A 0.1–5.0 GHz flexible SDR receiver with digitally assisted calibration in 65 nm CMOS

© 2017 Elsevier Ltd. All rights reserved.A 0.1–5.0 GHz flexible software-defined radio (SDR) receiver with digitally assisted calibration is presented, employing a zero-IF/low-IF reconfigurable architecture for both wideband and narrowband applications. The receiver composes of a main-path based on a current-mode mixer for low noise, a high linearity sub-path based on a voltage-mode passive mixer for out-of-band rejection, and a harmonic rejection (HR) path with vector gain calibration. A dual feedback LNA with “8” shape nested inductor structure, a cascode inverter-based TCA with miller feedback compensation, and a class-AB full differential Op-Amp with Miller feed-forward compensation and QFG technique are proposed. Digitally assisted calibration methods for HR, IIP2 and image rejection (IR) are presented to maintain high performance over PVT variations. The presented receiver is implemented in 65 nm CMOS with 5.4 mm2 core area, consuming 9.6–47.4 mA current under 1.2 V supply. The receiver main path is measured with +5 dB m/+5dBm IB-IIP3/OB-IIP3 and +61dBm IIP2. The sub-path achieves +10 dB m/+18dBm IB-IIP3/OB-IIP3 and +62dBm IIP2, as well as 10 dB RF filtering rejection at 10 MHz offset. The HR-path reaches +13 dB m/+14dBm IB-IIP3/OB-IIP3 and 62/66 dB 3rd/5th-order harmonic rejection with 30–40 dB improvement by the calibration. The measured sensitivity satisfies the requirements of DVB-H, LTE, 802.11 g, and ZigBee.Peer reviewedFinal Accepted Versio

Multi-standard RF front-end for avionic systems

Aerodynamic issues such as drag, weight and aeroacoustic noise are important factors in evaluating the impact of a given antenna on an aircraft’s overall performance. These factors are directly related to aircraft fuel consumption, speed and range. This project’s focus is on RF front-end electronics. The main goal here is to bring aircraft radio equipment as close as possible to the antennas in order to minimize wiring weight and complexity. This calls for a drastic volume reduction of the radio equipment. To this end, the system level requirements for the RF front-ends in terms of frequency bandwidths, data rates, etc, are first investigated in order to identify applications where the proposed volume reductions are the most beneficial and feasible. Following this, the focus was on an architectural investigation of alternative topologies that can meet the specification. For each topology considered the front-end-level specification need to be translated to circuit/component level requirements. For each case, performance, cost and technical risk analyses are carried out. Then, the design and prototyping of key RF front-end circuits for the selected architecture are undertaken. The multilayered Low Temperature Co-fired Ceramic (LTCC) technology had to be considered as a high risk but more advantageous option in terms of volume/weight reduction. Finally, we aimed at integrating and testing the proposed RF front-end chain, first by characterizing each component individually, and then as a whole front-end subsystem

Subsampling receivers with applications to software defined radio systems

Este trabajo de tesis propone la utilización sistemas basados en submuestreo como una alternativa para la implementación de la etapa de down-conversion de los receptores de radio frecuencia (RF) empleados para aplicaciones multi-estándar y SDR (Software Defined Radio). El objetivo principal será el de optimizar el diseño en cuanto a flexibilidad y simplicidad, las cuales son propiedades inherentes en los sistemas basados en submuestreo. Por tanto, como reducir el número de componentes al mínimo es clave cuando un mismo receptor procesa diferentes estándares de comunicación, las arquitecturas basadas en submuestreo han sido seleccionadas, donde la reusabilidad de los componentes empleados es posible, así como la reducción de los costes totales de los receptores de comunicación y de los equipos de certificación que emplean estas arquitecturas. Un motivo adicional por el que los sistemas basados en submuestreo han sido seleccionados es el concerniente a la topología del receptor. Como la idea de la tecnología SDR es implementar todas las funcionalidades del receptor (filtrado, amplificación) en el dominio digital, el convertidores analógico-digital (ADC) deberá estar localizado en la cadena de recepción lo más cerca posible a la antena, siendo el objetivo final el convertir la señal directamente de RF a digital. Sin embargo, con los actuales ADC no es posible implementar esta idea debido al alto ancho de banda que necesitarían sin perder resolución para cubrir las especificaciones de los estándares de comunicaciones inalámbricas. Por tanto, los sistemas basados en submuestreo se presentan como la opción más adecuada para implementar este tipo de sistemas debido a que pueden muestrear la señal de entrada por debajo de la tasa de Nyquist, si se cumplen ciertas restricciones en cuanto a la elección de la frecuencia de muestreo. De este modo, los requerimientos del ADC serán relajados ya que, usando estas arquitecturas, este componente procesará la señal a frecuencias intermedias. Una vez se han introducido los conceptos principales de las técnicas de submuestreo, esta tesis doctoral presenta el diseño de una tarjeta de adquisición de datos basada en submuestreo con la finalidad de ser implementada como un receptor de test y certificación de banda ancha. El sistema propuesto proporciona una alta resolución para un elevado ancho de banda, a partir del uso de un S&H de bajo jitter y de un convertidor analógico digital ADC que trabaja a frecuencias intermedias. El sistema es implementado usando dispositivos comerciales en una placa de circuito impreso diseñada y fabricada, y cuya caracterización experimental muestra una resolución de más 8 bits para un ancho de banda analógico de 20 MHz. Concretamente, la resolución medida será mayor de 9 bits hasta una frecuencia de entrada de 2.9 GHz y mayor de 8 bits para una frecuencia de entrada de hasta 6.5 GHz, lo cual resulta suficiente para cubrir los requerimientos de la mayor parte de los actuales estándares de comunicaciones inalámbricas (GPS, GSM, GPRS, UMTS, Bluetooth, Wi-Fi, WiMAX). Sin embargo, los receptores basados en submuestreo presentan algunos importantes inconvenientes, como son adicionales fuentes de ruido (jitter y plegado de ruido térmico) y una dificultad añadida para implementarlo en escenarios multi-banda y no lineales. Acerca del plegado de ruido en la banda de interés, esta tesis propone el uso de una técnica basada en una arquitectura de reloj múltiple con el objetivo de aumentar la resolución y cubrir un número mayor de estándares para su test y certificación. Empleando una frecuencia de muestreo mayor para el caso del S&H, se conseguirá reducir este efecto, aumentando la resolución en aproximadamente 0.5-1 bit respecto al caso de sólo usar una fuente de reloj. Las expresiones teóricas de esta mejora son desarrolladas y presentadas en esta tesis, siendo posteriormente corroboradas de modo experimental. Por otra parte, esta tesis también propone novedosas técnicas para la aplicación de estos sistemas de submuestreo en entornos multi-banda y no lineales, los cuales presentan desafíos adicionales por el hecho de existir la posibilidad de solapamiento entre la señal de interés y los otros canales de comunicación, así como de solapamiento con sus armónicos. De este modo, esta tesis extiende el uso de los sistemas basados en submuestreo para este tipo de entornos, proponiendo técnicas para la elección de la frecuencia óptima de muestreo que evitan el solapamiento entre señales, a la vez que consiguen incrementar la resolución del receptor. Finalmente, se presentará la optimización en cuanto a características de ruido de un receptor concreto para aplicaciones de banda dual en entornos no lineales. Dicho receptor estará basado en las técnicas de reloj múltiple presentadas anteriormente y en una estructura de multi-filtro entre el S&H y el ADC. El sistema diseñado podrá emplearse para diversas aplicaciones a ambos lados de la cadena de comunicación, tal como en receptores de detección de espectro para radio cognitiva, o implementando el bucle de realimentación de un transmisor para la linealización de amplificadores de potencia. Por tanto, la presente tesis doctoral cuenta con tres contribuciones diferenciadas. La primera de ellas es la dedicada al diseño de un prototipo de recepción multi-estándar basado en submuestreo para aplicaciones de test y certificación. La segunda aportación es la dedicada a la optimización de las especificaciones de ruido a partir de las técnicas presentadas basadas en reloj múltiple. Por último, la tercera contribución principal es la relacionada con la extensión de este tipo de técnicas a sistemas multi-banda en entornos no lineales. Todas estas contribuciones han sido estudiadas teóricamente y experimentalmente validadas

Parametric analog signal amplification applied to nanoscale cmos wireless digital transceivers

Thesis presented in partial fulfillment of the requirements for the degree of Doctor of Philosophy in the subject of Electrical and Computer Engineering by the Universidade Nova de Lisboa,Faculdade de Ciências e TecnologiaSignal amplification is required in almost every analog electronic system. However noise is also present, thus imposing limits to the overall circuit performance, e.g., on the sensitivity of the radio transceiver. This drawback has triggered a major research on the field, which has been producing several solutions to achieve amplification with minimum added noise. During the Fifties, an interesting out of mainstream path was followed which was based on variable reactance instead of resistance based amplifiers. The principle of these parametric circuits permits to achieve low noise amplifiers since the controlled variations of pure reactance elements is intrinsically noiseless. The amplification is based on a mixing effect which enables energy transfer from an AC pump source to other related signal frequencies. While the first implementations of these type of amplifiers were already available at that time, the discrete-time version only became visible more recently. This discrete-time version is a promising technique since it is well adapted to the mainstream nanoscale CMOS technology. The technique itself is based on the principle of changing the surface potential of the MOS device while maintaining the transistor gate in a floating state. In order words, the voltage amplification is achieved by changing the capacitance value while maintaining the total charge unchanged during an amplification phase. Since a parametric amplifier is not intrinsically dependent on the transconductance of the MOS transistor, it does not directly suffer from the intrinsic transconductance MOS gain issues verified in nanoscale MOS technologies. As a consequence, open-loop and opamp free structures can further emerge with this additional contribution. This thesis is dedicated to the analysis of parametric amplification with special emphasis on the MOS discrete-time implementation. The use of the latter is supported on the presentation of several circuits where the MOS Parametric Amplifier cell is well suited: small gain amplifier, comparator, discrete-time mixer and filter, and ADC. Relatively to the latter, a high speed time-interleaved pipeline ADC prototype is implemented in a,standard 130 nm CMOS digital technology from United Microelectronics Corporation (UMC). The ADC is fully based on parametric MOS amplification which means that one could achieve a compact and MOS-only implementation. Furthermore, any high speed opamp has not been used in the signal path, being all the amplification steps implemented with open-loop parametric MOS amplifiers. To the author’s knowledge, this is first reported pipeline ADC that extensively used the parametric amplification concept.Fundação para a Ciência e Tecnologia through the projects SPEED, LEADER and IMPAC

CMOS ASIC Design of Multi-frequency Multi-constellation GNSS Front-ends

With the emergence of the new global navigation satellite systems (GNSSs) such as Galileo, COMPASS and GLONASS, the US Global Positioning System (GPS) has new competitors. This multiplicity of constellations will offer new services and a much better satellite coverage. Public regulated service (PRS) is one of these new services that Galileo, the first global positioning service under civilian control, will offers. The PRS is a proprietary encrypted navigation designed to be more reliable and robust against jamming and provides premium quality in terms of position and timing and continuity of service, but it requires the use of FEs with extended capabilities. The project that this thesis starts from, aims to develop a dual frequency (E1 and E6) PRS receiver with a focus on a solution for professional applications that combines affordability and robustness. To limit the production cost, the choice of a monolithic design in a multi-purpose 0.18 µm complementary metal-oxide-semiconductor (CMOS) technology have been selected, and to reduce the susceptibility to interference, the targeted receiver is composed of two independent FEs. The first ASIC described here is such FEs bundle. Each FE is composed of a radio frequency (RF) chain that includes a low-noise amplifier (LNA), a quadrature mixer, a frequency synthesizer (FS), two intermediate frequency (IF) filters, two variable-gain amplifiers (VGAs) and two 6-bit flash analog-to-digital converters (ADCs). Each have an IF bandwidth of 50 MHz to accommodate the wide-band PRS signals. The FE achieves a 30 dB of dynamic gain control at each channel. The complete receivers occupies a die area of 11.5 mm2 while consuming 115 mW from a supply of a 1.8 V. The second ASIC that targets civilian applications, is a reconfigurable single-channel FE that permits to exploit the interoperability among GNSSs. The FE can operate in two modes: a ¿narrow-band mode¿, dedicated to Beidou-B1 with an IF bandwidth of 8 MHz, and a ¿wide-band mode¿ with an IF bandwidth of 23 MHz, which can accommodate simultaneous reception of Beidou-B1/GPS-L1/Galileo-E1. These two modes consumes respectively 22.85 mA and 28.45 mA from a 1.8 V supply. Developed with the best linearity in mind, the FE shows very good linearity with an input-referred 1 dB compression point (IP1dB) of better than -27.6 dBm. The FE gain is stepwise flexible from 39 dB and to a maximum of 58 dB. The complete FE occupies a die area of only 2.6 mm2 in a 0.18 µm CMOS. To also accommodate the wide-band PRS signals in the IF section of the FE, a highly selective wide-tuning-range 4th-order Gm-C elliptic low-pass filter is used. It features an innovative continuous tuning circuit that adjusts the bias current of the Gm cell¿s input stage to control the cutoff frequency. With this circuit, the power consumption is proportional to the cutoff frequency thus the power efficiency is achieved while keeping the linearity near constant. Thanks to a Gm switching technique, which permit to keep the signal path switchless, the filter shows an extended tuning of the cutoff frequency that covers continuously a range from 7.4 MHz to 27.4 MHz. Moreover the abrupt roll-off of up to 66 dB/octave, can mitigate out-of-band interference. The filter consumes 2.1 mA and 7.5 mA at its lowest and highest cutoff frequencies respectively, and its active area occupies, 0.23 mm2. It achieves a high input-referred third-order intercept point (IIP3) of up to -1.3 dBVRMS

High Performance LNAs and Mixers for Direct Conversion Receivers in BiCMOS and CMOS Technologies

The trend in cellular chipset design today is to incorporate support for a larger number of frequency bands for each new chipset generation. If the chipset also supports receiver diversity two low noise amplifiers (LNAs) are required for each frequency band. This is however associated with an increase of off-chip components, i.e. matching components for the LNA inputs, as well as complex routing of the RF input signals. If balanced LNAs are implemented the routing complexity is further increased. The first presented work in this thesis is a novel multiband low noise single ended LNA and mixer architecture. The mixer has a novel feedback loop suppressing both second order distortion as well as DC-offset. The performance, verified by Monte Carlo simulations, is sufficient for a WCDMA application. The second presented work is a single ended multiband LNA with programmable integrated matching. The LNA is connected to an on-chip tunable balun generating differential RF signals for a differential mixer. The combination of the narrow band input matching and narrow band balun of the presented LNA is beneficial for suppressing third harmonic downconversion of a WLAN interferer. The single ended architecture has great advantages regarding PCB routing of the RF input signals but is on the other hand more sensitive to common mode interferers, e.g. ground, supply and substrate noise. An analysis of direct conversion receiver requirements is presented together with an overview of different LNA and mixer architectures in both BiCMOS and CMOS technology

Radiofrequency architectures and technologies for software defined radio

Six-port network is an interesting radiofrequency architecture with multiple possibilities. Since it was firstly introduced in the seventies as an alternative network analyzer, the six-port network has been used for many applications, such as homodyne receivers, radar systems, direction of arrival estimation, UWB (Ultra-Wide-Band), or MIMO (Multiple Input Multiple Output) systems. Currently, it is considered as a one of the best candidates to implement a Software Defined Radio (SDR). This thesis comprises an exhaustive study of this promising architecture, where its fundamentals and the state-of-the-art are also included. In addition, the design and development of a SDR 0.3-6 GHz six-port receiver prototype is presented in this thesis, which is implemented in conventional technology. The system is experimentally characterized and validated for RF signal demodulation with good performance. The analysis of the six-port architecture is complemented by a theoretical and experimental comparison with other radiofrequency architectures suitable for SDR. Some novel contributions are introduced in the present thesis. Such novelties are in the direction of the highly topical issues on six-port technique: development and optimization of real-time I-Q regeneration techniques for multiport networks; and search of new techniques and technologies to contribute to the miniaturization of the six-port architecture. In particular, the novel contributions of this thesis can be summarized as: - Introduction of a new real-time auto-calibration method for multiport receivers, particularly suitable for broadband designs and high data rate applications. - Introduction of a new direct baseband I-Q regeneration technique for five-port receivers. - Contribution to the miniaturization of six-port receivers by the use of the multilayer LTCC (Low Temperature Cofired Ceramic) technology. Implementation of a compact (30x30x1.25 mm) broadband (0.3-6 GHz) six-port receiver in LTTC technology. The results and conclusions derived from this thesis have been satisfactory, and quite fruitful in terms of publications. A total of fourteen works have been published, considering international journals and conferences, and national conferences. Aditionally, a paper has been submitted to an internationally recognized journal, which is currently under review

Design and analysis of wideband passive microwave devices using planar structures

A selected volume of work consisting of 84 published journal papers is presented to demonstrate the contributions made by the author in the last seven years of his work at the University of Queensland in the area of Microwave Engineering. The over-arching theme in the author’s works included in this volume is the engineering of novel passive microwave devices that are key components in the building of any microwave system. The author’s contribution covers innovative designs, design methods and analyses for the following key devices and associated systems: Wideband antennas and associated systems Band-notched and multiband antennas Directional couplers and associated systems Power dividers and associated systems Microwave filters Phase shifters Much of the motivation for the work arose from the desire to contribute to the engineering o

Data Acquisition Applications

Data acquisition systems have numerous applications. This book has a total of 13 chapters and is divided into three sections: Industrial applications, Medical applications and Scientific experiments. The chapters are written by experts from around the world, while the targeted audience for this book includes professionals who are designers or researchers in the field of data acquisition systems. Faculty members and graduate students could also benefit from the book

Antenna Design for 5G and Beyond

With the rapid evolution of the wireless communications, fifth-generation (5G) communication has received much attention from both academia and industry, with many reported efforts and research outputs and significant improvements in different aspects, such as data rate speed and resolution, mobility, latency, etc. In some countries, the commercialization of 5G communication has already started as well as initial research of beyond technologies such as 6G.MIMO technology with multiple antennas is a promising technology to obtain the requirements of 5G/6G communications. It can significantly enhance the system capacity and resist multipath fading, and has become a hot spot in the field of wireless communications. This technology is a key component and probably the most established to truly reach the promised transfer data rates of future communication systems. In MIMO systems, multiple antennas are deployed at both the transmitter and receiver sides. The greater number of antennas can make the system more resistant to intentional jamming and interference. Massive MIMO with an especially high number of antennas can reduce energy consumption by targeting signals to individual users utilizing beamforming.Apart from sub-6 GHz frequency bands, 5G/6G devices are also expected to cover millimeter-wave (mmWave) and terahertz (THz) spectra. However, moving to higher bands will bring new challenges and will certainly require careful consideration of the antenna design for smart devices. Compact antennas arranged as conformal, planar, and linear arrays can be employed at different portions of base stations and user equipment to form phased arrays with high gain and directional radiation beams. The objective of this Special Issue is to cover all aspects of antenna designs used in existing or future wireless communication systems. The aim is to highlight recent advances, current trends, and possible future developments of 5G/6G antennas