Design of Energy-Efficient A/D Converters with Partial Embedded Equalization for High-Speed Wireline Receiver Applications

As the data rates of wireline communication links increases, channel impairments such as skin effect, dielectric loss, fiber dispersion, reflections and cross-talk become more pronounced. This warrants more interest in analog-to-digital converter (ADC)-based serial link receivers, as they allow for more complex and flexible back-end digital signal processing (DSP) relative to binary or mixed-signal receivers. Utilizing this back-end DSP allows for complex digital equalization and more bandwidth-efficient modulation schemes, while also displaying reduced process/voltage/temperature (PVT) sensitivity. Furthermore, these architectures offer straightforward design translation and can directly leverage the area and power scaling offered by new CMOS technology nodes. However, the power consumption of the ADC front-end and subsequent digital signal processing is a major issue. Embedding partial equalization inside the front-end ADC can potentially result in lowering the complexity of back-end DSP and/or decreasing the ADC resolution requirement, which results in a more energy-effcient receiver. This dissertation presents efficient implementations for multi-GS/s time-interleaved ADCs with partial embedded equalization. First prototype details a 6b 1.6GS/s ADC with a novel embedded redundant-cycle 1-tap DFE structure in 90nm CMOS. The other two prototypes explain more complex 6b 10GS/s ADCs with efficiently embedded feed-forward equalization (FFE) and decision feedback equalization (DFE) in 65nm CMOS. Leveraging a time-interleaved successive approximation ADC architecture, new structures for embedded DFE and FFE are proposed with low power/area overhead. Measurement results over FR4 channels verify the effectiveness of proposed embedded equalization schemes. The comparison of fabricated prototypes against state-of-the-art general-purpose ADCs at similar speed/resolution range shows comparable performances, while the proposed architectures include embedded equalization as well

A 10-Gb/s two-dimensional eye-opening monitor in 0.13-μm standard CMOS

An eye-opening monitor (EOM) architecture that can capture a two-dimensional (2-D) map of the eye diagram of a high-speed data signal has been developed. Two single-quadrant phase rotators and one digital-to-analog converter (DAC) are used to generate rectangular masks with variable sizes and aspect ratios. Each mask is overlapped with the received eye diagram and the number of signal transitions inside the mask is recorded as error. The combination of rectangular masks with the same error creates error contours that overall provide a 2-D map of the eye. The authors have implemented a prototype circuit in 0.13-μm standard CMOS technology that operates up to 12.5 Gb/s at 1.2-V supply. The EOM maps the input eye to a 2-D error diagram with up to 68-dB mask error dynamic range. The left and right halves of the eyes are monitored separately to capture horizontally asymmetric eyes. The chip consumes 330 mW and operates reliably with supply voltages as low as 1 V at 10 Gb/s. The authors also present a detailed analysis that verifies if the measurements are in good agreement with the expected results

Contributions to adaptive equalization and timing recovery for optical storage systems

no abstrac

최적에 가까운 타이밍 적응을 위해 치우친 데이터 레벨과 눈 경사 디텍터를 사용한 최대 눈크기추적 클럭 및 데이터 복원회로 설계

학위논문 (박사) -- 서울대학교 대학원 : 공과대학 전기·정보공학부, 2021. 2. 정덕균.이 논문에서는 최소-비트 비트 에러율 (BER)에 대한 최대 눈크기 추적 CDR (MET-CDR)의 설계가 제안되었다. 제안 된 CDR 은 최적의 샘플링 단계를 찾기 위해 반복 절차를 가진 BER 카운터 또는 아이 모니터가 필 요하지 않다. 에러 샘플러 출력에 가중치를 두어 더하여 얻은 치우친 데 이터 레벨 (biased dLev) 은 사전 커서 ISI(pre-cursor ISI) 의 정보도 고려한 눈 높이 정보를 추출한다. 델타 T 만큼의 시간 차이를 둔 지점에서 작동 하는 두 샘플러는 현재 눈 높이와 눈 기울기의 극성을 감지하고, 이 정보 를 통해 제안하는 CDR 은 눈 기울기가 0 이되는 최대 눈 높이로 수렴한 다. 측정 결과는 최대 눈 높이와 최소 BER 의 샘플링 위치가 잘 일치 함 을 보여준다. 28nm CMOS 공정으로 구현된 수신기 칩은 23.5dB 의 채널 손실이 있는 상태에서 26Gb/s 에서 동작 가능하다. 0.25UI 의 아이 오프닝 을 가지며, 87mW 의 파워를 소비한다.In this thesis, design of a maximum-eye-tracking CDR (MET-CDR) for minimum bit error rate (BER) is proposed. The proposed CDR does not require a BER coun-ter or an eye-opening monitor with any iterative procedure to find the near-optimal sampling phase. The biased data-level obtained from the weighted sum of error sampler outputs, UP and DN, extracts the actual eye height information in the presence of pre-cursor ISI. Two samplers operating on two slightly different tim-ings detect the current eye height and the polarity of the eye slope so that the CDR tracks the maximum eye height where the slope becomes zero. Measured results show that the sampling phase of the maximum eye height and that of the mini-mum BER match well. A prototype receiver fabricated in 28 nm CMOS process operates at 26 Gb/s with an eye-opening of 0.25 UI and consumes 87 mW while equalizing 23.5 dB of loss at 13 GHz.ABSTRACT I CONTENTS II LIST OF FIGURES IV LIST OF TABLES VIII CHAPTER 1 INTRODUCTION 1 1.1 MOTIVATION 1 1.2 THESIS ORGANIZATION 4 CHAPTER 2 BACKGROUNDS 5 2.1 RECEIVER FRONT-END 5 2.1.1 CHANNEL 7 2.1.2 EQUALIZER 17 2.1.3 CDR 32 2.2 PRIOR ARTS ON CLOCK RECOVERY 39 2.2.1 BB-CDR 39 2.2.2 BER-BASED CDR 41 2.2.3 EOM-BASED CDR 44 2.3 CONCEPT OF THE PROPOSED CDR 47 CHAPTER 3 MAXIMUM-EYE-TRACKING CDR WITH BIASED DATA-LEVEL AND EYE SLOPE DETECTOR 49 3.1 OVERVIEW 49 3.2 DESIGN OF MET-CDR 50 3.2.1 EYE HEIGHT INFORMATION FROM BIASED DATA-LEVEL 50 3.2.2 EYE SLOPE DETECTOR AND ADAPTATION ALGORITHM 60 3.2.3 ARCHITECTURE AND IMPLEMENTATION 67 3.2.4 VERIFICATION OF THE ALGORITHM 71 3.2.5 ANALYSIS ON THE BIASED DATA-LEVEL 76 3.3 EXPANSION OF MET-CDR TO PAM4 SIGNALING 84 3.3.1 MET-CDR WITH PAM4 84 3.3.2 CONSIDERATIONS FOR PAM4 87 CHAPTER 4 MEASUREMENT RESULTS 89 CHAPTER 5 CONCLUSION 99 APPENDIX A MATLAB CODE FOR SIMULATING RECEIVER WITH MET-CDR 100 BIBLIOGRAPHY 105 초 록 113Docto

Digital processing of signals in the presence of inter-symbol interference and additive noise

Imperial Users onl

CMOS Transmitter using Pulse-Width Modulation Pre-Emphasis achieving 33dB Loss Compensation at 5-Gb/s

A digital transmitter pre-emphasis technique is presented that is based on pulse-width modulation, instead of finite impulse response (FIR) filtering. The technique fits well to future high-speed low-voltage CMOS processes. A 0.13 /spl mu/m CMOS transmitter achieves more than 5 Gb/s (2-PAM) over 25 m of standard RG-58U low-end coaxial copper cable. The test chip compensates for up to 33 dB of channel loss at the fundamental signaling frequency (2.5 GHz), which is the highest figure compared to literature