Electronic and photonic switching in the atm era

Broadband networks require high-capacity switches in order to properly manage large amounts of traffic fluxes. Electronic and photonic technologies are being used to achieve this objective both allowing different multiplexing and switching techniques. Focusing on the asynchronous transfer mode (ATM), the inherent different characteristics of electronics and photonics makes different architectures feasible. In this paper, different switching structures are described, several ATM switching architectures which have been recently implemented are presented and the implementation characteristics discussed. Three diverse points of view are given from the electronic research, the photonic research and the commercial switches. Although all the architectures where successfully tested, they should also follow different market requirements in order to be commercialised. The characteristics are presented and the architectures projected over them to evaluate their commercial capabilities.Peer ReviewedPostprint (published version

Architecture, design, and modeling of the OPSnet asynchronous optical packet switching node

An all-optical packet-switched network supporting multiple services represents a long-term goal for network operators and service providers alike. The EPSRC-funded OPSnet project partnership addresses this issue from device through to network architecture perspectives with the key objective of the design, development, and demonstration of a fully operational asynchronous optical packet switch (OPS) suitable for 100 Gb/s dense-wavelength-division multiplexing (DWDM) operation. The OPS is built around a novel buffer and control architecture that has been shown to be highly flexible and to offer the promise of fair and consistent packet delivery at high load conditions with full support for quality of service (QoS) based on differentiated services over generalized multiprotocol label switching

Design of Routers for Optical Burst Switched Networks

Optical Burst Switching (OBS) is an experimental network technology that enables the construction of very high capacity routers using optical data paths and electronic control. In this dissertation, we study the design of network components that are needed to build an OBS network. Specifically, we study the design of the switches that form the optical data path through the network. An OBS network that switches data across wavelength channels requires wave-length converting switches to construct an OBS router. We study one particular design of wavelength converting switches that uses tunable lasers and wavelength grating routers. This design is interesting because wavelength grating routers are passive devices and are much less complex and hence less expensive than optical crossbars. We show how the routing problem for these switches can be formulated as a combinatorial puzzle or game, in which the design of the game board determines key performance characteristics of the switch. In this disertation, we use this formu-lation to facilitate the design of switches and associated routing strategies with good performance. We then introduce time sliced optical burst switching (TSOBS), a variant of OBS that switches data in the time domain rather that the wavelength domain. This eliminates the need for wavelength converters, the largest single cost component of systems that switch in the wavelength domain. We study the performance of TSOBS networks and discuss various design issues. One of the main components that is needed to build a TSOBS router is an optical time slot interchanger (OTSI). We explore various design options for OTSIs. Finally, we discuss the issues involved in the design of network interfaces that transmit the data from hosts that use legacy protocols into a TSOBS network. Ag-gregation and load balancing are the main issues that determine the performance of a TSOBS network and we develop and evaluate methods for both

Knockout packet loss probability analysis of SCWP optical packet switching wavelength distributed knockout architecture

The deployment of Optical Packet Switching (OPS) in Dense Wavelength Division Multiplexing (DWDM) backbone networks is perceived as a medium term promising alternative. Scalability restrictions imply that conventional switching architectures are unfeasible in this large-scale scenario. In a previous paper, the wavelength-distributed knockout architecture was proposed as a cost-effective scaling strategy for OPS switching fabrics. In this paper, this growable architecture is applied to OPS switching fabrics able to emulate output buffering. We also propose an scheduling algorithm which provides optimum performance if knockout packet losses are made negligible. The mathematical analysis to evaluate the knockout packet loss probability of this architecture is obtained, under uniform and non-uniform traffic patterns. To complement the switch dimensioning process, an upper bound assuring 0-knockout packet losses is compared with the exact analytical results.This research has been funded by Spanish MCyT grants TEC2004-05622-C04-01/TCM (CAPITAL) and TEC2004-05622-C04-02/TCM (ARPaq) and Xunta de Galicia grant PGIDIT04TIC322003PR

Future benefits and applications of intelligent on-board processing to VSAT services

The trends and roles of VSAT services in the year 2010 time frame are examined based on an overall network and service model for that period. An estimate of the VSAT traffic is then made and the service and general network requirements are identified. In order to accommodate these traffic needs, four satellite VSAT architectures based on the use of fixed or scanning multibeam antennas in conjunction with IF switching or onboard regeneration and baseband processing are suggested. The performance of each of these architectures is assessed and the key enabling technologies are identified