Energy Harvesting Wireless Communications: A Review of Recent Advances

This article summarizes recent contributions in the broad area of energy harvesting wireless communications. In particular, we provide the current state of the art for wireless networks composed of energy harvesting nodes, starting from the information-theoretic performance limits to transmission scheduling policies and resource allocation, medium access and networking issues. The emerging related area of energy transfer for self-sustaining energy harvesting wireless networks is considered in detail covering both energy cooperation aspects and simultaneous energy and information transfer. Various potential models with energy harvesting nodes at different network scales are reviewed as well as models for energy consumption at the nodes.Comment: To appear in the IEEE Journal of Selected Areas in Communications (Special Issue: Wireless Communications Powered by Energy Harvesting and Wireless Energy Transfer

Optimal digital system design in deep submicron technology

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2006.Includes bibliographical references (p. 165-174).The optimization of a digital system in deep submicron technology should be done with two basic principles: energy waste reduction and energy-delay tradeoff. Increased energy resources obtained through energy waste reduction are utilized through energy-delay tradeoffs. The previous practice of obliviously pursuing performance has led to the rapid increase in energy consumption. While energy waste due to unnecessary switching could be reduced with small increases in logic complexity, leakage energy waste still remains as a major design challenge. We find that fine-grain dynamic leakage reduction (FG-DLR), turning off small subblocks for short idle intervals, is the key for successful leakage energy saving. We introduce an FG-DLR circuit technique, Leakage Biasing, which uses leakage currents themselves to bias the circuit into the minimum leakage state, and apply it to primary SRAM arrays for bitline leakage reduction (Leakage-Biased Bitlines) and to domino logic (Leakage-Biased Domino). We also introduce another FG-DLR circuit technique, Dynamic Resizing, which dynamically downsizes transistors on idle paths while maintaining the performance along active critical paths, and apply it to static CMOS circuits.(cont.) We show that significant energy reduction can be achieved at the same computation throughput and communication bandwidth by pipelining logic gates and wires. We find that energy saved by pipelining datapaths is eventually limited by latch energy overhead, leading to a power-optimal pipelining. Structuring global wires into on-chip networks provides a better environment for pipelining and leakage energy saving. We show that the energy-efficiency increase through replacement with dynamically packet-routed networks is bounded by router energy overhead. Finally, we provide a way of relaxing the peak power constraint. We evaluate the use of Activity Migration (AM) for hot spot removal. AM spreads heat by transporting computation to a different location on the die. We show that AM can be used either to increase the power that can be dissipated by a given package, or to lower the operating temperature and hence the operating energy.by Seongmoo Heo.Ph.D

Wireless body sensor networks for health-monitoring applications

This is an author-created, un-copyedited version of an article accepted for publication in Physiological Measurement. The publisher is not responsible for any errors or omissions in this version of the manuscript or any version derived from it. The Version of Record is available online at http://dx.doi.org/10.1088/0967-3334/29/11/R01

Automatic synthesis and optimization of chip multiprocessors

The microprocessor technology has experienced an enormous growth during the last decades. Rapid downscale of the CMOS technology has led to higher operating frequencies and performance densities, facing the fundamental issue of power dissipation. Chip Multiprocessors (CMPs) have become the latest paradigm to improve the power-performance efficiency of computing systems by exploiting the parallelism inherent in applications. Industrial and prototype implementations have already demonstrated the benefits achieved by CMPs with hundreds of cores.CMP architects are challenged to take many complex design decisions. Only a few of them are:- What should be the ratio between the core and cache areas on a chip?- Which core architectures to select?- How many cache levels should the memory subsystem have?- Which interconnect topologies provide efficient on-chip communication?These and many other aspects create a complex multidimensional space for architectural exploration. Design Automation tools become essential to make the architectural exploration feasible under the hard time-to-market constraints. The exploration methods have to be efficient and scalable to handle future generation on-chip architectures with hundreds or thousands of cores.Furthermore, once a CMP has been fabricated, the need for efficient deployment of the many-core processor arises. Intelligent techniques for task mapping and scheduling onto CMPs are necessary to guarantee the full usage of the benefits brought by the many-core technology. These techniques have to consider the peculiarities of the modern architectures, such as availability of enhanced power saving techniques and presence of complex memory hierarchies.This thesis has several objectives. The first objective is to elaborate the methods for efficient analytical modeling and architectural design space exploration of CMPs. The efficiency is achieved by using analytical models instead of simulation, and replacing the exhaustive exploration with an intelligent search strategy. Additionally, these methods incorporate high-level models for physical planning. The related contributions are described in Chapters 3, 4 and 5 of the document.The second objective of this work is to propose a scalable task mapping algorithm onto general-purpose CMPs with power management techniques, for efficient deployment of many-core systems. This contribution is explained in Chapter 6 of this document.Finally, the third objective of this thesis is to address the issues of the on-chip interconnect design and exploration, by developing a model for simultaneous topology customization and deadlock-free routing in Networks-on-Chip. The developed methodology can be applied to various classes of the on-chip systems, ranging from general-purpose chip multiprocessors to application-specific solutions. Chapter 7 describes the proposed model.The presented methods have been thoroughly tested experimentally and the results are described in this dissertation. At the end of the document several possible directions for the future research are proposed

A unified model for holistic power usage in cloud datacenter servers

Cloud datacenters are compute facilities formed by hundreds and thousands of heterogeneous servers requiring significant power requirements to operate effectively. Servers are composed by multiple interacting sub-systems including applications, microelectronic processors, and cooling which reflect their respective power profiles via different parameters. What is presently unknown is how to accurately model the holistic power usage of the entire server when including all these sub-systems together. This becomes increasingly challenging when considering diverse utilization patterns, server hardware characteristics, air and liquid cooling techniques, and importantly quantifying the non-electrical energy cost imposed by cooling operation. Such a challenge arises due to the need for multi-disciplinary expertise required to study server operation holistically. This work provides a unified model for capturing holistic power usage within Cloud datacenter servers. Constructed through controlled laboratory experiments, the model captures the relationship of server power usage between software, hardware, and cooling agnostic of architecture and cooling type (air and liquid). An exciting prospect is the ability to quantify the amount of non-electrical power consumed through cooling, allowing for more realistic and accurate server power profiles. This work represents the first empirically supported analysis and modeling of holistic power usage for Cloud datacenter servers, and bridges a significant gap between computer science and mechanical engineering research. Model validation through experiments demonstrates an average standard error of 3% for server power usage within both air and liquid cooled environments

Dynamic Power Management of High Performance Network on Chip

With increased density of modern System on Chip(SoC) communication between nodes has become a major problem. Network on Chip is a novel on chip communication paradigm to solve this by using highly scalable and efficient packet switched network. The addition of intelligent networking on the chip adds to the chip’s power consumption thus making management of communication power an interesting and challenging research problem. While VLSI techniques have evolved over time to enable power reduction in the circuit level, the highly dynamic nature of modern large SoC demand more than that. This dissertation explores some innovative dynamic solutions to manage the ever increasing communication power in the post sub-micron era. Today’s highly integrated SoCs require great level of cross layer optimizations to provide maximum efficiency. This dissertation aims at the dynamic power management problem from top. Starting with a system level distribution and management down to microarchitecture enhancements were found necessary to deliver maximum power efficiency. A distributed power budget sharing technique is proposed. To efficiently satisfy the established power budget, a novel flow control and throttling technique is proposed. Finally power efficiency of underlying microarchitecture is explored and novel buffer and link management techniques are developed. All of the proposed techniques yield improvement in power-performance efficiency of the NoC infrastructure

Power-constrained aware and latency-aware microarchitectural optimizations in many-core processors

As the transistor budgets outpace the power envelope (the power-wall issue), new architectural and microarchitectural techniques are needed to improve, or at least maintain, the power efficiency of next-generation processors. Run-time adaptation, including core, cache and DVFS adaptations, has recently emerged as a promising area to keep the pace for acceptable power efficiency. However, none of the adaptation techniques proposed so far is able to provide good results when we consider the stringent power budgets that will be common in the next decades, so new techniques that attack the problem from several fronts using different specialized mechanisms are necessary. The combination of different power management mechanisms, however, bring extra levels of complexity, since other factors such as workload behavior and run-time conditions must also be considered to properly allocate power among cores and threads. To address the power issue, this thesis first proposes Chrysso, an integrated and scalable model-driven power management that quickly selects the best combination of adaptation methods out of different core and uncore micro-architecture adaptations, per-core DVFS, or any combination thereof. Chrysso can quickly search the adaptation space by making performance/power projections to identify Pareto-optimal configurations, effectively pruning the search space. Chrysso achieves 1.9x better chip performance over core-level gating for multi-programmed workloads, and 1.5x higher performance for multi-threaded workloads. Most existing power management schemes use a centralized approach to regulate power dissipation. Unfortunately, the complexity and overhead of centralized power management increases significantly with core count rendering it in-viable at fine-grain time slices. The work leverages a two-tier hierarchical power manager. This solution is highly scalable with low overhead on a tiled many-core architecture with shared LLC and per-tile DVFS at fine-grain time slices. The global power is first distributed across tiles using GPM and then within a tile (in parallel across all tiles). Additionally, this work also proposes DVFS and cache-aware thread migration (DCTM) to ensure optimum per-tile co-scheduling of compatible threads at runtime over the two-tier hierarchical power manager. DCTM outperforms existing solutions by up to 12% on adaptive many-core tile processor. With the advancements in the core micro-architectural techniques and technology scaling, the performance gap between the computational component and memory component is increasing significantly (the memory-wall issue). To bridge this gap, the architecture community is pushing forward towards multi-core architecture with on-die near-memory DRAM cache memory (faster than conventional DRAM). Gigascale DRAM Caches poses a problem of how to efficiently manage the tags. The Tags-in-DRAM designs aims at efficiently co-locate tags with data, but it still suffer from high latency especially in multi-way associativity. The thesis finally proposes Tag Cache mechanism, an on-chip distributed tag caching mechanism with limited space and latency overhead to bypass the tag read operation in multi-way DRAM Caches, thereby reducing hit latency. Each Tag Cache, stored in L2, stores tag information of the most recently used DRAM Cache ways. The Tag Cache is able to exploit temporal locality of the DRAM Cache, thereby contributing to on average 46% of the DRAM Cache hits.A mesura que el consum dels transistors supera el nivell de potència desitjable es necessiten noves tècniques arquitectòniques i microarquitectòniques per millorar, o almenys mantenir, l'eficiència energètica dels processadors de les pròximes generacions. L'adaptació en temps d'execució, tant de nuclis com de les cachés, així com també adaptacions DVFS són idees que han sorgit recentment que fan preveure que sigui un àrea prometedora per mantenir un ritme d'eficiència energètica acceptable. Tanmateix, cap de les tècniques d'adaptació proposades fins ara és capaç d'oferir bons resultats si tenim en compte les restriccions estrictes de potència que seran comuns a les pròximes dècades. És convenient definir noves tècniques que ataquin el problema des de diversos fronts utilitzant diferents mecanismes especialitzats. La combinació de diferents mecanismes de gestió d'energia porta aparellada nivells addicionals de complexitat, ja que altres factors com ara el comportament de la càrrega de treball així com condicions específiques de temps d'execució també han de ser considerats per assignar adequadament la potència entre els nuclis del sistema computador. Per tractar el tema de la potència, aquesta tesi proposa en primer lloc Chrysso, una administració d'energia integrada i escalable que selecciona ràpidament la millor combinació entre diferents adaptacions microarquitectòniques. Chrysso pot buscar ràpidament l'adaptació adequada al fer projeccions òptimes de rendiment i potència basades en configuracions de Pareto, permetent així reduir de manera efectiva l'espai de cerca. Chrysso arriba a un rendiment de 1,9 sobre tècniques convencionals d'inhibició de portes amb una càrrega d'aplicacions seqüencials; i un rendiment de 1,5 quan les aplicacions corresponen a programes parla·lels. La majoria dels sistemes de gestió d'energia existents utilitzen un enfocament centralitzat per regular la dissipació d'energia. Malauradament, la complexitat i el temps d'administració s'incrementen significativament amb una gran quantitat de nuclis. En aquest treball es defineix un gestor jeràrquic de potència basat en dos nivells. Aquesta solució és altament escalable amb baix cost operatiu en una arquitectura de múltiples nuclis integrats en clústers, amb memòria caché de darrer nivell compartida a nivell de cluster, i DVFS establert en intervals de temps de gra fi a nivell de clúster. La potència global es distribueix en primer lloc a través dels clústers utilitzant GPM i després es distribueix dins un clúster (en paral·lel si es consideren tots els clústers). A més, aquest treball també proposa DVFS i migració de fils conscient de la memòria caché (DCTM) que garanteix una òptima distribució de tasques entre els nuclis. DCTM supera les solucions existents fins a un 12%. Amb els avenços en la tecnologia i les tècniques de micro-arquitectura de nuclis, la diferència de rendiment entre el component computacional i la memòria està augmentant significativament. Per omplir aquest buit, s'està avançant cap a arquitectures de múltiples nuclis amb memòries caché integrades basades en DRAM. Aquestes memòries caché DRAM a gran escala plantegen el problema de com gestionar de forma eficaç les etiquetes. Els dissenys de cachés amb dades i etiquetes juntes són un primer pas, però encara pateixen per tenir una alta latència, especialment en cachés amb un grau alt d'associativitat. En aquesta tesi es proposa l'estudi d'una tècnica anomenada Tag Cache, un mecanisme distribuït d'emmagatzematge d'etiquetes, que redueix la latència de les operacions de lectura d'etiquetes en les memòries caché DRAM. Cada Tag Cache, que resideix a L2, emmagatzema la informació de les vies que s'han accedit recentment de les memòries caché DRAM. D'aquesta manera es pot aprofitar la localitat temporal d'una caché DRAM, fet que contribueix en promig en un 46% dels encerts en les caché DRAM