A DLL Based Test Solution for 3D ICs

Integrated circuits (ICs) are rapidly changing and vertical integration and packaging strategies have already become an important research topic. 2.5D and 3D IC integrations have obvious advantages over the conventional two dimensional IC implementations in performance, capacity, and power consumption. A passive Si interposer utilizing Through-Silicon via (TSV) technology is used for 2.5D IC integration. TSV is also the enabling technology for 3D IC integration. TSV manufacturing defects can affect the performance of stacked devices and reduce the yield. Manufacturing test methodologies for TSVs have to be developed to ensure fault-free devices. This thesis presents two test methods for TSVs in 2.5D and 3D ICs utilizing Delay-Locked Loop (DLL) modules. In the test method developed for TSVs in 2.5D ICs, a DLL is used to determine the propagation delay for fault detection. TSV faults in 3D ICs are detected through observation of the control voltage of a DLL. The proposed test methods present a robust performance against Process, supply Voltage and Temperature (PVT) variations due to the inherent feedback of DLLs. 3D full-wave simulations are performed to extract circuit level models for TSVs and fragments of an interposer wires using HFSS simulation tools. The extracted TSV models are then used to perform circuit level simulations using ADS tools from Agilent. Simulation results indicate that the proposed test solution for TSVs can detect manufacturing defects affecting the TSV propagation delay

Contactless Test Access Mechanism for 3D IC

3D IC integration presents many advantages over the current 2D IC integration. It has the potential to reduce the power consumption and the physical size while supporting higher bandwidth and processing speed. Through Silicon Via’s (TSVs) are vertical interconnects between different layers of 3D ICs with a typical 5μm diameter and 50μm length. To test a 3D IC, an access mechanism is needed to apply test vectors to TSVs and observe their responses. However, TSVs are too small for access by current wafer probes and direct TSV probing may affect their physical integrity. In addition, the probe needles for direct TSV probing must be cleaned or replaced frequently. Contactless probing method resolves most of the TSV probing problems and can be employed for small-pitch TSVs. In this dissertation, contactless test access mechanisms for 3D IC have been explored using capacitive and inductive coupling techniques. Circuit models for capacitive and inductive communication links are extracted using 3D full-wave simulations and then circuit level simulations are carried out using Advanced Design System (ADS) design environment to verify the results. The effects of cross-talk and misalignment on the communication link have been investigated. A contactless TSV probing method using capacitive coupling is proposed and simulated. A prototype was fabricated using TSMC 65nm CMOS technology to verify the proposed method. The measurement results on the fabricated prototype show that this TSV probing scheme presents -55dB insertion loss at 1GHz frequency and maintains higher than 35dB signal-to-noise ratio within 5µm distance. A microscale contactless probe based on the principle of resonant inductive coupling has also been designed and simulated. Experimental measurements on a prototype fabricated in TSMC 65nm CMOS technology indicate that the data signal on the TSV can be reconstructed when the distance between the TSV and the probe remains less than 15µm

TSV Equivalent Circuit Model using 3D Full-Wave Analysis

This work presents a study to build lumped models for fault-free and faulty Through Silicon Vias (TSVs). Three dimensional full-wave simulations are performed to extract equivalent circuit models. The effects of parametric and catastrophic faults due to pin-holes, voids and open circuits on the equivalent circuit models have been determined through 3D simulations. The extracted TSV models are then used to conduct delay tests to determine the required measurement resolution to detect TSV defects. It is shown that the substrate conductivity has a considerable effect on TSV fault characterization. It is also shown that, regardless of the substrate type, even a relatively large void does not alter the TSV resistance or its parasitic capacitance noticeably at 1GHz solution frequency. An on-chip test solution for TSV parametric faults requires a dedicated high resolution measurement circuit due to the minor variations of TSV circuit model parameters

Optimizing the integration and energy efficiency of through silicon via-based 3D interconnects

The aggressive scaling of CMOS process technology has been driving the rapid growth of the semiconductor industry for more than three decades. In recent years, the performance gains enabled by CMOS scaling have been increasingly challenged by highlyparasitic on-chip interconnects as wire parasitics do not scale at the same pace. Emerging 3D integration technologies based on vertical through-silicon vias (TSVs) promise a solution to the interconnect performance bottleneck, along with reduced fabrication cost and heterogeneous integration. As TSVs are a relatively recent interconnect technology, innovative test structures are required to evaluate and optimise the process, as well as extract parameters for the generation of design rules and models. From the circuit designer’s perspective, critical TSV characteristics are its parasitic capacitance, and thermomechanical stress distribution. This work proposes new test structures for extracting these characteristics. The structures were fabricated on a 65nm 3D process and used for the evaluation of that technology. Furthermore, as TSVs are implemented in large, densely interconnected 3D-system-on-chips (SoCs), the TSV parasitic capacitance may become an important source of energy dissipation. Typical low-power techniques based on voltage scaling can be used, though this represents a technical challenge in modern technology nodes. In this work, a novel TSV interconnection scheme is proposed based on reversible computing, which shows frequencydependent energy dissipation. The scheme is analysed using theoretical modelling, while a demonstrator IC was designed based on the developed theory and fabricated on a 130nm 3D process.EThOS - Electronic Theses Online ServiceEngineering and Physical Science Research Council (EPSRC)GBUnited Kingdo

Design-for-Test and Test Optimization Techniques for TSV-based 3D Stacked ICs

<p>As integrated circuits (ICs) continue to scale to smaller dimensions, long interconnects</p><p>have become the dominant contributor to circuit delay and a significant component of</p><p>power consumption. In order to reduce the length of these interconnects, 3D integration</p><p>and 3D stacked ICs (3D SICs) are active areas of research in both academia and industry.</p><p>3D SICs not only have the potential to reduce average interconnect length and alleviate</p><p>many of the problems caused by long global interconnects, but they can offer greater design</p><p>flexibility over 2D ICs, significant reductions in power consumption and footprint in</p><p>an era of mobile applications, increased on-chip data bandwidth through delay reduction,</p><p>and improved heterogeneous integration.</p><p>Compared to 2D ICs, the manufacture and test of 3D ICs is significantly more complex.</p><p>Through-silicon vias (TSVs), which constitute the dense vertical interconnects in a</p><p>die stack, are a source of additional and unique defects not seen before in ICs. At the same</p><p>time, testing these TSVs, especially before die stacking, is recognized as a major challenge.</p><p>The testing of a 3D stack is constrained by limited test access, test pin availability,</p><p>power, and thermal constraints. Therefore, efficient and optimized test architectures are</p><p>needed to ensure that pre-bond, partial, and complete stack testing are not prohibitively</p><p>expensive.</p><p>Methods of testing TSVs prior to bonding continue to be a difficult problem due to test</p><p>access and testability issues. Although some built-in self-test (BIST) techniques have been</p><p>proposed, these techniques have numerous drawbacks that render them impractical. In this dissertation, a low-cost test architecture is introduced to enable pre-bond TSV test through</p><p>TSV probing. This has the benefit of not needing large analog test components on the die,</p><p>which is a significant drawback of many BIST architectures. Coupled with an optimization</p><p>method described in this dissertation to create parallel test groups for TSVs, test time for</p><p>pre-bond TSV tests can be significantly reduced. The pre-bond probing methodology is</p><p>expanded upon to allow for pre-bond scan test as well, to enable both pre-bond TSV and</p><p>structural test to bring pre-bond known-good-die (KGD) test under a single test paradigm.</p><p>The addition of boundary registers on functional TSV paths required for pre-bond</p><p>probing results in an increase in delay on inter-die functional paths. This cost of test</p><p>architecture insertion can be a significant drawback, especially considering that one benefit</p><p>of 3D integration is that critical paths can be partitioned between dies to reduce their delay.</p><p>This dissertation derives a retiming flow that is used to recover the additional delay added</p><p>to TSV paths by test cell insertion.</p><p>Reducing the cost of test for 3D-SICs is crucial considering that more tests are necessary</p><p>during 3D-SIC manufacturing. To reduce test cost, the test architecture and test</p><p>scheduling for the stack must be optimized to reduce test time across all necessary test</p><p>insertions. This dissertation examines three paradigms for 3D integration - hard dies, firm</p><p>dies, and soft dies, that give varying degrees of control over 2D test architectures on each</p><p>die while optimizing the 3D test architecture. Integer linear programming models are developed</p><p>to provide an optimal 3D test architecture and test schedule for the dies in the 3D</p><p>stack considering any or all post-bond test insertions. Results show that the ILP models</p><p>outperform other optimization methods across a range of 3D benchmark circuits.</p><p>In summary, this dissertation targets testing and design-for-test (DFT) of 3D SICs.</p><p>The proposed techniques enable pre-bond TSV and structural test while maintaining a</p><p>relatively low test cost. Future work will continue to enable testing of 3D SICs to move</p><p>industry closer to realizing the true potential of 3D integration.</p>Dissertatio

VLSI Design

This book provides some recent advances in design nanometer VLSI chips. The selected topics try to present some open problems and challenges with important topics ranging from design tools, new post-silicon devices, GPU-based parallel computing, emerging 3D integration, and antenna design. The book consists of two parts, with chapters such as: VLSI design for multi-sensor smart systems on a chip, Three-dimensional integrated circuits design for thousand-core processors, Parallel symbolic analysis of large analog circuits on GPU platforms, Algorithms for CAD tools VLSI design, A multilevel memetic algorithm for large SAT-encoded problems, etc

Embedded dynamic programming networks for networks-on-chip

PhD ThesisRelentless technology downscaling and recent technological advancements in three dimensional integrated circuit (3D-IC) provide a promising prospect to realize heterogeneous system-on-chip (SoC) and homogeneous chip multiprocessor (CMP) based on the networks-onchip (NoCs) paradigm with augmented scalability, modularity and performance. In many cases in such systems, scheduling and managing communication resources are the major design and implementation challenges instead of the computing resources. Past research efforts were mainly focused on complex design-time or simple heuristic run-time approaches to deal with the on-chip network resource management with only local or partial information about the network. This could yield poor communication resource utilizations and amortize the benefits of the emerging technologies and design methods. Thus, the provision for efficient run-time resource management in large-scale on-chip systems becomes critical. This thesis proposes a design methodology for a novel run-time resource management infrastructure that can be realized efficiently using a distributed architecture, which closely couples with the distributed NoC infrastructure. The proposed infrastructure exploits the global information and status of the network to optimize and manage the on-chip communication resources at run-time. There are four major contributions in this thesis. First, it presents a novel deadlock detection method that utilizes run-time transitive closure (TC) computation to discover the existence of deadlock-equivalence sets, which imply loops of requests in NoCs. This detection scheme, TC-network, guarantees the discovery of all true-deadlocks without false alarms in contrast to state-of-the-art approximation and heuristic approaches. Second, it investigates the advantages of implementing future on-chip systems using three dimensional (3D) integration and presents the design, fabrication and testing results of a TC-network implemented in a fully stacked three-layer 3D architecture using a through-silicon via (TSV) complementary metal-oxide semiconductor (CMOS) technology. Testing results demonstrate the effectiveness of such a TC-network for deadlock detection with minimal computational delay in a large-scale network. Third, it introduces an adaptive strategy to effectively diffuse heat throughout the three dimensional network-on-chip (3D-NoC) geometry. This strategy employs a dynamic programming technique to select and optimize the direction of data manoeuvre in NoC. It leads to a tool, which is based on the accurate HotSpot thermal model and SystemC cycle accurate model, to simulate the thermal system and evaluate the proposed approach. Fourth, it presents a new dynamic programming-based run-time thermal management (DPRTM) system, including reactive and proactive schemes, to effectively diffuse heat throughout NoC-based CMPs by routing packets through the coolest paths, when the temperature does not exceed chip’s thermal limit. When the thermal limit is exceeded, throttling is employed to mitigate heat in the chip and DPRTM changes its course to avoid throttled paths and to minimize the impact of throttling on chip performance. This thesis enables a new avenue to explore a novel run-time resource management infrastructure for NoCs, in which new methodologies and concepts are proposed to enhance the on-chip networks for future large-scale 3D integration.Iraqi Ministry of Higher Education and Scientific Research (MOHESR)

Integrating specification and test requirements as constraints in verification strategies for 2D and 3D analog and mixed signal designs

Analog and Mixed Signal (AMS) designs are essential components of today’s modern Integrated Circuits (ICs) used in the interface between real world signals and the digital world. They present, however, significant verification challenges. Out-of-specification failures in these systems have steadily increased, and have reached record highs in recent years. Increasing design complexity, incomplete/wrong specifications (responsible for 47% of all non functional ICs) as well as additional challenges faced when testing these systems are obvious reasons. A particular example is the escalating impact of realistic test conditions with respect to physical (interface between the device under test (DUT) and the test instruments, input-signal conditions, input impedance, etc.), functional (noise, jitter) and environmental (temperature) constraints. Unfortunately, the impact of such constraints could result in a significant loss of performance and design failure even if the design itself was flawless. Current industrial verification methodologies, each addressing specific verification challenges, have been shown to be useful for detecting and eliminating design failures. Nevertheless, decreases in first pass silicon success rates illustrate the lack of cohesive, efficient techniques to allow a predictable verification process that leads to the highest possible confidence in the correctness of AMS designs. In this PhD thesis, we propose a constraint-driven verification methodology for monitoring specifications of AMS designs. The methodology is based on the early insertion of test(s) associated with each design specification. It exploits specific constraints introduced by these planned tests as well as by the specifications themselves, as they are extracted and used during the verification process, thus reducing the risk of costly errors caused by incomplete, ambiguous or missing details in the specification documents. To fully analyze the impact of these constraints on the overall AMS design behavior, we developed a two-phase algorithm that automatically integrates them into the AMS design behavioral model and performs the specifications monitoring in a Matlab simulation environment. The effectiveness of this methodology is demonstrated for two-dimensional (2D) and three-dimensional (3D) ICs. Our results show that our approach can predict out-of-specification failures, corner cases that were not covered using previous verification methodologies. On one hand, we show that specifications satisfied without specification and test-related constraints have failed in the presence of these additional constraints. On the other hand, we show that some specifications may degrade or even cannot be verified without adding specific specification and test-related constraints