Design Considerations of a Sub-50 {\mu}W Receiver Front-end for Implantable Devices in MedRadio Band

Emerging health-monitor applications, such as information transmission through multi-channel neural implants, image and video communication from inside the body etc., calls for ultra-low active power (<50${\mu}$W) high data-rate, energy-scalable, highly energy-efficient (pJ/bit) radios. Previous literature has strongly focused on low average power duty-cycled radios or low power but low-date radios. In this paper, we investigate power performance trade-off of each front-end component in a conventional radio including active matching, down-conversion and RF/IF amplification and prioritize them based on highest performance/energy metric. The analysis reveals 50${\Omega}$ active matching and RF gain is prohibitive for 50${\mu}$W power-budget. A mixer-first architecture with an N-path mixer and a self-biased inverter based baseband LNA, designed in TSMC 65nm technology show that sub 50${\mu}$W performance can be achieved up to 10Mbps (< 5pJ/b) with OOK modulation.Comment: Accepted to appear on International Conference on VLSI Design 2018 (VLSID

Tunable Balun Low-Noise Amplifier in 65nm CMOS Technology

The presented paper includes the design and implementation of a 65 nm CMOS low-noise amplifier (LNA) based on inductive source degeneration. The amplifier is realized with an active balun enabling a single-ended input which is an important requirement for low-cost system on chip implementations. The LNA has a tunable bandpass characteristics from 4.7 GHz up to 5.6 GHz and a continuously tunable gain from 22 dB down to 0 dB, which enables the required flexibility for multi-standard, multi-band receiver architectures. The gain and band tuning is realized with an optimized tunable active resistor in parallel to a tunable L-C tank amplifier load. The amplifier achieves an IIP3 linearity of -8dBm and a noise figure of 2.7 dB at the highest gain and frequency setting with a low power consumption of 10 mW. The high flexibility of the proposed LNA structure together with the overall good performance makes it well suited for future multi-standard low-cost receiver front-ends

A Fully-Integrated Reconfigurable Dual-Band Transceiver for Short Range Wireless Communications in 180 nm CMOS

© 2015 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other users, including reprinting/ republishing this material for advertising or promotional purposes, creating new collective works for resale or redistribution to servers or lists, or reuse of any copyrighted components of this work in other works.A fully-integrated reconfigurable dual-band (760-960 MHz and 2.4-2.5 GHz) transceiver (TRX) for short range wireless communications is presented. The TRX consists of two individually-optimized RF front-ends for each band and one shared power-scalable analog baseband. The sub-GHz receiver has achieved the maximum 75 dBc 3rd-order harmonic rejection ratio (HRR3) by inserting a Q-enhanced notch filtering RF amplifier (RFA). In 2.4 GHz band, a single-ended-to-differential RFA with gain/phase imbalance compensation is proposed in the receiver. A ΣΔ fractional-N PLL frequency synthesizer with two switchable Class-C VCOs is employed to provide the LOs. Moreover, the integrated multi-mode PAs achieve the output P1dB (OP1dB) of 16.3 dBm and 14.1 dBm with both 25% PAE for sub-GHz and 2.4 GHz bands, respectively. A power-control loop is proposed to detect the input signal PAPR in real-time and flexibly reconfigure the PA's operation modes to enhance the back-off efficiency. With this proposed technique, the PAE of the sub-GHz PA is improved by x3.24 and x1.41 at 9 dB and 3 dB back-off powers, respectively, and the PAE of the 2.4 GHz PA is improved by x2.17 at 6 dB back-off power. The presented transceiver has achieved comparable or even better performance in terms of noise figure, HRR, OP1dB and power efficiency compared with the state-of-the-art.Peer reviewe

A 0.1–5.0 GHz flexible SDR receiver with digitally assisted calibration in 65 nm CMOS

© 2017 Elsevier Ltd. All rights reserved.A 0.1–5.0 GHz flexible software-defined radio (SDR) receiver with digitally assisted calibration is presented, employing a zero-IF/low-IF reconfigurable architecture for both wideband and narrowband applications. The receiver composes of a main-path based on a current-mode mixer for low noise, a high linearity sub-path based on a voltage-mode passive mixer for out-of-band rejection, and a harmonic rejection (HR) path with vector gain calibration. A dual feedback LNA with “8” shape nested inductor structure, a cascode inverter-based TCA with miller feedback compensation, and a class-AB full differential Op-Amp with Miller feed-forward compensation and QFG technique are proposed. Digitally assisted calibration methods for HR, IIP2 and image rejection (IR) are presented to maintain high performance over PVT variations. The presented receiver is implemented in 65 nm CMOS with 5.4 mm2 core area, consuming 9.6–47.4 mA current under 1.2 V supply. The receiver main path is measured with +5 dB m/+5dBm IB-IIP3/OB-IIP3 and +61dBm IIP2. The sub-path achieves +10 dB m/+18dBm IB-IIP3/OB-IIP3 and +62dBm IIP2, as well as 10 dB RF filtering rejection at 10 MHz offset. The HR-path reaches +13 dB m/+14dBm IB-IIP3/OB-IIP3 and 62/66 dB 3rd/5th-order harmonic rejection with 30–40 dB improvement by the calibration. The measured sensitivity satisfies the requirements of DVB-H, LTE, 802.11 g, and ZigBee.Peer reviewedFinal Accepted Versio

Electromagnetic compatibility aware design and testing of intermodulation distortion under multiple co-located sources illumination

Current electromagnetic immunity tests mainly rely on single-frequency sources. However, the evolution of electronic systems leads to miniaturisation and low-cost solutions, in which filters are omitted in front of active non-linear components, also for efficiency reasons. As a result, intermodulation products may leak into the band of operation. The authors propose a comprehensive strategy consisting of design and test methodologies to evaluate in-the-band leakage of out-of-band undesired components, using multiple-tone excitation and relying on an anechoic chamber as test facility. The aim of this study is to demonstrate that an anechoic chamber together with a dual-source network analyser represents an optimal facility to investigate signal integrity issues owing to leakage of intermodulation products

Multi-tone EMC testing strategy for RF-devices

In low-cost miniaturized electronic systems, filters are often omitted in front of active non-linear components, potentially resulting in unwanted intermodulation products in the band of operation. Current immunity tests most often use a single-frequency source and are hence not able to capture all relevant intermodulation products. Relying on an anechoic chamber as test facility and using multiple-tone excitation from a dual-source network analyzer, we present an advanced test methodology to evaluate in-the-band leakage of out-of-band undesired frequencies. To demonstrate our approach we use a frequency-selective active textile antenna with integrated non-linear low-noise amplifier

Integrated phased array systems in silicon

Silicon offers a new set of possibilities and challenges for RF, microwave, and millimeter-wave applications. While the high cutoff frequencies of the SiGe heterojunction bipolar transistors and the ever-shrinking feature sizes of MOSFETs hold a lot of promise, new design techniques need to be devised to deal with the realities of these technologies, such as low breakdown voltages, lossy substrates, low-Q passives, long interconnect parasitics, and high-frequency coupling issues. As an example of complete system integration in silicon, this paper presents the first fully integrated 24-GHz eight-element phased array receiver in 0.18-μm silicon-germanium and the first fully integrated 24-GHz four-element phased array transmitter with integrated power amplifiers in 0.18-μm CMOS. The transmitter and receiver are capable of beam forming and can be used for communication, ranging, positioning, and sensing applications

Design of Low-Power Transmitter and Receiver Front End

This thesis focuses on the design of "RF front-end blocks" for the transmitter and receiver. The blocks include the low noise amplifier (LNA) and mixer downconversion at the receiving side, while the power amplifier includes the pre-driver circuit, and mixer up-conversion at the transmitter side. All of the blocks were designed in a 65nm design kit. The basics of these RF blocks are first described in chapters two to four. After that, the general principle of operations is then described and different topologies are discussed. In chapter 5 the proposed design is discussed. The proposed design is composed of a differential IDCS narrow band LNA, with a passive down-conversion mixer on the receiving side, designed for bluetooth low energy (BLE) applications, that operates at 2.4 GHz with a 1.2 V supply voltage. The overall conversion gain at the receiving side was found to be greater than 13 dB with a double side band noise figure of 8.3 dB having a 1 dB compression point of -11.8 dB, and with IIP3 of -2.06 dBm having a power consumption of 251 μwatts. On the transmission side, a power amplifier with a pre-driver circuit and a passive up-conversion mixer has been designed to operate at a 1.2 V supply at the frequency of operation 2.4 GHz, having overall gain of 24 dB with maximum power added efficiency of 34% when using maximum output power of 11 dBm. The Cadence virtuoso design kit was used for simulation. Additionally, the layout considerations were discussed, followed by presentation of the post-layout results and graphs, and, finally, some conclusions have been drawn