Quality of service differentiation for multimedia delivery in wireless LANs

Delivering multimedia content to heterogeneous devices over a variable networking environment while maintaining high quality levels involves many technical challenges. The research reported in this thesis presents a solution for Quality of Service (QoS)-based service differentiation when delivering multimedia content over the wireless LANs. This thesis has three major contributions outlined below: 1. A Model-based Bandwidth Estimation algorithm (MBE), which estimates the available bandwidth based on novel TCP and UDP throughput models over IEEE 802.11 WLANs. MBE has been modelled, implemented, and tested through simulations and real life testing. In comparison with other bandwidth estimation techniques, MBE shows better performance in terms of error rate, overhead, and loss. 2. An intelligent Prioritized Adaptive Scheme (iPAS), which provides QoS service differentiation for multimedia delivery in wireless networks. iPAS assigns dynamic priorities to various streams and determines their bandwidth share by employing a probabilistic approach-which makes use of stereotypes. The total bandwidth to be allocated is estimated using MBE. The priority level of individual stream is variable and dependent on stream-related characteristics and delivery QoS parameters. iPAS can be deployed seamlessly over the original IEEE 802.11 protocols and can be included in the IEEE 802.21 framework in order to optimize the control signal communication. iPAS has been modelled, implemented, and evaluated via simulations. The results demonstrate that iPAS achieves better performance than the equal channel access mechanism over IEEE 802.11 DCF and a service differentiation scheme on top of IEEE 802.11e EDCA, in terms of fairness, throughput, delay, loss, and estimated PSNR. Additionally, both objective and subjective video quality assessment have been performed using a prototype system. 3. A QoS-based Downlink/Uplink Fairness Scheme, which uses the stereotypes-based structure to balance the QoS parameters (i.e. throughput, delay, and loss) between downlink and uplink VoIP traffic. The proposed scheme has been modelled and tested through simulations. The results show that, in comparison with other downlink/uplink fairness-oriented solutions, the proposed scheme performs better in terms of VoIP capacity and fairness level between downlink and uplink traffic

Designs for the Quality of Service Support in Low-Energy Wireless Sensor Network Protocols

A Wireless Sensor Network (WSN) consists of small, low cost, and low energy sensor nodes that cooperatively monitor physical quantities, control actuators, and perform data processing tasks. A network may consist of thousands of randomly deployed self-configurable nodes that operate autonomously to form a multihop topology. This Thesis focuses on Quality of Service (QoS) in low-energy WSNs that aim at several years operation time with small batteries. As a WSN may include both critical and non-critical control and monitoring applications, QoS is needed to make intelligent, content specific trade-offs between energy and network performance. The main research problem is defining and implementing QoS with constrained energy budget, processing power, communication bandwidth, and data and program memories. The problem is approached via protocol designs and algorithms. These are verified with simulations and with measurements in practical deployments. This Thesis defines QoS for WSNs with quantifiable metrics to allow measuring and managing the network performance. The definition is used as a basis for QoS routing protocol and Medium Access Control (MAC) schemes, comprising dynamic capacity allocation algorithm and QoS support layer. Dynamic capacity allocation is targeted at reservation based MACs, whereas the QoS support layer operates on contention based MACs. Instead of optimizing the protocols for a certain use case, the protocols allow configurable QoS based on application specific requirements. Finally, this Thesis designs sensor self-diagnostics and diagnostics analysis tool for verifying network performance. Compared to the related proposals on in-network sensor diagnostics, the diagnostics also detects performance problems and identifies reasons for the issues thus allowing the correction of problems. The results show that the developed protocols allow a clear trade-off between energy, latency, throughput, and reliability aspects of QoS while incurring a minimal overhead. The feasibility of results for extremely resource constrained WSNs is verified with the practical implementation with a prototype hardware platform having only few Million Instructions Per Second (MIPS) of processing power and less than a hundred kBs data and program memories. The results of this Thesis can be used in the WSN research, development, and implementation in general. The developed QoS definition, protocols, and diagnostics tools can be used separately or adapted to other applications and protocols

Energy Efficient and Cooperative Solutions for Next-Generation Wireless Networks

Energy efficiency is increasingly important for next-generation wireless systems due to the limited battery resources of mobile clients. While fourth generation cellular standards emphasize low client battery consumption, existing techniques do not explicitly focus on reducing power that is consumed when a client is actively communicating with the network. Based on high data rate demands of modern multimedia applications, active mode power consumption is expected to become a critical consideration for the development and deployment of future wireless technologies. Another reason for focusing more attention on energy efficient studies is given by the relatively slow progress in battery technology and the growing quality of service requirements of multimedia applications. The disproportion between demanded and available battery capacity is becoming especially significant for small-scale mobile client devices, where wireless power consumption dominates within the total device power budget. To compensate for this growing gap, aggressive improvements in all aspects of wireless system design are necessary. Recent work in this area indicates that joint link adaptation and resource allocation techniques optimizing energy efficient metrics can provide a considerable gain in client power consumption. Consequently, it is crucial to adapt state-of-the-art energy efficient approaches for practical use, as well as to illustrate the pros and cons associated with applying power-bandwidth optimization to improve client energy efficiency and develop insights for future research in this area. This constitutes the first objective of the present research. Together with energy efficiency, next-generation cellular technologies are emphasizing stronger support for heterogeneous multimedia applications. Since the integration of diverse services within a single radio platform is expected to result in higher operator profits and, at the same time, reduce network management expenses, intensive research efforts have been invested into design principles of such networks. However, as wireless resources are limited and shared by clients, service integration may become challenging. A key element in such systems is the packet scheduler, which typically helps ensure that the individual quality of service requirements of wireless clients are satisfied. In contrastingly different distributed wireless environments, random multiple access protocols are beginning to provide mechanisms for statistical quality of service assurance. However, there is currently a lack of comprehensive analytical frameworks which allow reliable control of the quality of service parameters for both cellular and local area networks. Providing such frameworks is therefore the second objective of this thesis. Additionally, the study addresses the simultaneous operation of a cellular and a local area network in spectrally intense metropolitan deployments and solves some related problems. Further improving the performance of battery-driven mobile clients, cooperative communications are sought as a promising and practical concept. In particular, they are capable of mitigating the negative effects of fading in a wireless channel and are thus expected to enhance next-generation cellular networks in terms of client spectral and energy efficiencies. At the cell edges or in areas missing any supportive relaying infrastructure, client-based cooperative techniques are becoming even more important. As such, a mobile client with poor channel quality may take advantage of neighboring clients which would relay data on its behalf. The key idea behind the concept of client relay is to provide flexible and distributed control over cooperative communications by the wireless clients themselves. By contrast to fully centralized control, this is expected to minimize overhead protocol signaling and hence ensure simpler implementation. Compared to infrastructure relay, client relay will also be cheaper to deploy. Developing the novel concept of client relay, proposing simple and feasible cooperation protocols, and analyzing the basic trade-offs behind client relay functionality become the third objective of this research. Envisioning the evolution of cellular technologies beyond their fourth generation, it appears important to study a wireless network capable of supporting machine-to-machine applications. Recent standardization documents cover a plethora of machine-to-machine use cases, as they also outline the respective technical requirements and features according to the application or network environment. As follows from this activity, a smart grid is one of the primary machine-to-machine use cases that involves meters autonomously reporting usage and alarm information to the grid infrastructure to help reduce operational cost, as well as regulate a customer's utility usage. The preliminary analysis of the reference smart grid scenario indicates weak system architecture components. For instance, the large population of machine-to-machine devices may connect nearly simultaneously to the wireless infrastructure and, consequently, suffer from excessive network entry delays. Another concern is the performance of cell-edge machine-to-machine devices with weak wireless links. Therefore, mitigating the above architecture vulnerabilities and improving the performance of future smart grid deployments is the fourth objective of this thesis. Summarizing, this thesis is generally aimed at the improvement of energy efficient properties of mobile devices in next-generation wireless networks. The related research also embraces a novel cooperation technique where clients may assist each other to increase per-client and network-wide performance. Applying the proposed solutions, the operation time of mobile clients without recharging may be increased dramatically. Our approach incorporates both analytical and simulation components to evaluate complex interactions between the studied objectives. It brings important conclusions about energy efficient and cooperative client behaviors, which is crucial for further development of wireless communications technologies

Frequency Rendezvous and Physical Layer Network Coding for Distributed Wireless Networks

In this thesis, a transmission frequency rendezvous approach for secondary users deployed in decentralized dynamic spectrum access networks is proposed. Frequency rendezvous is a critical step in bootstrapping a wireless network that does not possess centralized control. Current techniques for enabling frequency rendezvous in decentralized dynamic spectrum access networks either require pre-existing infrastructure or use one of several simplifying assumptions regarding the architecture, such as the use of regularly spaced frequency channels for communications. Our proposed approach is designed to be operated in a strictly decentralized wireless networking environment, where no centralized control is present and the spectrum does not possess pre-defined channels. In our proposed rendezvous algorithm, the most important step is pilot tone detection and receiver query. In order to realize a shortest search time for the target receiver, an efficient scanning rule should be employed. In this thesis, three scanning rules are proposed and evaluated, namely: frequency sequence scanning, pilot tone strength scanning, and cluster scanning. To validate our result, we test our scanning rules with actual paging band spectrum measurements. Previous research on security of network coding focuses on the protection of data dissemination procedures and the detection of malicious activities such as pollusion attacks. The capabilities of network coding to detect other attacks has not been fully explored. In this thesis, a new mechanism based on physical layer network coding to detect wormhole attacks is proposed. When two signal sequences collide at the receiver, the difference between the two received sequences is determined by its distances to the senders. Therefore, by comparing the differences between the received sequences at two nodes, we can estimate the distance between them and detect those fake neighbor connections through wormholes. While the basic idea is clear, we design many schemes at both physical and network layers to turn the idea into a practical approach. Simulations using BPSK modulation at the physical layer show that the wireless nodes can effectively detect fake neighbor connections without the adoption of any special hardware on them

AN EFFICIENT COMBINED CONGESTION HANDLING=--A--cN-:cD~-­ ROUTE MAINTENANCE PROTOCOL FOR DYNAMIC ENVIRONMENT IN BLUETOOTH NETWORK

Bluetooth IS a widespread technology for small wireless networks that permits Bluetooth devices to construct a multi-hop network called a scatternet. A large number of connections passing through a single master/ bridge device may create the problem of congestion in a Bluetooth scatternet. In addition, routing in a multi-hop dynamic Bluetooth network, where a number of masters and bridges exist, sometimes creates technical hitches in a scatternet. It has been observed that frequent link disconnections and a new route construction consume more system resources that ultimately degrade the performance of the whole network. As, Bluetooth specification has defined piconet configuration, scatternet configuration has still not been standardized. The main objective of this thesis is to provide an efficient combined protocol for scatternet congestion handling and route maintenance. The methodology contains three parts

Contributions to IEEE 802.11-based long range communications

The most essential part of the Internet of Things (IoT) infrastructure is the wireless communication system that acts as a bridge for the delivery of data and control messages between the connected things and the Internet. Since the conception of the IoT, a large number of promising applications and technologies have been developed, which will change different aspects in our daily life. However, the existing wireless technologies lack the ability to support a huge amount of data exchange from many battery-driven devices, spread over a wide area. In order to support the IoT paradigm, IEEE 802.11ah is an Internet of Things enabling technology, where the efficient management of thousands of devices is a key function. This is one of the most promising and appealing standards, which aims to bridge the gap between traditional mobile networks and the demands of the IoT. To this aim, IEEE 802.11ah provides the Restricted Access Window (RAW) mechanism, which reduces contention by enabling transmissions for small groups of stations. Optimal grouping of RAW stations requires an evaluation of many possible configurations. In this thesis, we first discuss the main PHY and MAC layer amendments proposed for IEEE 802.11ah. Furthermore, we investigate the operability of IEEE 802.11ah as a backhaul link to connect devices over possibly long distances. Additionally, we compare the aforementioned standard with previous notable IEEE 802.11 amendments (i.e. IEEE 802.11n and IEEE 802.11ac) in terms of throughput (with and without frame aggregation) by utilizing the most robust modulation schemes. The results show an improved performance of IEEE 802.11ah (in terms of power received at long range while experiencing different packet error rates) as compared to previous IEEE 802.11 standards. Additionally, we expose the capabilities of future IEEE 802.11ah in supporting different IoT applications. In addition, we provide a brief overview of the technology contenders that are competing to cover the IoT communications framework. Numerical results are presented showing how the future IEEE 802.11ah specification offers the features required by IoT communications, thus putting forward IEEE 802.11ah as a technology to cater the needs of the Internet of Things paradigm. Finally, we propose an analytical model (named e-model) that provides an evaluation of the RAW onfiguration performance, allowing a fast adaptation of RAW grouping policies, in accordance to varying channel conditions. We base the e-model in known saturation models, which we adapted to include the IEEE 802.11ah’s PHY and MAC layer modifications and to support different bit rate and packet sizes. As a proof of concept, we use the proposed model to compare the performance of different grouping strategies,showing that the e-model is a useful analysis tool in RAW-enabled scenarios. We validate the model with existing IEEE 802.11ah implementation for ns-3.La clave del concepto Internet de las cosas (IoT) es que utiliza un sistema de comunicación inalámbrica, el cual actúa como puente para la entrega de datos y mensajes de control entre las "cosas" conectadas y el Internet. Desde la concepción del IoT, se han desarrollado gran cantidad de aplicaciones y tecnologías prometedoras que cambiarán distintos aspectos de nuestra vida diaria.Sin embargo, las tecnologías de redes computacionales inalámbricas existentes carecen de la capacidad de soportar las características del IoT, como las grandes cantidades de envío y recepción de datos desde múltiples dispositivos distribuidos en un área amplia, donde los dispositivos IoT funcionan con baterías. Para respaldar el paradigma del IoT, IEEE 802.11ah, la cual es una tecnología habilitadora del Internet de las cosas, para el cual la gestión eficiente de miles de dispositivos es una función clave. IEEE 802.11ah es uno de los estándares más prometedores y atractivos, desde su concepción orientada para IoT, su objetivo principal es cerrar la brecha entre las redes móviles tradicionales y la demandada por el IoT. Con este objetivo en mente, IEEE 802.11ah incluye entre sus características especificas el mecanismo de ventana de acceso restringido (RAW, por sus siglas en ingles), el cual define un nuevo período de acceso al canal libre de contención, reduciendo la misma al permitir transmisiones para pequeños grupos de estaciones. Nótese que para obtener una agrupación óptima de estaciones RAW, se requiere una evaluación de las distintas configuraciones posibles. En esta tesis, primero discutimos las principales mejoras de las capas PHY y MAC propuestas para IEEE 802.11ah. Además, investigamos la operatividad de IEEE 802.11ah como enlace de backhaul para conectar dispositivos a distancias largas. También, comparamos el estándar antes mencionado con las notables especificaciones IEEE 802.11 anteriores (es decir, IEEE 802.11n y IEEE 802.11ac), en términos de rendimiento (incluyendo y excluyendo la agregación de tramas de datos) y utilizando los esquemas de modulación más robustos. Los resultados muestran mejores resultados en cuanto al rendimiento de IEEE 802.11ah (en términos de potencia recibida a largo alcance, mientras se experimentan diferentes tasas de error de paquetes de datos) en comparación con los estándares IEEE 802.11 anteriores.Además, exponemos las capacidades de IEEE 802.11ah para admitir diferentes aplicaciones de IoT. A su vez, proporcionamos una descripción general de los competidores tecnológicos, los cuales contienden para cubrir el marco de comunicaciones IoT. También se presentan resultados numéricos que muestran cómo la especificación IEEE 802.11ah ofrece las características requeridas por las comunicaciones IoT, presentando así a IEEE 802.11ah como una tecnología que puede satisfacer las necesidades del paradigma de Internet de las cosas.Finalmente, proponemos un modelo analítico (denominado e-model) que proporciona una evaluación del rendimiento utilizando la característica RAW con múltiples configuraciones, el cual permite una rápida adaptación de las políticas de agrupación RAW, de acuerdo con las diferentes condiciones del canal de comunicación. Basamos el e-model en modelos de saturación conocidos, que adaptamos para incluir las modificaciones de la capa MAC y PHY de IEEE 802.11ah y para poder admitir diferentes velocidades de transmisión de datos y tamaños de paquetes. Como prueba de concepto, utilizamos el modelo propuesto para comparar el desempeño de diferentes estrategias de agrupación, mostrando que el e-model es una herramienta de análisis útil en escenarios habilitados para RAW. Cabe mencionar que también validamos el modelo con la implementación IEEE 802.11ah existente para ns-3

Device Discovery in Frequency Hopping Wireless Ad Hoc Networks

This research develops a method for efficient discovery of wireless devices for a frequency hopping spread spectrum, synchronous, ad hoc network comprised of clustered sub-networks. The Bluetooth wireless protocol serves as the reference protocol. The development of a discovery, or outreach, method for scatternets requires the characterization of performance metrics of Bluetooth piconets, many of which are unavailable in literature. Precise analytical models characterizing the interference caused to Bluetooth network traffic by inquiring devices, the probability mass function of packet error rates between arbitrary pairs of Bluetooth networks, and Bluetooth discovery time distribution are developed. Based on the characterized performance metrics, three scatternet outreach methods are developed and compared. Outreach methods which actively inquire on a regular basis, as proposed in literature, are shown to produce lower goodput, have greater mean packet delay, require more power, and cause significant delays in discovery. By passively remaining available for outreach, each of these disadvantages is avoided

Toward Open and Programmable Wireless Network Edge

Increasingly, the last hop connecting users to their enterprise and home networks is wireless. Wireless is becoming ubiquitous not only in homes and enterprises but in public venues such as coffee shops, hospitals, and airports. However, most of the publicly and privately available wireless networks are proprietary and closed in operation. Also, there is little effort from industries to move forward on a path to greater openness for the requirement of innovation. Therefore, we believe it is the domain of university researchers to enable innovation through openness. In this thesis work, we introduce and defines the importance of open framework in addressing the complexity of the wireless network. The Software Defined Network (SDN) framework has emerged as a popular solution for the data center network. However, the promise of the SDN framework is to make the network open, flexible and programmable. In order to deliver on the promise, SDN must work for all users and across all networks, both wired and wireless. Therefore, we proposed to create new modules and APIs to extend the standard SDN framework all the way to the end-devices (i.e., mobile devices, APs). Thus, we want to provide an extensible and programmable abstraction of the wireless network as part of the current SDN-based solution. In this thesis work, we design and develop a framework, weSDN (wireless extension of SDN), that extends the SDN control capability all the way to the end devices to support client-network interaction capabilities and new services. weSDN enables the control-plane of wireless networks to be extended to mobile devices and allows for top-level decisions to be made from an SDN controller with knowledge of the network as a whole, rather than device centric configurations. In addition, weSDN easily obtains user application information, as well as the ability to monitor and control application flows dynamically. Based on the weSDN framework, we demonstrate new services such as application-aware traffic management, WLAN virtualization, and security management