Enhancing diversity and multiplexing gains in multi-user wireless relay systems

The demand for higher transmission rates and better quality of service in modern wireless communications is endless. The use of multiple transmit or /and receive antennas has been considered as one of the most powerful approaches to facilitate high -speed and high -quality communications. However, in practical cellular systems, mobile terminals may not be able to support a multiple- antenna setup. Thus an emerging technique called cooperative diversity is under consideration to utilize the multi -hop relay concept to realize the advantages of multiple - antenna systems in multi -user single- antenna networks. Cooperative diversity has attracted much interest in recent years as a very promising direction for future wireless communication evolution.Due to the fact that in practice terminals cannot transmit and receive simultaneously (i.e. the half -duplex limitation), the diversity improvement brought by the standard cooperative diversity transmission protocols is in general accompanied by a multiplexing loss (equivalent to a reduction in transmission data rate in high signal -to -nose ratio (SNR)). The purpose of this thesis is to use advanced transmission protocols to provide both good diversity and multiplexing performance when using the practical repetition -coded decode - and -forward (DF) relaying strategy in uplink mobile -to -base station transmission of cellular systems.The task is fulfilled by relaxing the orthogonal channel allocation requirement of the standard protocols and by using two relays to take turns forwarding source information to destination. We start our analysis from an M- source two -relay one -destination network. Through diversity -multiplexing tradeoff (DMT) analysis, we prove that for an isolated -relay scenario and a strong -interference scenario, the considered approach effectively recovers the multiplexing loss induced by the standard protocols while still obtaining diversity improvement over direct source -destination transmission without considering relaying.In addition, since the optimal multiplexing gain of the considered system can be achieved by the above approach, we study further improving diversity performance for a two -source network. We analyze taking full advantage of the multiple- source structure, multiple -relay structure, and the capability of affording complex signal processing at the destination (base station). For all three cases, we prove that the diversity performance of the above approach can be enhanced without a significant loss of multiplexing performance or using complex coding strategies at relays. Since the good DMT performance is not affected by source -relay channel conditions, the protocols discussed in this thesis make relaying more beneficial

Power Optimisation and Relay Selection in Cooperative Wireless Communication Networks

Cooperative communications have emerged as a significant concept to improve reliability and throughput in wireless systems. In cooperative networks, the idea is to implement a scheme in wireless systems where the nodes can harmonize their resources thereby enhancing the network performance in different aspects such as latency, BER and throughput. As cooperation spans from the basic idea of transmit diversity achieved via MIMO techniques and the relay channel, it aims to reap somewhat multiple benefits of combating fading/burst errors, increasing throughput and reducing energy use. Another major benefit of cooperation in wireless networks is that since the concept only requires neighbouring nodes to act as virtual relay antennas, the concept evades the negative impacts of deployment costs of multiple physical antennas for network operators especially in areas where they are difficult to deploy. In cooperative communications energy efficiency and long network lifetimes are very important design issues, the focus in this work is on ad hoc and sensor network varieties where the nodes integrate sensing, processing and communication such that their cooperation capabilities are subject to power optimisation. As cooperation communications leads to trade-offs in Quality of Services and transmit power, the key design issue is power optimisation to dynamically combat channel fluctuations and achieve a net reduction of transmit power with the goal of saving battery life. Recent researches in cooperative communications focus on power optimisation achieved via power control at the PHY layer, and/or scheduling mechanism at the MAC layer. The approach for this work will be to review the power control strategy at the PHY layer, identify their associated trade-offs, and use this as a basis to propose a power control strategy that offers adaptability to channel conditions, the road to novelty in this work is a channel adaptable power control algorithm that jointly optimise power allocation, modulation strategy and relay selection. Thus, a novel relay selection method is developed and implemented to improve the performance of cooperative wireless networks in terms of energy consumption. The relay selection method revolves on selection the node with minimum distance to the source and destination. The design is valid to any wireless network setting especially Ad-hoc and sensor networks where space limitations preclude the implementation of bigger capacity battery. The thesis first investigates the design of relay selection schemes in cooperative networks and the associated protocols. Besides, modulation strategy and error correction code impact on energy consumption are investigated and the optimal solution is proposed and jointly implemented with the relay selection method. The proposed algorithm is extended to cooperative networks in which multiple nodes participate in cooperation in fixed and variable rate system. Thus, multi relay selection algorithm is proposed to improve virtual MIMO performance in terms of energy consumption. Furthermore, motivated by the trend of cell size optimisation in wireless networks, the proposed relay selection method is extended to clustered wireless networks, and jointly implemented with virtual clustering technique. The work will encompass three main stages: First, the cooperative system is designed and two major protocols Decode and Forward (DF) and amplify and forward (AF) are investigated. Second, the proposed algorithm is modelled and tested under different channel conditions with emphasis on its performance using different modulation strategies for different cooperative wireless networks. Finally, the performance of the proposed algorithm is illustrated and verified via computer simulations. Simulation results show that the distance based relay selection algorithm exhibits an improved performance in terms of energy consumption compared to the conventional cooperative schemes under different cooperative communication scenarios

On the Performance of Cognitive Underlay SIMO Networks over Equally Correlated Rayleigh Fading Channels

The performance of single-input multiple-output (SIMO) cognitive spectrum sharing networks with the presence of equally correlated Rayleigh fading channels is investigated. In particular, based on the truncated infinitive series of cumulative distribution function (CDF) and probability density function (PDF) of the end-to-end signal-to-noise ratios (SNRs), close-form expressions are provided for the system outage performance, bit error rate and ergodic capacity. It is shown that the system performance merely depends on the correlation coefficient between antennas. Monte-Carlo simulations are also contributed to confirm the accuracy of our analysis

Joint transceiver design and power optimization for wireless sensor networks in underground mines

Avec les grands développements des technologies de communication sans fil, les réseaux de capteurs sans fil (WSN) ont attiré beaucoup d’attention dans le monde entier au cours de la dernière décennie. Les réseaux de capteurs sans fil sont maintenant utilisés pour a surveillance sanitaire, la gestion des catastrophes, la défense, les télécommunications, etc. De tels réseaux sont utilisés dans de nombreuses applications industrielles et commerciales comme la surveillance des processus industriels et de l’environnement, etc. Un réseau WSN est une collection de transducteurs spécialisés connus sous le nom de noeuds de capteurs avec une liaison de communication distribuée de manière aléatoire dans tous les emplacements pour surveiller les paramètres. Chaque noeud de capteur est équipé d’un transducteur, d’un processeur de signal, d’une unité d’alimentation et d’un émetteur-récepteur. Les WSN sont maintenant largement utilisés dans l’industrie minière souterraine pour surveiller certains paramètres environnementaux, comme la quantité de gaz, d’eau, la température, l’humidité, le niveau d’oxygène, de poussière, etc. Dans le cas de la surveillance de l’environnement, un WSN peut être remplacé de manière équivalente par un réseau à relais à entrées et sorties multiples (MIMO). Les réseaux de relais multisauts ont attiré un intérêt de recherche important ces derniers temps grâce à leur capacité à augmenter la portée de la couverture. La liaison de communication réseau d’une source vers une destination est mise en oeuvre en utilisant un schéma d’amplification/transmission (AF) ou de décodage/transfert (DF). Le relais AF reçoit des informations du relais précédent et amplifie simplement le signal reçu, puis il le transmet au relais suivant. D’autre part, le relais DF décode d’abord le signal reçu, puis il le transmet au relais suivant au deuxième étage s’il peut parfaitement décoder le signal entrant. En raison de la simplicité analytique, dans cette thèse, nous considérons le schéma de relais AF et les résultats de ce travail peuvent également être développés pour le relais DF. La conception d’un émetteur/récepteur pour le relais MIMO multisauts est très difficile. Car à l’étape de relais L, il y a 2L canaux possibles. Donc, pour un réseau à grande échelle, il n’est pas économique d’envoyer un signal par tous les liens possibles. Au lieu de cela, nous pouvons trouver le meilleur chemin de la source à la destination qui donne le rapport signal sur bruit (SNR) de bout en bout le plus élevé. Nous pouvons minimiser la fonction objectif d’erreur quadratique moyenne (MSE) ou de taux d’erreur binaire (BER) en envoyant le signal utilisant le chemin sélectionné. L’ensemble de relais dans le chemin reste actif et le reste des relais s’éteint, ce qui permet d’économiser de l’énergie afin d’améliorer la durée de vie du réseau. Le meilleur chemin de transmission de signal a été étudié dans la littérature pour un relais MIMO à deux bonds mais est plus complexe pour un ...With the great developments in wireless communication technologies, Wireless Sensor Networks (WSNs) have gained attention worldwide in the past decade and are now being used in health monitoring, disaster management, defense, telecommunications, etc. Such networks are used in many industrial and consumer applications such as industrial process and environment monitoring, among others. A WSN network is a collection of specialized transducers known as sensor nodes with a communication link distributed randomly in any locations to monitor environmental parameters such as water level, and temperature. Each sensor node is equipped with a transducer, a signal processor, a power unit, and a transceiver. WSNs are now being widely used in the underground mining industry to monitor environmental parameters, including the amount of gas, water, temperature, humidity, oxygen level, dust, etc. The WSN for environment monitoring can be equivalently replaced by a multiple-input multiple-output (MIMO) relay network. Multi-hop relay networks have attracted significant research interest in recent years for their capability in increasing the coverage range. The network communication link from a source to a destination is implemented using the amplify-and-forward (AF) or decode-and-forward (DF) schemes. The AF relay receives information from the previous relay and simply amplifies the received signal and then forwards it to the next relay. On the other hand, the DF relay first decodes the received signal and then forwards it to the next relay in the second stage if it can perfectly decode the incoming signal. For analytical simplicity, in this thesis, we consider the AF relaying scheme and the results of this work can also be developed for the DF relay. The transceiver design for multi-hop MIMO relay is very challenging. This is because at the L-th relay stage, there are 2L possible channels. So, for a large scale network, it is not economical to send the signal through all possible links. Instead, we can find the best path from source-to-destination that gives the highest end-to-end signal-to-noise ratio (SNR). We can minimize the mean square error (MSE) or bit error rate (BER) objective function by sending the signal using the selected path. The set of relay in the path remains active and the rest of the relays are turned off which can save power to enhance network life-time. The best path signal transmission has been carried out in the literature for 2-hop MIMO relay and for multiple relaying it becomes very complex. In the first part of this thesis, we propose an optimal best path finding algorithm at perfect channel state information (CSI). We consider a parallel multi-hop multiple-input multiple-output (MIMO) AF relay system where a linear minimum mean-squared error (MMSE) receiver is used at the destination. We simplify the parallel network into equivalent series multi-hop MIMO relay link using best relaying, where the best relay ..

Physical Layer Security in Wireless Networks: Design and Enhancement.

PhDSecurity and privacy have become increasingly significant concerns in wireless communication networks, due to the open nature of the wireless medium which makes the wireless transmission vulnerable to eavesdropping and inimical attacking. The emergence and development of decentralized and ad-hoc wireless networks pose great challenges to the implementation of higher-layer key distribution and management in practice. Against this background, physical layer security has emerged as an attractive approach for performing secure transmission in a low complexity manner. This thesis concentrates on physical layer security design and enhancement in wireless networks. First, this thesis presents a new unifying framework to analyze the average secrecy capacity and secrecy outage probability. Besides the exact average secrecy capacity and secrecy outage probability, a new approach for analyzing the asymptotic behavior is proposed to compute key performance parameters such as high signal-to-noise ratio slope, power offset, secrecy diversity order, and secrecy array gain. Typical fading environments such as two-wave with diffuse power and Nakagami-m are taken into account. Second, an analytical framework of using antenna selection schemes to achieve secrecy is provided. In particular, transmit antenna selection and generalized selection combining are considered including its special cases of selection combining and maximal-ratio combining. Third, the fundamental questions surrounding the joint impact of power constraints on the cognitive wiretap channel are addressed. Important design insights are revealed regarding the interplay between two power constraints, namely the maximum transmit at the secondary network and the peak interference power at the primary network. Fourth, secure single carrier transmission is considered in the two-hop decode-andi forward relay networks. A two-stage relay and destination selection is proposed to minimize the eavesdropping and maximize the signal power of the link between the relay and the destination. In two-hop amplify-and-forward untrusted relay networks, secrecy may not be guaranteed even in the absence of external eavesdroppers. As such, cooperative jamming with optimal power allocation is proposed to achieve non-zero secrecy rate. Fifth and last, physical layer security in large-scale wireless sensor networks is introduced. A stochastic geometry approach is adopted to model the positions of sensors, access points, sinks, and eavesdroppers. Two scenarios are considered: i) the active sensors transmit their sensing data to the access points, and ii) the active access points forward the data to the sinks. Important insights are concluded