17 research outputs found

    Concurrent Multi-Band Envelope Tracking Power Amplifiers for Emerging Wireless Communications

    Get PDF
    Emerging wireless communication is shifting toward data-centric broadband services, resulting in employment of sophisticated and spectrum efficient modulation and access techniques. This yields communication signals with large peak-to-average power ratios (PAPR) and stringent linearity requirements. For example, future wireless communication standard, such as long term evolution advanced (LTE-A) require adoption of carrier aggregation techniques to improve their effective modulation bandwidth. The carrier aggregation technique for LTE-A incorporates multiple carriers over a wide frequency range to create a wider bandwidth of up to 100MHz. This will require future power amplifiers (PAs) and transmitters to efficiently amplify concurrent multi-band signals with large PAPR, while maintaining good linearity. Different back-off efficiency enhancement techniques are available, such as envelope tracking (ET) and Doherty. ET has gained a lot of attention recently as it can be applied to both base station and mobile transmitters. Unfortunately, few publications have investigated concurrent multi-band amplification using ET PAs, mainly due to the limited bandwidth of the envelope amplifier. In this thesis, a novel approach to enable concurrent amplification of multi-band signals using a single ET PA will be presented. This thesis begins by studying the sources of nonlinearities in single-band and dual-band PAs. Based on the analysis, a design methodology is proposed to reduce the sources of memory effects in single-band and dual-band PAs from the circuit design stage and improve their linearizability. Using the proposed design methodology, a 45W GaN PA was designed. The PA was linearized using easy to implement, memoryless digital pre-distortion (DPD) with 8 and 28 coefficients when driven with single-band and dual-band signals, respectively. This analysis and design methodology will enable the design of PAs with reduced memory effects, which can be linearized using simple, power efficient linearization techniques, such as lookup table or memoryless polynomial DPD. Note that the power dissipation of the linearization engine becomes crucial as we move toward smaller base station cells, such as femto- and pico-cells, where complicated DPD models cannot be implemented due to their significant power overhead. This analysis is also very important when implementing a multi-band ET PA system, where the sources of memory effects in the PA itself are minimized through the proposed design methodology. Next, the principle of concurrent dual-band ET operation using the low frequency component (LFC) of the envelope of the dual-band signal is presented. The proposed dual-band ET PA modulates the drain voltage of the PA using the LFC of the envelope of the dual-band signal. This will enable concurrent dual-band operation of the ET PA without posing extra bandwidth requirements on the envelope amplifier. A detailed efficiency and linearity analysis of the dual-band ET PA is also presented. Furthermore, a new dual-band DPD model with supply dependency is proposed in this thesis, capable of capturing and compensating for the sources of distortion in the dual-band ET PA. To the best of our knowledge, concurrent dual-band operation of ET PAs using the LFC of the envelope of the dual-band signal is presented for the first time in the literature. The proposed dual-band ET operation is validated using the measurement results of two GaN ET PA prototypes. Lastly, the principle of concurrent dual-band ET operation is extended to multi-band signals using the LFC of the envelope of the multi-band signal. The proposed multi-band ET operation is validated using the measurement results of a tri-band ET PA. To the best of our knowledge, this is the first reported tri-band ET PA in literature. The tri-band ET PA is linearized using a new tri-band DPD model with supply dependency

    RF Power Amplifier and Its Envelope Tracking

    Get PDF
    This dissertation introduces an agile supply modulator with optimal transient performance for the envelope tracking supply in linear power amplifiers. For this purpose, an on-demand current source module, the bang-bang transient performance enhancer (BBTPE), is proposed. Its objective is to follow fast variations in input signals with reduced overshoot and settling time without deteriorating the steady-state performance of the buck regulator. The proposed approach enables fast system response through the BBTPE and an accurate steady-state output response through a low switching ripple and power efficient dynamic buck regulator. Fast output response with the help of the added module induces a slower rise of inductor current in the buck converter that further assists the proposed system to reduce both overshoot and settling time. To demonstrate the feasibility of the proposed solution, extensive simulations and experimental results from a discrete system are reported. The proposed supply modulator shows 80% improvement in rise time along with 60% reduction in both overshoot and settling time compared to the conventional dynamic buck regulator-based solution. Experimental results for a PA using the LTE 16-QAM 5 MHz standard shows improvement of 7.68 dB and 65.1% in ACPR and EVM, respectively. In a polar power amplifier, the input signal splits into phase and amplitude components using a non-linear conversion operation. This operation broadens the spectrum of the polar signal components. The information of amplitude and phase contains spectral images due to the sampling operation in non-linear conversion operation. These spectral images can be large and cause out-of-band emission in the output spectrum. In addition, during the recombination process of phase and amplitude, a delay mismatch between amplitude and phase signals, which can occur due to separate processing paths of amplitude and phase signals, causes out-of-band emissions, also known as spectral regrowth. This dissertation presents solutions to both of the issues of digital polar power amplifier: spectral images and delay mismatch. In order to reduce the problem of spectral images, interpolation of phase and amplitude is proposed in this work. This increases the effective sampling frequency of the amplitude and phase, which helps to improve the linearity by around 10 dB. In addition, a novel calibration scheme is proposed here for the delay mismatch between phase and amplitude path in a digital polar power amplifier. The scheme significantly reduces the spectral regrowth. The scheme uses the same path for phase and amplitude delay calculation after the recombination that allows having a robust calibration. Furthermore, it can be executed during the empty transmission slots. The proposed scheme is designed in a 40 nm CMOS technology and simulated with a 64-QAM IEEE 802.11n wireless standard. The scheme achieved 7.57 dB enhancement in ACLR and 84.35% improvement in EVM for a 3.5 ns mismatch in phase and amplitude path

    High Efficiency Microwave Amplifiers and SiC Varactors Optimized for Dynamic Load Modulation

    Get PDF
    The increasing use of mobile networks as the main source of internet connectivity is creating challenges in the infrastructure. Customer demand is a moving target and continuous hardware developments are necessary to supply higher data rates in an environmentally sustainable and cost effective way. This thesis reviews and advances the status of realizing wideband and high efficiency power amplifiers, which will facilitate improvements in network capacity and energy efficiency. Several demonstrator PAs are proposed, analyzed, designed, and characterized: First, resistive loading at higher harmonics in wideband power amplifier design suitable for envelope tracking (ET) is proposed. A 40 dBm decade bandwidth 0.4–4.1 GHz PA is designed, with 10–15 dB gain and 40–62% drain efficiency. Its versatility is demonstrated by digital pre-distortion (DPD) linearized measurements resulting in adjacent channel leakage ratios (ACLR) lower than −46 dBc for various downlink signals (WCDMA, LTE, WiMAX). Second, a theory for class-J microwave frequency dynamic load modulation (DLM) PAs is derived. This connects transistor technology and load network requirements to enable power-scalable and bandwidth conscious designs. A 38 dBm PA is designed at 2.08 GHz, maintaining efficiencies >45% over 8 dB of output power back-off (OPBO) dynamic range. From this pre-study a fully packaged 86-W peak power version at 2.14 GHz is designed. ACLR after DPD is −46 dBc at a drain efficiency of 34%. For DLM PAs there is a need for varactors with large effective tuning range and high breakdown voltage. For this purpose, SiC Schottky diode varactors are developed with an effective tuning range of 6:1 and supporting a 3:1 tuning ratio at 36 V of RF swing. Nonlinear characterization to enable Q-factor extraction in the presence of distortion is proposed and demonstrated by multi-harmonic active source- and load-pull, offering insights to tunable network design. Third, a method to evaluate and optimize dual-RF input PAs, while catering to higher harmonic conditions and transistor parasitics, is proposed. The method is validated by a PA design having a peak power of 44 +/- 0.9 dBm and 6 dB OPBO PAE exceeding 45% over a 1–3 GHz bandwidth. The results in this thesis contribute with a novel device and analysis of high efficiency and wideband PAs, aiding in the design of key components for future energy efficient and high capacity wireless systems

    Linear Operation of Switch-Mode Outphasing Power Amplifiers

    Get PDF
    Radio transceivers are playing an increasingly important role in modern society. The ”connected” lifestyle has been enabled by modern wireless communications. The demand that has been placed on current wireless and cellular infrastructure requires increased spectral efficiency however this has come at the cost of power efficiency. This work investigates methods of improving wireless transceiver efficiency by enabling more efficient power amplifier architectures, specifically examining the role of switch-mode power amplifiers in macro cell scenarios. Our research focuses on the mechanisms within outphasing power amplifiers which prevent linear amplification. From the analysis it was clear that high power non-linear effects are correctable with currently available techniques however non-linear effects around the zero crossing point are not. As a result signal processing techniques for suppressing and avoiding non-linear operation in low power regions are explored. A novel method of digital pre-distortion is presented, and conventional techniques for linearisation are adapted for the particular needs of the outphasing power amplifier. More unconventional signal processing techniques are presented to aid linearisation of the outphasing power amplifier, both zero crossing and bandwidth expansion reduction methods are designed to avoid operation in nonlinear regions of the amplifiers. In combination with digital pre-distortion the techniques will improve linearisation efforts on outphasing systems with dynamic range and bandwidth constraints respectively. Our collaboration with NXP provided access to a digital outphasing power amplifier, enabling empirical analysis of non-linear behaviour and comparative analysis of behavioural modelling and linearisation efforts. The collaboration resulted in a bench mark for linear wideband operation of a digital outphasing power amplifier. The complimentary linearisation techniques, bandwidth expansion reduction and zero crossing reduction have been evaluated in both simulated and practical outphasing test benches. Initial results are promising and indicate that the benefits they provide are not limited to the outphasing amplifier architecture alone. Overall this thesis presents innovative analysis of the distortion mechanisms of the outphasing power amplifier, highlighting the sensitivity of the system to environmental effects. Practical and novel linearisation techniques are presented, with a focus on enabling wide band operation for modern communications standards

    RF Power Amplifier and Its Envelope Tracking

    Get PDF
    This dissertation introduces an agile supply modulator with optimal transient performance for the envelope tracking supply in linear power amplifiers. For this purpose, an on-demand current source module, the bang-bang transient performance enhancer (BBTPE), is proposed. Its objective is to follow fast variations in input signals with reduced overshoot and settling time without deteriorating the steady-state performance of the buck regulator. The proposed approach enables fast system response through the BBTPE and an accurate steady-state output response through a low switching ripple and power efficient dynamic buck regulator. Fast output response with the help of the added module induces a slower rise of inductor current in the buck converter that further assists the proposed system to reduce both overshoot and settling time. To demonstrate the feasibility of the proposed solution, extensive simulations and experimental results from a discrete system are reported. The proposed supply modulator shows 80% improvement in rise time along with 60% reduction in both overshoot and settling time compared to the conventional dynamic buck regulator-based solution. Experimental results for a PA using the LTE 16-QAM 5 MHz standard shows improvement of 7.68 dB and 65.1% in ACPR and EVM, respectively. In a polar power amplifier, the input signal splits into phase and amplitude components using a non-linear conversion operation. This operation broadens the spectrum of the polar signal components. The information of amplitude and phase contains spectral images due to the sampling operation in non-linear conversion operation. These spectral images can be large and cause out-of-band emission in the output spectrum. In addition, during the recombination process of phase and amplitude, a delay mismatch between amplitude and phase signals, which can occur due to separate processing paths of amplitude and phase signals, causes out-of-band emissions, also known as spectral regrowth. This dissertation presents solutions to both of the issues of digital polar power amplifier: spectral images and delay mismatch. In order to reduce the problem of spectral images, interpolation of phase and amplitude is proposed in this work. This increases the effective sampling frequency of the amplitude and phase, which helps to improve the linearity by around 10 dB. In addition, a novel calibration scheme is proposed here for the delay mismatch between phase and amplitude path in a digital polar power amplifier. The scheme significantly reduces the spectral regrowth. The scheme uses the same path for phase and amplitude delay calculation after the recombination that allows having a robust calibration. Furthermore, it can be executed during the empty transmission slots. The proposed scheme is designed in a 40 nm CMOS technology and simulated with a 64-QAM IEEE 802.11n wireless standard. The scheme achieved 7.57 dB enhancement in ACLR and 84.35% improvement in EVM for a 3.5 ns mismatch in phase and amplitude path

    Arquiteturas paralelas avançadas para transmissores 5G totalmente digitais

    Get PDF
    The fifth generation of mobile communications (5G) is being prepared and should be rolled out in the early coming years. Massive number of Radio-Frequency (RF) front-ends, peak data rates of 10 Gbps (everywhere and everytime), latencies lower than 10 msec and huge device densities are some of the expected disruptive capabilities. At the same time, previous generations can not be jeopardized, fostering the design of novel flexible and highly integrated radio transceivers able to support the simultaneous transmission of multi-band and multi-standard signals. The concept of all-digital transmission is being pointed out as a promising architecture to cope with such challenging requirements, due to its fully digital radio datapath. This thesis is focused on the proposal and validation of fully integrated and advanced digital transmitter architectures that excel the state-of-the-art in different figures of merit, such as transmission bandwidth, spectral purity, carrier agility, flexibility, and multi-band capability. The first part of this thesis introduces the concept of all-digital RF transmission. In particular, the foundations inherent to this thematic line are given, together with the recent advances reported in the state-of-the-art architectures.The core of this thesis, containing the main developments achieved during the Ph.D. work, is then presented and discussed. The first key contribution to the state-of-the-art is the use of cascaded Delta-Sigma (∆Σ) architectures to relax the analog filtering requirements of the conventional All-Digital Transmitters while maintaining the constant envelope waveform. Then, it is presented the first reported architecture where Antenna Arrays are directly driven by single-chip and single-bit All-Digital Transmitters, with promising results in terms of simplification of the RF front-ends and overall flexibility. Subsequently, the thesis proposes the first reported RF-stage All-Digital Transmitter that can be embedded within a single Field-Programmable Gate Array (FPGA) device. Thereupon, novel techniques to enable the design of wideband All-Digital Transmitters are reported. Finally, the design of concurrent multi-band transmitters is introduced. In particular, the design of agile and flexible dual and triple bands All-DigitalTransmitter (ADT) is demonstrated, which is a very important topic for scenarios that demand carrier aggregation. This Ph.D. contributes withseveral advances to the state-of-the-art of RF all-digital transmitters.A quinta geração de comunicações móveis (5G) está a ser preparada e deve ser comercializada nos próximos anos. Algumas das caracterı́sticas inovadoras esperadas passam pelo uso de um número massivo de font-ends de Rádio-Frequência (RF), taxas de pico de transmissão de dados de 10 Gbps (em todos os lugares e em todas as ocasiões), latências inferiores a 10 mseg e elevadas densidades de dispositivos. Ao mesmo tempo, as gerações anteriores não podem ser ignoradas, fomentando o design de novos transceptores de rádio flexı́veis e altamente integrados, capazes de suportar a transmissão simultânea de sinais multi-banda e multi-standard. O conceito de transmissão totalmente digital é considerado como um tipo de arquitetura promissora para lidar com esses requisitos desafiantes, devido ao seu datapath de rádio totalmente digital. Esta tese é focada na proposta e validação de arquiteturas de transmissores digitais totalmente integradas e avançadas que ultrapassam o estado da arte em diferentes figuras de mérito, como largura de banda de transmissão, pureza espectral, agilidade de portadora, flexibilidade e capacidade multibanda. A primeira parte desta tese introduz o conceito de transmissores de RF totalmente digitais. Em particular, os fundamentos inerentes a esta linha temática são apresentados, juntamente com os avanços mais recentes do estado-da-arte. O núcleo desta tese, contendo os principais desenvolvimentos alcançados durante o trabalho de doutoramento, é então apresentado e discutido. A primeira contribuição fundamental para o estado da arte é o uso de arquiteturas em cascata com moduladores ∆Σ para relaxar os requisitos de filtragem analógica dos transmissores RF totalmente digitais convencionais, mantendo a forma de onda envolvente constante. Em seguida, é apresentada a primeira arquitetura em que agregados de antenas são excitados diretamente por transmissores digitais de um único bit inseridos num único chip, com resultados promissores em termos de simplificação dos front-ends de RF e flexibilidade em geral. Posteriormente, é proposto o primeiro transmissor totalmente digital RF-stage relatado que pode ser incorporado dentro de um único Agregado de Células Lógicas Programáveis. Novas técnicas para permitir o desenho de transmissores RF totalmente digitais de banda larga são também apresentadas. Finalmente, o desenho de transmissores simultâneos de múltiplas bandas é exposto. Em particular, é demonstrado o desenho de transmissores de duas e três bandas ágeis e flexı́veis, que é um tópico essencial para cenários que exigem agregação de múltiplas bandas.Apoio financeiro da Fundação para a Ciência e Tecnologia (FCT) no âmbito de uma bolsa de doutoramento, ref. PD/BD/105857/2014.Programa Doutoral em Telecomunicaçõe

    Characterization and modelling of software defined radio front-ends

    Get PDF
    Doutoramento em Engenharia ElectrotécnicaO presente trabalho tem por objectivo estudar a caracterização e modelação de arquitecturas de rádio frequência para aplicações em rádios definidos por software e rádios cognitivos. O constante aparecimento no mercado de novos padrões e tecnologias para comunicações sem fios têm levantado algumas limitações à implementação de transceptores rádio de banda larga. Para além disso, o uso de sistemas reconfiguráveis e adaptáveis baseados no conceito de rádio definido por software e rádio cognitivo assegurará a evolução para a próxima geração de comunicações sem fios. A ideia base desta tese passa por resolver alguns problemas em aberto e propor avanços relevantes, tirando para isso partido das capacidades providenciadas pelos processadores digitais de sinal de forma a melhorar o desempenho global dos sistemas propostos. Inicialmente, serão abordadas várias estratégias para a implementação e projecto de transceptores rádio, concentrando-se sempre na aplicabilidade específica a sistemas de rádio definido por software e rádio cognitivo. Serão também discutidas soluções actuais de instrumentação capaz de caracterizar um dispositivo que opere simultaneamente nos domínios analógico e digital, bem como, os próximos passos nesta área de caracterização e modelação. Além disso, iremos apresentar novos formatos de modelos comportamentais construídos especificamente para a descrição e caracterização não-linear de receptores de amostragem passa-banda, bem como, para sistemas nãolineares que utilizem sinais multi-portadora. Será apresentada uma nova arquitectura suportada na avaliação estatística dos sinais rádio que permite aumentar a gama dinâmica do receptor em situações de multi-portadora. Da mesma forma, será apresentada uma técnica de maximização da largura de banda de recepção baseada na utilização do receptor de amostragem passa-banda no formato complexo. Finalmente, importa referir que todas as arquitecturas propostas serão acompanhadas por uma introdução teórica e simulações, sempre que possível, sendo após isto validadas experimentalmente por protótipos laboratoriais.This work investigates the characterization and modeling of radio frequency front-ends for software defined radio and cognitive radio applications. The emergence of new standards and technologies in the wireless communications market are raising several issues to the implementation of wideband transceiver systems. Also, reconfigurable and adaptable systems based on software defined and cognitive radio models are paving the way for the next generation of wireless systems. In this doctoral thesis the fundamental idea is to address the particular open issues and propose appropriate advancements by exploring and taking profit from new capabilities of digital signal processors in a way to improve the overall performance of the novel schemes. Receiver and transmitter strategies for radio communications are summarized by concentrating on the usability for software defined radio and cognitive radio systems. Available instrumentation and next steps for analog and digital radio frequency hardware characterization is also discussed. Wideband behavioral model formats are proposed for nonlinear description and characterization of bandpass sampling receivers, as well as, for multi-carrier nonlinear systems operation. The proposed models share a great flexibility and have the freedom to be simply expanded to other fields. A new design for receiver dynamic range improvement in multi-carrier scenarios is proposed, which is supported on the useful wireless signals statistical evaluation. Additionally, receiver-side bandwidth maximization based on higher-order bandpass sampling approaches is evaluated. All the proposed designs and modeling strategies are accompanied by theoretical backgrounds and simulations whenever possible, being then experimentally validated by laboratory prototypes

    Novas arquiteturas para transmissores digitais flexíveis e de banda larga

    Get PDF
    Next generation of wireless communication (5G) devices must achieve higher data rates, lower power consumption and better coverage by making a more efficient use of the RF spectrum and adopting highly exible radio architectures. To meet these requirements, the development of new radio devices will be far more complex and challenging than their predecessors. The future of radio communications have a twofold evolution, being one the low power consumption and the other the adaptability and intelligent use of the available resources. Conventional approaches for the radio physical layer are not capable to cope with the new demand for multi-band, multi-standard radio signals and present an inefficient and expensive solution for simultaneous transmission of multiple and heterogeneous radio signals. Digital radio transmitters have been presented as a solution for a newer and more exible architecture for future radios. All-digital transmitters use a completely digital implementation of the entire radio datapath from the baseband processing to the digital RF up-conversion. This concept bene ts from the use of highly integrated hardware together with a strong radio digitalization, motivated by the exibility and high performance from cognitive and software defi ned radio. However, such devices are still far from a massive deployment in most of communication scenarios due to some limiting factors that hinder their use. This PhD thesis aims to the development of novel radio architectures and ideas based on all-digital transmitters capable of improving the adaptability and use intelligently the available resources for software de ned and cognitive radio systems. The focus of this thesis is on the improvement of some of the common limitations for all-digital transmitters such as power efficiency, bandwidth, noise-shaping and exibility while using efficient and adaptable digital architectures. In the initial part of the thesis a review of the state-of-the-art is presented showing the most common digital transmitter architectures as well as their major bene ts and key limitations. A comparative analysis of such architectures is made considering their power and spectral efficiency, exibility, performance and cost. Following this initial analysis, the work developed on the course of this PhD is presented and discussed. The initial focus is on the improvement of all-digital transmitters bandwidth trough the study and use of parallel processing techniques capable of greatly improve common bandwidth values presented in the state-of-the-art. The presented work has resulted in several publications where FPGA-based architectures use parallel digital processing techniques to improve the system's bandwidth by a factor higher than 10. Other fundamental contribution of this thesis is focused on the pulsedtransmitters coding efficiency. In this section of the thesis, a method is presented showing the reduction of the quantization noise created by low amplitude resolution digital transmitters using multiple combined pulsedtransmitters to cancel the noise in speci c frequencies. This work has resulted in two main publications that showed how to increase the coding efficiency of the pulse-transmitters as well as the overall efficiency of the transmission system. Lastly, new-noise shaping methods are presented in order to develop new and more exible architectures for all-digital transmitters. The methods presented use new quantization processes that allow for the shaping of the quantization noise produced in pulsed-transmitters while using very simple and adaptable architectures. With these new techniques, it is possible to adjust the noise frequency distribution and deliberately change the noise shape in order to change some of the transmitter's characteristics such as central frequency or bandwidth. The work presented on this thesis has shown promising improvements to the all-digital transmitters' state-of-the-art, either in simulations and laboratory prototype measurements. It has contributed to advance the state-of-the-art in agile and power efficient all-digital RF transmitters with multi-mode and multi-channel capabilities and the improvement of the transceiver's bandwidth enabling the development of true software de ned and cognitive radio systemsA próxima geração de comunicações sem os (5G) exigirá taxas de transmissão mais elevadas, maior efi ciência energética e uma melhor cobertura fazendo um uso mais efi ciente do espectro de radiofrequência e adotando o uso de arquiteturas rádio mais flexíveis. Para cumprir tais requisitos, o desenvolvimento de novos dispositivos rádio será substancialmente mais complexo do que nas gerações anteriores. O futuro das comunicações rádio depende maioritariamente de dois fatores; o baixo consumo de potência e o uso inteligente dos recursos e tecnologias disponíveis. As abordagens convencionais para a camada física dos sistemas rádio não são as mais adequadas para lidar com a necessidade de dispositivos multi-banda e que usem múltiplos standards, por serem soluções inefi cientes e demasiado caras para esse efeito. Os transmissores rádio completamente digitais têm vindo a ser apresentados na literatura como uma solução inovadora e mais flexível para a implementação dos futuros sistemas de rádio. Os transmissores completamente digitais apresentam uma implementação da cadeia de processamento rádio, desde a banda-base até à conversão para RF, completamente constituída por lógica digital. Este conceito tira partido da vasta integração alcançada nas arquiteturas digitais, juntamente com a flexibilidade proveniente da digitalização das arquiteturas rádio que já se encontra em curso com a evolução dos rádios cognitivos e definidos por software. No entanto, devido a algumas limitações inerentes à tecnologia, este tipo de transmissores ainda não é amplamente utilizado na maioria dos sistemas. Esta tese de doutoramento propõe e avalia novas arquiteturas para transmissores completamente digitais, bem como novas técnicas de processamento de sinal que possam beneficiar das tecnologias de implementação existentes (e.g. FPGAs) por forma a construir novos transmissores digitais de forma eficiente e flexível. O objetivo desta tese é reduzir as limitações atuais ainda presentes neste tipo de transmissores, nomeadamente as relacionadas com a eficiência, largura de banda, cancelamento de ruído e falta de flexibilidade. Na parte inicial desta tese é realizada a revisão do estado da arte das diversas topologias de transmissores digitais bem como as suas principais vantagens e limitações técnicas. É também feita uma análise comparativa das diversas técnicas apresentadas em termos da sua eficiência energética, flexibilidade, desempenho e custo. De seguida, é apresentado o trabalho desenvolvido no contexto desta tese de doutoramento, seguindo-se uma discussão focada na resolução das atuais limitações deste tipo de transmissores. A primeira parte foca-se no uso de técnicas de processamento paralelo de sinal, por forma a suportar sinais de largura de banda mais elevada que os reportados no atual estado da arte. O trabalho desenvolvido e publicado baseia-se no uso de arquiteturas implementadas em FPGA que contribuíram para um aumento da largura de banda num fator de aproximadamente dez vezes. Outra das contribuições fundamentais desta tese consiste no aumento da eficiência do sistema através da melhoria da eficiência de codificação do sinal pulsado produzido. Com base no uso de múltiplos transmissores pulsados, e apresentado um esquema de combinação construtiva e destrutiva de sinais para a redução do ruído de quantização proveniente das técnicas de processamento de sinal pulsado usadas. Este trabalho resultou em duas importantes publicações que mostram que a melhoria da eficiência de codificação do sinal pode ser utilizada de forma a obter uma maior eficiência energética do transmissor. Por ultimo, são apresentadas diversas técnicas para a conversão dos sinais banda-base em sinais RF pulsados. As propostas apresentadas permitem o uso de uma arquitetura de hardware simplista, mas configurável por software, o que a torna bastante flexível. Com o uso desta arquitetura e possível alterar em pleno funcionamento a frequência central bem como a largura de banda e resposta do conversor pulsado. O trabalho apresentado nesta tese demonstra alguns dos melhoramentos no estado da arte para transmissores r adio completamente digitais, baseando os resultados obtidos não apenas em simulações mas também na implementação e medidas realizadas sobre protótipos laboratoriais. O trabalho desenvolvido no âmbito desta tese contribuiu com avanços na implementação de transmissores ageis, eficientes, com maior largura de banda e capazes de transmissão em múltiplas bandas com recurso a múltiplos protocolos, abrindo caminho para o desenvolvimento de novos rádios cognitivos e definidos por softwareFCT, FSEPrograma Doutoral em Engenharia Eletrotécnic

    Analytical Approaches to Load Modulation Power Amplifier Design

    Get PDF
    In future mobile communication networks, there will be a shift toward higher carrier frequencies and highly integrated multiple antenna systems. The system performance will largely depend on the available radio frequency (RF) hardware. As such, RF power amplifiers (PAs) with improved performance, e.g. energy efficiency, are needed. Active load modulation (ALM) is one of the most common PA efficiency enhancement techniques. Unfortunately, different ALM techniques come at the cost of degrading other PA attributes. Through investigation of new ALM design techniques, the overall objective of this thesis is to improve upon different attributes and performance trade-offs in ALM PAs for future wireless systems.\ua0The working principle of ALM PAs is determined by both how the individual transistors are operated and how their outputs are combined. In the first part of the thesis, an analytical approach, where the output combiner is assumed to be an arbitrary black-box, is applied to the Doherty PA. The fundamental interaction between the main and auxiliary transistors is analyzed and generalized. New solutions with improved performance are identified, such as higher gain and an improved efficiency-linearity trade-off. This approach also introduces improved integration possibilities, which are demonstrated by a transmitter where the antenna acts as both the radiator and the Doherty combiner. Additionally, the analytical approach is applied to an isolated two-way power divider. This unlocks many new possibilities, such as improved integration and layout flexibility. \ua0In the second part, one embodiment of the emerging ALM architecture, the load modulated balanced amplifier (LMBA), is proposed: the RF-input Doherty-like LMBA. Design equations are derived and the fundamental operation is studied. This variant presents several advantages over other known architectures, such as higher gain and device periphery scaling of the different transistors.\ua0The third part proposes a new measurement-based ALM PA design procedure, which emulates the full behavior of the transistors in any ALM architecture using active load-pull measurements. This method can predict the intricate behavior in ALM PAs and it gives measurement-based insights into the internal operation of the circuit already at the design stage. This facilitates the design for optimal ALM PA performance. \ua0The thesis contributes with several promising techniques for reducing performance trade-offs and improving the overall performance of ALM PAs. Therefore, the results will contribute to the development of more energy efficient and high capacity wireless services in the future
    corecore