A photovoltaic integrated unified power quality conditioner with a 27-level inverter

Abstract This paper presents a Unified Power Quality Conditioner (UPQC) with a 27- level inverter based on an asymmetric H-bridge topology. Each phase of the inverter is composed of three H-bridges, supplied by three DC sources scaled in the power of three. The output of the multilevel inverter is connected directly to the point of common coupling (PCC) without the need to a transformer or a filter. The calculation of the Shunt Active Power filter (SAPF) compensation current is based on the generalized theory of synchronous frame (d-q theory) while the calculation of a series active filter voltage is based on Instantaneous Reactive Power (p-q theory). The control of the SAPF is achieved by using a closed loop vector control followed by a new multilevel modulation technique. In addition to the capability of harmonic elimination of both current and voltage drawn from the source, the UPQC can produce real and reactive power to feed the loads during prolonged voltage outages or source shortage.  The injection of real and reactive power depends on the state of charge (SOC) of batteries, the frequency of the system, real and reactive power of the load, and power factor at the point of PCC. The proposed UPQC strategy is simulated in MATLAB SIMULINK and the results has shown a significant improved in Total Harmonics Distortion (THD) of both the voltage and currents. 

Unbalanced and Reactive Load Compensation Using MMCC-Based SATCOMs With Third-Harmonic Injection

Modular multilevel cascaded converter-based STATCOMs are scalable to higher voltages without requiring a step-up transformer with multiple windings and can be realized using a low switching frequency, giving lower harmonic content and hence a reduced filtering requirement. The paper presents a new injection technique to extend the operating ranges of MMCC STATCOMs when used for negative sequence and reactive current compensation. A non-sinusoidal voltage or current containing a fundamental and its third harmonic component is injected to achieve phase cluster voltage balance. This technique reduces the maximum dc-link voltage for the star configuration, and the maximum converter phase circulating current for the Delta case, compared to applying only sinusoidal zero sequence components for mitigating the same degree of load unbalance. The analysis is confirmed experimentally, showing that the third harmonic injection can allow a significant improvement of STATCOM capability for simultaneous compensation of unbalanced load and reactive current

Grid integration of renewable power generation

This thesis considers the use of three-phase voltage and current source inverters as interfacing units for renewable power, specifically photovoltaic (PV) into the ac grid. This thesis presented two modulation strategies that offer the possibility of operating PV inverters in grid and islanding modes, with reduced switching losses. The first modulation strategy is for the voltage source inverter (VSI), and exploits 3rd harmonic injection with selective harmonic elimination (SHE) to improve performance at low and high modulation indices, where the traditional SHE implementation experiences difficulties due to pulse dropping. The simulations and experimentation presented show that the proposed SHE allows grid PV inverters to be operated with less than a 1kHz effective switching frequency per device. This is vital in power generation, especially in medium and high power applications. Pulse dropping is avoided as the proposed modified SHE spreads the switching angles over 90°, in addition increasing the modulation index. The second proposed modulation strategy, called direct regular sampled pulse width modulation (DRSPWM), is for the current source inverter (CSI). It exploits a combination of forced and natural commutation imposed by the co-existence of an insulated gate bipolar transistor in series with a diode in a three phase current source inverter, to determine device dwell times and switching sequence selection. The DRSPWM strategy reduces switching frequency per device in a CSI by suspending each phase for 60°, similar to VSI dead-band, thus low switching losses are expected. Other benefits include simple digital platform implementation and more flexible switching sequence selection and pulse placement than with space vector modulation. The validity of the DRSPWM is confirmed using simulations and experimentation. This thesis also presents a new dc current offset compensation technique used to facilitate islanding or grid operation of inverter based distributed generation, with a reduced number of interfacing transformers. The proposed technique will enable transformerless operation of all inverters within the solar farm, and uses only one power transformer at the point of common coupling. The validity of the presented modulation strategies and dc current offset compensation technique are substantiated using simulations and experimentation.This thesis considers the use of three-phase voltage and current source inverters as interfacing units for renewable power, specifically photovoltaic (PV) into the ac grid. This thesis presented two modulation strategies that offer the possibility of operating PV inverters in grid and islanding modes, with reduced switching losses. The first modulation strategy is for the voltage source inverter (VSI), and exploits 3rd harmonic injection with selective harmonic elimination (SHE) to improve performance at low and high modulation indices, where the traditional SHE implementation experiences difficulties due to pulse dropping. The simulations and experimentation presented show that the proposed SHE allows grid PV inverters to be operated with less than a 1kHz effective switching frequency per device. This is vital in power generation, especially in medium and high power applications. Pulse dropping is avoided as the proposed modified SHE spreads the switching angles over 90°, in addition increasing the modulation index. The second proposed modulation strategy, called direct regular sampled pulse width modulation (DRSPWM), is for the current source inverter (CSI). It exploits a combination of forced and natural commutation imposed by the co-existence of an insulated gate bipolar transistor in series with a diode in a three phase current source inverter, to determine device dwell times and switching sequence selection. The DRSPWM strategy reduces switching frequency per device in a CSI by suspending each phase for 60°, similar to VSI dead-band, thus low switching losses are expected. Other benefits include simple digital platform implementation and more flexible switching sequence selection and pulse placement than with space vector modulation. The validity of the DRSPWM is confirmed using simulations and experimentation. This thesis also presents a new dc current offset compensation technique used to facilitate islanding or grid operation of inverter based distributed generation, with a reduced number of interfacing transformers. The proposed technique will enable transformerless operation of all inverters within the solar farm, and uses only one power transformer at the point of common coupling. The validity of the presented modulation strategies and dc current offset compensation technique are substantiated using simulations and experimentation

Compensation of unbalanced low-voltage grids using a photovoltaic generation system with a dual four-leg, two-level inverter

In this paper, a grid-connected photovoltaic (PV) generation system is proposed with the purpose of providing support to low-voltage grids, namely through the elimination or attenuation of the grid imbalances. This compensation must consider the load types, which can be either linear or non-linear, and whether the reactive power and current harmonics generated by the non-linear loads need to be compensated in addition to the unbalanced active power. This must be well considered, since the compensation of all aspects requires oversized PV inverters. Thus, the different unbalanced compensation schemes are addressed. Several schemes for the generation of the inverter current references taking into consideration the compensation and load type are presented. For this PV generation system, a dual four-leg, two-level inverter is proposed. It provides full unbalanced compensation owing to the fourth leg of the inverter and also extends the AC voltage, which is important when this compensation is required. To control this inverter, a control scheme for the inverter that considers several compensation factors is proposed. A vector voltage modulator associated with the controller is another aspect that is addressed in the paper. This modulator considers the balance between the DC voltages of the inverters. Several compensation schemes are verified through computational tests. The results validate the effectiveness of the proposed PV generation system.info:eu-repo/semantics/publishedVersio

Cascaded Inverters for Grid-Connected Photovoltaic Systems

With the extraordinary market growth in grid-connected PV systems, there is increasing interests in grid-connected PV inverters. Focus has been placed on cheap, high-efficiency, and innovative inverter solutions, leading to a high diversity within the inverters and new system configurations. This dissertation chooses cascaded multilevel inverter topologies for grid-connected PV systems to reduce the cost and improve the efficiency. First, a single-phase cascaded H-bridge multilevel PV inverter is discussed. To maximize the solar energy extraction of each PV string, an individual maximum power point tracking (MPPT) control scheme is applied, which allows independent control of each dc-link voltage. A generalized nonactive power theory is applied to generate the reactive current reference. Within the inverter’s capability, the local consumption of reactive power is provided to realize power factor correction. Then, the modular cascaded H-bridge multilevel inverter is connected to a three-phase utility system and nine PV panels. Individual MPPT control is also applied to realize better utilization of PV modules. Also, mismatches between PV panels may introduce unbalanced power supplied to the three-phase grid-connected system. Thus, a modulation compensation scheme is applied to balance the three-phase grid current by injecting a zero sequence voltage. A modular cascaded multilevel inverter prototype has been built and tested in both the single-phase and three-phase PV system. Simulation and experimental results are presented to validate the proposed control schemes. The three-phase cascaded voltage source inverter (VSI), as another cascaded inverter topology, is also proposed for grid-connected PV applications. The equivalent model and average model of the three-phase cascaded VSI are established to realize the central control. In addition, the control scheme applied in the traditional three-phase two-level VSI is modified for this application. Simulation and experimental results are presented as well. The targets of reducing the cost and improving the overall efficiency of the PV inverters can be achieved by applying the cascaded PV inverters and the proposed control schemes

Photovoltaic Supplied T-Type Three- Phase Inverter with Harmonic Current Compensation Capability

In this paper, a T-Type grid-connected inverter with harmonic current compensation capability is proposed and studied for the on-grid photovoltaic (PV) systems. This idea is based on the modification of the existing photovoltaic inverter control algorithm with the adaptation of active power filter control algorithm. The grid-connected PV inverter has similar topology and control methods as that of the active power filter systems. However, such multifunctional inverters have not yet matured for commercial use and call for more research. In this work, a conventional phase locked-loop algorithm is used to determine the angular position of the synchronous reference of the grid voltages. PV power is estimated and fed into the control loop. Then, the measured currents at the load terminals are proceeded to obtain harmonic current components. The obtained control signals are used to drive the grid-connected T-Type inverter

Control and grid integration of MW-range wind and solar energy conversion systems

Solar-based energy generation has increased by more than ten times over the same period. In total, worldwide electrical energy consumption increased by approximately 6340 TWh from 2003 to 2013. To meet the challenges created by intermittent energy generation sources, grid operators have increasingly demanded more stringent technical requirements for the connection and operation of grid-connected intermittent energy systems, for instance concerning fault ride through capability, voltage and frequency support, and inertia emulation. Ongoing developments include new or improved high-voltage converters, power converters with higher power density, control systems to provide ride-through capability, implementation of redundancy schemes to provide more reliable generation systems, and the use of high-voltage direct current (HVdc) links for the connection of large off-shore intermittent energy systems

Modular Multilevel Cascaded Flying Capacitor STATCOM for Balanced and Unbalanced Load Compensation

Voltage and current unbalance are major problems in distribution networks, particularly with the integration of distributed generation systems. One way of mitigating these issues is by injecting negative sequence current into the distribution network using a Static Synchronous Compensator (STATCOM) which normally also regulates the voltage and power factor. The benefits of modularity and scalability offered by Modular Multilevel Cascaded Converters (MMCC) make them suitable for STATCOM application. A number of different types of MMCC may be used, classified according to the sub-module circuit topology used. Their performance features and operational ranges for unbalanced load compensation are evaluated and quantified in this research. This thesis investigates the use of both single star and single delta configured five-level Flying Capacitor (FC) converter MMCC based STATCOMs for unbalanced load compensation. A detailed study is carried out to compare this type of sub-module with several other types namely: half bridge, 3-L H-bridge and 3-L FC half bridge, and reveals the one best suited to STATCOM operation. With the choice of 5-L FC H-bridge as the sub-module for STATCOM operation, a detailed investigation is also performed to decide which pulse width modulation technique is the best. This was based on the assessment of total harmonic distortion, power loss, sub-module switch utilization and natural balancing of inner flying capacitors. Two new modulation techniques of swapped-carrier PWM (SC-PWM) along with phase disposed and phase shifted PWM (PS-PWM) are analyzed under these four performance metrics. A novel contribution of this research is the development of a new space vector modulation technique using an overlapping hexagon technique. This space vector strategy offers benefits of eliminating control complexity and improving waveform quality, unlike the case of multilevel space vector technique. The simulation and experimental results show that this method provides superior performance and is applicable for other MMCC sub-modules. Another contribution is the analysis and quantification of operating ranges of both single star and delta MMCCs in rating the cluster dc-link voltage (star) and current (delta) for unbalanced load compensation. A novel method of extending the operating capabilities of both configurations uses a third harmonic injection method. An experimental investigation validates the operating range extension compared to the pure sinusoidal zero sequence voltage and current injection. Also, the superiority of the single delta configured MMCC for unbalanced loading compensation is validated

Modulation for Cascaded Multilevel Converters in PV Applications with High Input Power Imbalance

Cascaded multilevel inverters, such as the cascaded H-Bridge (CHB) converter, are an attractive solution for multi-string photovoltaic (PV) systems, because they enable direct connection to the medium voltage grid and maximum power point tracking of multiple strings. As a challenge of the topology, the operation with high power imbalance in the strings is constrained by the over-modulation. This limitation is analyzed for sinusoidal modulation and the impact on the maximum power imbalance is demonstrated. For increasing the operating range with maximum power tracking in the strings, a discontinuous modulation with extended maximum power imbalance and reduced losses is proposed. The method is analyzed in terms of maximum power imbalance, efficiency and power quality. In addition, the method is validated on an experimental test bench