Design and Optimization of Photonics-Based Beamforming Networks for Ultra-Wide mmWave-Band Antenna Arrays

In this chapter, we review the worldwide progress referred to designing optical beamforming networks intended to the next-generation ultra-wideband millimeter-wave phased array antennas for incoming fifth-generation wireless systems, which in recent years is under the close attention of worldwide communication community. Following the tendency, we study in detail the design concepts below true-time-delay photonics beamforming networks based on switchable or continuously tunable control. Guided by them, we highlight our NI AWRDE CAD-based simulation experiments in the frequency range of 57–76 GHz on design of two 16-channel photonics beamforming networks using true-time-delay approach. In the first scheme of the known configuration, each channel includes laser, optical modulator, and 5-bit binary switchable chain of optical delay lines. The second scheme has an optimized configuration based on only 3-bit binary switchable chain of optical delay lines in each channel, all of which are driven by four lasers with wavelength division multiplexing and a common optical modulator. In the result, the novel structural and cost-efficient configuration of microwave-photonics beamforming network combining wavelength division multiplexing and true-time-delay techniques is proposed and investigated

Novel ring resonator-based integrated photonic beamformer for broadband phased array receive antennas - part I: design and performance analysis

A novel optical beamformer concept is introduced that can be used for seamless control of the reception angle in broadband wireless receivers employing a large phased array antenna (PAA). The core of this beamformer is an optical beamforming network (OBFN), using ring resonator-based broadband delays, and coherent optical combining. The electro-optical conversion is performed by means of single-sideband suppressed carrier modulation, employing a common laser, Mach-Zehnder modulators, and a common optical sideband filter after the OBFN. The unmodulated laser signal is then re-injected in order to perform balanced coherent optical detection, for the opto-electrical conversion. This scheme minimizes the requirements on the complexity of the OBFN, and has potential for compact realization by means of full integration on chip. The impact of the optical beamformer concept on the performance of the full receiver system is analyzed, by modeling the combination of the PAA and the beamformer as an equivalent two-port RF system. The results are illustrated by a numerical example of a PAA receiver for satellite TV reception, showing that—when properly designed—the beamformer hardly affects the sensitivity of the receiver

Design of Reconfigurable Multiple-Beam Array Feed Network Based on Millimeter-Wave Photonics Beamformers

In this chapter, elaborating the direction of designing photonics-based beamforming networks (BFN) for millimeter-wave (mmWave) antenna arrays, we review the worldwide progress referred to designing multiple-beam photonics BFN and highlight our last simulation results on design and optimization of millimeter-photonics-based matrix beamformers. In particular, we review the specialties of mmWave photonics technique in 5G mobile networks of Radio-over-Fiber (RoF) technology based on fiber-wireless architecture. In addition, the theoretical background of array antenna multiple-beam steering using ideal models of matrix-based phase shifters and time delay lines is presented including a general analysis of radiation pattern sensitivity to compare updated photonics beamforming networks produced on phase shifter or true-time delay approach. The principles and ways to optimized photonics BFN design are discussed based on the study of photonics BFN scheme including integrated 8×8 optical Butler matrix (OBM). All schemes are modeled using VPIphotonics Design Suite and MATLAB software tools. In the result of simulation experiments, the outcome is obtained that both the integrated optical Butler matrix itself and the BFN based on it possess an acceptable quality of beams formation in a particular 5G pico-cell

Automatic Tuning of Silicon Photonics Millimeter-Wave Transceivers Building Blocks

Today, continuously growing wireless traffic have guided the progress in the wireless communication systems. Now, evolution towards next generation (5G) wireless communication systems are actively researched to accommodate expanding future data traffic. As one of the most promising candidates, integrating photonic devices in to the existing wireless system is considered to improve the performance of the systems. Emerging silicon photonic integrated circuits lead this integration more practically, and open new possibilities to the future communication systems. In this dissertation, the development of the electrical wireless communication systems are briefly explained. Also, development of the microwave photonics and silicon photonics are described to understand the possibility of the hybrid SiP integrated wireless communication systems. A limitation of the current electrical wireless systems are addressed, and hybrid integrated mm-wave silicon photonic receiver, and silicon photonic beamforming transmitter are proposed and analyzed in system level. In the proposed mm-wave silicon photonic receiver has 4th order pole-zero silicon photonic filter in the system. Photonic devices are vulnerable to the process and temperature variations. It requires manual calibration, which is expensive, time consuming, and prone to human errors. Therefore, precise automatic calibration solution with modified silicon photonic filter structure is proposed and demonstrated. This dissertation demonstrates fully automatic tuning of silicon photonic all-pass filter (APF)-based pole/zero filters using a monitor-based tuning method that calibrates the initial response by controlling each pole and zero individually via micro-heaters. The proposed tuning approach calibrates severely degraded initial responses to the designed elliptic filter shapes and allows for automatic bandwidth and center frequency reconfiguration of these filters. This algorithm is demonstrated on 2nd- and 4th-order filters fabricated in a standard silicon photonics foundry process. After the initial calibration, only 300ms is required to reconfigure a filter to a different center frequency. Thermal crosstalk between the micro-heaters is investigated, with substrate thinning demonstrated to suppress this effect and reduce filter calibration to less than half of the original thick substrate times. This fully automatic tuning approach opens the possibility of employing silicon photonic filters in real communication systems. Also, in the proposed beamforming transmitter, true-time delay ring resonator based 1x4 beamforming network is imbedded. A proposed monitor-based tuning method compensates fabrication variations and thermal crosstalk by controlling micro-heaters individually using electrical monitors. The proposed tuning approach successfully demonstrated calibration of OBFN from severely degraded initial responses to well-defined group delay response required for the targeted radiating angle with a range of 60◦ (-30◦ to 30◦ ) in a linear beamforming antenna array. This algorithm is demonstrated on OBFN fabricated in a standard silicon photonics foundry process. The calibrated OBFN operates at 30GHz and provide 2GHz bandwidth. This fully automatic tuning approach opens the possibility of employing silicon OBFN in real wideband mm-wave wireless communication systems by providing robust operating solutions. All the proposed photonic circuits are implemented using the standard silicon photonic technologies, and resulted in several publications in IEEE/OSA Journals and Conferences