de-aggregation (combining/ separating multiple radio waveforms in the digital domain). This work explores such a technique. Digital processing is used at the transmitter to flexibly multiplex a large number of channels in a subcarrier multiplex, without the use of combiners, mixers/ up-converters or Hilbert transforms. Orthogonal Frequency Division Multiplexing (OFDM) - derived Discrete Multi-Tone (DMT) and Single Sideband (SSB) modulated channels are integrated within a single Inverse Fast Fourier Transform (IFFT) operation. Channels or channel groups are mapped systematically into Nyquist zones by using, for example, a single IFFT (for a single 5G mobile numerology) or multiple IFFTs (for multiple 5G mobile numerologies). The analogue transport signal generated in this manner is digitally filtered and band-pass sampled at the receiver such that each corresponding channel (e.g. channels destined to the same radio frequency (RF)/ millimetre wave (mmW) frequency) in the multiplex is presented at the same intermediate frequency, due to the mapping employed at the transmitter. Analogue or digital domain mixers/ down-converters are not required with this technique. Furthermore, each corresponding channel can be readily up-converted to their respective RF/mmW channels with minimal per-signal processing. Measurement results, matched in simulation, for large signal multiplexes with both generic and 5G mobile numerologies show error-vector magnitude performance well within specifications, validating the proposed system. For even larger multiplexes and/or multiplexes residing on a higher IF exceeding the analogue bandwidth and sampling rate specifications of the ADCs at the receiver, the use of a bandwidth-extension device is proposed to extend the mapping to a mapping hierarchy and relax the analogue bandwidth and sampling rate requirements of the ADCs. This allows the receiver to still use digital processing, with only minimal analogue processing, to band-pass sample smaller blocks of channels from the larger multiplex, down to the same intermediate frequency. This ensures that each block of channels is within the analogue bandwidth specification of the ADCs. Performance predictions via simulation (based on a system model matched to the measurements) show promising results for very large multiplexes and large channel bandwidths. The multiplexing technique presented in this work thus allows reductions in per-channel processing for heterogeneous networking (or multi-radio access technologies) and multi-antenna configurations. It also creates a re-configurable and adaptable system based on available processing resources, irrespective of changes to the number of channels and channel groups, channel bandwidths and modulation formats

    Modelling and performances assessment of OFDM and fast-OFDM wireless communication systems.

    Get PDF
    This thesis is mainly concerned with the design, modelling and performance assessment of modulation techniques for use in wireless communication systems. The work is divided, broadly in three areas; a multimode system proposal, an assessment of a new modulation scheme and a system optimisation technique. A multimode system architecture employing GSM and EDGE systems and an Orthogonal Frequency Division Multiplexing (OFDM) system is proposed. The OFDM system is designed to have similar frame structure, channel allocation and spectrum shape to those of the GSM and EDGE systems. The multimode system is evaluated under typical multipath fading environments specified for GSM/EDGE and adjacent-channel and co-channel interference. The results indicated that the proposed OFDM system can be perfectly integrated within the GSM/EDGE network core. Furthermore, a novel modulation technique is investigated. Fast-OFDM (FOFDM) is a variation of OFDM, which offers twice the bandwidth efficiency when compared to OFDM. However, the bandwidth efficiency only applies to one dimensional modulation schemes (BPSK or M-ASK). The suitability of FOFDM for wireless communications is assessed by studying its performance under receiver front-end distortions and multipath fading environments. The performance of the FOFDM system is compared with the performance of a similar OFDM system. The results indicated that under small distortion conditions, the performance of FOFDM and OFDM is comparable. Finally, the effect of interpolation filtering on OFDM systems in noise limited and interference limited environments is investigated. The aim of this study is to highlight that interference should be taken into consideration when designing systems for wireless communications. In addition, this study can be utilised in software defined radio schemes, offering optimised performance. Overall, this thesis presents work over a range of research areas, providing system proposals, modulation comparisons and system optimisation techniques that can be used by developers of future mobile systems

    Maximising Achievable Rates of Experimental Nonlinear Optical Fibre Transmission Systems

    Get PDF
    It is generally expected that the demand for digital data services will continue to grow, placing ever greater requirements on optical fibre networks which carry the bulk of digital data. Research to maximise achievable information rates (AIR) over fibre has led to increasing spectral efficiency, symbol rate and bandwidth use. All of these contribute to transmission impairments due to the nonlinear nature of the optical fibre. This thesis describes research performed to investigate the effects of nonlinear impair- ments on the AIRs of experimental optical fibre transmission. To maximise throughput, the entire available optical bandwidth should be filled with transmission channels. An investigation into large bandwidth transmission through the use of spectrally shaped amplified spontaneous emission noise (SS-ASE) was con- ducted. The enhanced Gaussian noise model is used to analytically describe this tech- nique, and SS-ASE was experimentally shown to provide a lower bound on the AIR. Nonlinear interference (NLI) was modelled from an inter-symbol interference (ISI) model to characterise the noise and was experimentally verified. This new understand- ing helps quantify potential gain available from nonlinearity mitigation. Multicore fibres offer an alternative route to improve AIR, and are susceptible to another noise source known as crosstalk. This inter-core crosstalk can be controlled by suitable design of the fibre, hence in the limiting case, NLI rather than crosstalk will limit AIR. Nonlinearity compensation was, for the first time, experimentally demon- strated in the presence of crosstalk in a homogeneous 7-core fibre and shown to provide an increase in AIR. The results of this thesis can be used to evaluate future transmission systems for maximising information rates. It was shown that experimentally, SS-ASE is a viable transmission tool to evaluate system performance, NLI can be characterised using an ISI model and nonlinearity mitigation is possible in MCF systems limited by crosstalk

    Review of Recent Trends

    Get PDF
    This work was partially supported by the European Regional Development Fund (FEDER), through the Regional Operational Programme of Centre (CENTRO 2020) of the Portugal 2020 framework, through projects SOCA (CENTRO-01-0145-FEDER-000010) and ORCIP (CENTRO-01-0145-FEDER-022141). Fernando P. Guiomar acknowledges a fellowship from “la Caixa” Foundation (ID100010434), code LCF/BQ/PR20/11770015. Houda Harkat acknowledges the financial support of the Programmatic Financing of the CTS R&D Unit (UIDP/00066/2020).MIMO-OFDM is a key technology and a strong candidate for 5G telecommunication systems. In the literature, there is no convenient survey study that rounds up all the necessary points to be investigated concerning such systems. The current deeper review paper inspects and interprets the state of the art and addresses several research axes related to MIMO-OFDM systems. Two topics have received special attention: MIMO waveforms and MIMO-OFDM channel estimation. The existing MIMO hardware and software innovations, in addition to the MIMO-OFDM equalization techniques, are discussed concisely. In the literature, only a few authors have discussed the MIMO channel estimation and modeling problems for a variety of MIMO systems. However, to the best of our knowledge, there has been until now no review paper specifically discussing the recent works concerning channel estimation and the equalization process for MIMO-OFDM systems. Hence, the current work focuses on analyzing the recently used algorithms in the field, which could be a rich reference for researchers. Moreover, some research perspectives are identified.publishersversionpublishe

    Contributions to channel modelling and performance estimation of HAPS-based communication systems regarding IEEE Std 802.16TM

    Get PDF
    New and future telecommunication networks are and will be broadband type. The existing terrestrial and space radio communication infrastructures might be supplemented by new wireless networks that make and will make use of aeronautics-technology. Our study/contribution is referring to radio communications based on radio stations aboard a stratospheric platform named, by ITU-R, HAPS (High Altitude Platform Station). These new networks have been proposed as an alternative technology within the ITU framework to provide various narrow/broadband communication services. With the possibility of having a payload for Telecommunications in an aircraft or a balloon (HAPS), it can be carried out radio communications to provide backbone connections on ground and to access to broadband points for ground terminals. The latest implies a complex radio network planning. Therefore, the radio coverage analysis at outdoors and indoors becomes an important issue on the design of new radio systems. In this doctoral thesis, the contribution is related to the HAPS application for terrestrial fixed broadband communications. HAPS was hypothesised as a quasi-static platform with height above ground at the so-called stratospheric layer. Latter contribution was fulfilled by approaching via simulations the outdoor-indoor coverage with a simple efficient computational model at downlink mode. This work was assessing the ITU-R recommendations at bands recognised for the HAPS-based networks. It was contemplated the possibility of operating around 2 GHz (1820 MHz, specifically) because this band is recognised as an alternative for HAPS networks that can provide IMT-2000 and IMT-Advanced services. The global broadband radio communication model was composed of three parts: transmitter, channel, and receiver. The transmitter and receiver parts were based on the specifications of the IEEE Std 802.16TM-2009 (with its respective digital transmission techniques for a robust-reliable link), and the channel was subjected to the analysis of radio modelling at the level of HAPS and terrestrial (outdoors plus indoors) parts. For the channel modelling was used the two-state characterisation (physical situations associated with the transmitted/received signals), the state-oriented channel modelling. One of the channel-state contemplated the environmental transmission situation defined by a direct path between transmitter and receiver, and the remaining one regarded the conditions of shadowing. These states were dependent on the elevation angle related to the ray-tracing analysis: within the propagation environment, it was considered that a representative portion of the total energy of the signal was received by a direct or diffracted wave, and the remaining power signal was coming by a specular wave, to last-mentioned waves (rays) were added the scattered and random rays that constituted the diffuse wave. At indoors case, the variations of the transmitted signal were also considering the following matters additionally: the building penetration, construction material, angle of incidence, floor height, position of terminal in the room, and indoor fading; also, these indoors radiocommunications presented different type of paths to reach the receiver: obscured LOS, no LOS (NLOS), and hard NLOS. The evaluation of the feasible performance for the HAPS-to-ground terminal was accomplished by means of thorough simulations. The outcomes of the experiment were presented in terms of BER vs. Eb/N0 plotting, getting significant positive conclusions for these kind of system as access network technology based on HAPS

    Algorithms and Subsystems for Next Generation Optical Networks

    Get PDF
    This thesis investigates algorithms and subsystems for digital coherent optical networks to alleviate system requirements and enable spectrally efficient systems. Spectral shaping of individual channel is investigated to mitigate backreflections in bi-directional Passive Optical Network (PON) enabling more than 1000 users operating at 10 Gbit/s. It is then shown that temporal delay skews, caused by misalignment in the coherent receiver, induce a large penalty for Nyquist filtered signals. An adaptive 4×4 equaliser is developed to compensate the imperfections dynamically. This is subsequently demonstrated experimentally with Polarisation Division Multiplexed (PDM) Quadrature Phase Shift Keying (QPSK) and 16-level Quadrature Amplitude Modulation (QAM). Furthermore, a modified blind equaliser is designed to adaptively compensate for unknown amount of Chromatic Dispersion (CD). The equaliser is demonstrated experimentally using 10.7 GBd PDM-QPSK transmission over 5,200 km. To simplify the computational complexity of the equalisers a multiplier free update scheme is explored in simulations. Optical frequency combs are investigated as phase and frequency synchronised sub- carrier sources for Dense Wavelength Division Multiplexing (DWDM) systems. The effect of phase synchronisation between sub-channels of a superchannel is examined in simulations without showing performance deviation when no additional optical or digital processing is applied. Afterwards, the transmission performance of two generation techniques implementing 400 Gbit/s superchannels, utilising PDM-16QAM, is evaluated. Although, the average performance of the two combs is identical subchannel fluctuations are observed due to uneven spectral profile. Carrier Phase Estimation (CPE) is explored for both single channel and superchannels systems. An equaliser interleaved with CPE, is explored for PDM-64QAM with minor improvement. Alternatively, Digital Coherence Enhancement (DCE) allowed the detection of 6 GBd PDM-64QAM with a 1.4 MHz linewidth laser, an order of magnitude improvement in linewidth tolerance. Finally, a joint CPE across a comb superchannel is demonstrated with a factor of 5 tolerance improvement

    Space-division Multiplexed Optical Transmission enabled by Advanced Digital Signal Processing

    Get PDF
    corecore