Design of robust spin-transfer torque magnetic random access memories for ultralow power high performance on-chip cache applications

Spin-transfer torque magnetic random access memories (STT-MRAMs) based on magnetic tunnel junction (MTJ) has become the leading candidate for future universal memory technology due to its potential for low power, non-volatile, high speed and extremely good endurance. However, conflicting read and write requirements exist in STT-MRAM technology because the current path during read and write operations are the same. Read and write failures of STT-MRAMs are degraded further under process variations. The focus of this dissertation is to optimize the yield of STT- MRAMs under process variations by employing device-circuit-architecture co-design techniques. A devices-to-systems simulation framework was developed to evaluate the effectiveness of the techniques proposed in this dissertation. An optimization methodology for minimizing the failure probability of 1T-1MTJ STT-MRAM bit-cell by proper selection of bit-cell configuration and access transistor sizing is also proposed. A failure mitigation technique using assistsin 1T-1MTJ STT-MRAM bit-cells is also proposed and discussed. Assist techniques proposed in this dissertation to mitigate write failures either increase the amount of current available to switch the MTJ during write or decrease the required current to switch the MTJ. These techniques achieve significant reduction in bit-cell area and write power with minimal impact on bit-cell failure probability and read power. However, the proposed write assist techniques may be less effective in scaled STT-MRAM bit-cells. Furthermore, read failures need to be overcome and hence, read assist techniques are required. It has been experimentally demonstrated that a class of materials called multiferroics can enable manipulation of magnetization using electric fields via magnetoelectric effects. A read assist technique using an MTJ structure incorporating multiferroic materials is proposed and analyzed. It was found that it is very difficult to overcome the fundamental design issues with 1T-1MTJ STT-MRAM due to the two-terminal nature of the MTJ. Hence, multi-terminal MTJ structures consisting of complementary polarized pinned layers are proposed. Analysis of the proposed MTJ structures shows significant improvement in bit-cell failures. Finally, this dissertation explores two system-level applications enabled by STT-MRAMs, and shows that device-circuit-architecture co-design of STT-MRAMs is required to fully exploit its benefits

Design and Robustness Analysis on Non-volatile Storage and Logic Circuit

By combining the flexibility of MOS logic and the non-volatility of spintronic devices, spin-MOS logic and storage circuitry offer a promising approach to implement highly integrated, power-efficient, and nonvolatile computing and storage systems. Besides the persistent errors due to process variations, however, the functional correctness of Spin-MOS circuitry suffers from additional non-persistent errors that are incurred by the randomness of spintronic device operations, i.e., thermal fluctuations. This work quantitatively investigates the impact of thermal fluctuations on the operations of two typical Spin-MOS circuitry: one transistor and one magnetic tunnel junction (1T1J) spin-transfer torque random access memory (STT-RAM) cell and a nonvolatile latch design. A new nonvolatile latch design is proposed based on magnetic tunneling junction (MTJ) devices. In the standby mode, the latched data can be retained in the MTJs without consuming any power. Two types of operation errors can occur, namely, persistent and non-persistent errors. These are quantitatively analyzed by including models for process variations and thermal fluctuations during the read and write operations. A mixture importance sampling methodology is applied to enable yield-driven design and extend its application beyond memories to peripheral circuits and logic blocks. Several possible design techniques to reduce thermal induced non-persistent error rate are also discussed

Spin-Transfer-Torque (STT) Devices for On-chip Memory and Their Applications to Low-standby Power Systems

With the scaling of CMOS technology, the proportion of the leakage power to total power consumption increases. Leakage may account for almost half of total power consumption in high performance processors. In order to reduce the leakage power, there is an increasing interest in using nonvolatile storage devices for memory applications. Among various promising nonvolatile memory elements, spin-transfer torque magnetic RAM (STT-MRAM) is identified as one of the most attractive alternatives to conventional SRAM. However, several design challenges of STT-MRAM such as shared read and write current paths, single-ended sensing, and high dynamic power are major challenges to be overcome to make it suitable for on-chip memories. To mitigate such problems, we propose a domain wall coupling based spin-transfer torque (DWCSTT) device for on-chip caches. Our proposed DWCSTT bit-cell decouples the read and the write current paths by the electrically-insulating magnetic coupling layer so that we can separately optimize read operation without having an impact on write-ability. In addition, the complementary polarizer structure in the read path of the DWCSTT device allows DWCSTT to enable self-referenced differential sensing. DWCSTT bit-cells improve the write power consumption due to the low electrical resistance of the write current path. Furthermore, we also present three different bit-cell level design techniques of Spin-Orbit Torque MRAM (SOT-MRAM) for alleviating some of the inefficiencies of conventional magnetic memories while maintaining the advantages of spin-orbit torque (SOT) based novel switching mechanism such as low write current requirement and decoupled read and write current path. Our proposed SOT-MRAM with supporting dual read/write ports (1R/1W) can address the issue of high-write latency of STT-MRAM by simultaneous 1R/1W accesses. Second, we propose a new type of SOT-MRAM which uses only one access transistor along with a Schottky diode in order to mitigate the area-overhead caused by two access transistors in conventional SOT-MRAM. Finally, a new design technique of SOT-MRAM is presented to improve the integration density by utilizing a shared bit-line structure

Stochastic Memory Devices for Security and Computing

With the widespread use of mobile computing and internet of things, secured communication and chip authentication have become extremely important. Hardware-based security concepts generally provide the best performance in terms of a good standard of security, low power consumption, and large-area density. In these concepts, the stochastic properties of nanoscale devices, such as the physical and geometrical variations of the process, are harnessed for true random number generators (TRNGs) and physical unclonable functions (PUFs). Emerging memory devices, such as resistive-switching memory (RRAM), phase-change memory (PCM), and spin-transfer torque magnetic memory (STT-MRAM), rely on a unique combination of physical mechanisms for transport and switching, thus appear to be an ideal source of entropy for TRNGs and PUFs. An overview of stochastic phenomena in memory devices and their use for developing security and computing primitives is provided. First, a broad classification of methods to generate true random numbers via the stochastic properties of nanoscale devices is presented. Then, practical implementations of stochastic TRNGs, such as hardware security and stochastic computing, are shown. Finally, future challenges to stochastic memory development are discussed

Towards Energy-Efficient and Reliable Computing: From Highly-Scaled CMOS Devices to Resistive Memories

The continuous increase in transistor density based on Moore\u27s Law has led us to highly scaled Complementary Metal-Oxide Semiconductor (CMOS) technologies. These transistor-based process technologies offer improved density as well as a reduction in nominal supply voltage. An analysis regarding different aspects of 45nm and 15nm technologies, such as power consumption and cell area to compare these two technologies is proposed on an IEEE 754 Single Precision Floating-Point Unit implementation. Based on the results, using the 15nm technology offers 4-times less energy and 3-fold smaller footprint. New challenges also arise, such as relative proportion of leakage power in standby mode that can be addressed by post-CMOS technologies. Spin-Transfer Torque Random Access Memory (STT-MRAM) has been explored as a post-CMOS technology for embedded and data storage applications seeking non-volatility, near-zero standby energy, and high density. Towards attaining these objectives for practical implementations, various techniques to mitigate the specific reliability challenges associated with STT-MRAM elements are surveyed, classified, and assessed herein. Cost and suitability metrics assessed include the area of nanomagmetic and CMOS components per bit, access time and complexity, Sense Margin (SM), and energy or power consumption costs versus resiliency benefits. In an attempt to further improve the Process Variation (PV) immunity of the Sense Amplifiers (SAs), a new SA has been introduced called Adaptive Sense Amplifier (ASA). ASA can benefit from low Bit Error Rate (BER) and low Energy Delay Product (EDP) by combining the properties of two of the commonly used SAs, Pre-Charge Sense Amplifier (PCSA) and Separated Pre-Charge Sense Amplifier (SPCSA). ASA can operate in either PCSA or SPCSA mode based on the requirements of the circuit such as energy efficiency or reliability. Then, ASA is utilized to propose a novel approach to actually leverage the PV in Non-Volatile Memory (NVM) arrays using Self-Organized Sub-bank (SOS) design. SOS engages the preferred SA alternative based on the intrinsic as-built behavior of the resistive sensing timing margin to reduce the latency and power consumption while maintaining acceptable access time

STT-MRAM characterization and its test implications

Spin torque transfer (STT)-magnetoresistive random-access memory (MRAM) has come a long way in research to meet the speed and power consumption requirements for future memory applications. The state-of-the-art STT-MRAM bit-cells employ magnetic tunnel junction (MTJ) with perpendicular magnetic anisotropy (PMA). The process repeatabil- ity and yield stability for wafer fabrication are some of the critical issues encountered in STT-MRAM mass production. Some of the yield improvement techniques to combat the e ect of process variations have been previously explored. However, little research has been done on defect oriented testing of STT-MRAM arrays. In this thesis, the author investi- gates the parameter deviation and non-idealities encountered during the development of a novel MTJ stack con guration. The characterization result provides motivation for the development of the design for testability (DFT) scheme that can help test and characterize STT-MRAM bit-cells and the CMOS peripheral circuitry e ciently. The primary factors for wafer yield degradation are the device parameter variation and its non-uniformity across the wafer due to the fabrication process non-idealities. There- fore, e ective in-process testing strategies for exploring and verifying the impact of the parameter variation on the wafer yield will be needed to achieve fabrication process opti- mization. While yield depends on the CMOS process variability, quality of the deposited MTJ lm, and other process non-idealities, test platform can enable parametric optimiza- tion and veri cation using the CMOS-based DFT circuits. In this work, we develop a DFT algorithm and implement a DFT circuit for parametric testing and prequali cation of the critical circuits in the CMOS wafer. The DFT circuit successfully replicates the electrical characteristics of MTJ devices and captures their spatial variation across the wafer with an error of less than 4%. We estimate the yield of the read sensing path by implement- ing the DFT circuit, which can replicate the resistance-area product variation up to 50% from its nominal value. The yield data from the read sensing path at di erent wafer loca- tions are analyzed, and a usable wafer radius has been estimated. Our DFT scheme can provide quantitative feedback based on in-die measurement, enabling fabrication process optimization through iterative estimation and veri cation of the calibrated parameters. Another concern that prevents mass production of STT-MRAM arrays is the defect formation in MTJ devices due to aging. Identifying manufacturing defects in the magnetic tunnel junction (MTJ) device is crucial for the yield and reliability of spin-torque-transfer (STT) magnetic random-access memory (MRAM) arrays. Several of the MTJ defects result in parametric deviations of the device that deteriorate over time. We extend our work on the DFT scheme by monitoring the electrical parameter deviations occurring due to the defect formation over time. A programmable DFT scheme was implemented for a sub-arrayin 65 nm CMOS technology to evaluate the feasibility of the test scheme. The scheme utilizes the read sense path to compare the bit-cell electrical parameters against known DFT cells characteristics. Built-in-self-test (BIST) methodology is utilized to trigger the onset of the fault once the device parameter crosses a threshold value. We demonstrate the operation and evaluate the accuracy of detection with the proposed scheme. The DFT scheme can be exploited for monitoring aging defects, modeling their behavior and optimization of the fabrication process. DFT scheme could potentially nd numerous applications for parametric characteriza- tion and fault monitoring of STT-MRAM bit-cell arrays during mass production. Some of the applications include a) Fabrication process feedback to improve wafer turnaround time, b) STT-MRAM bit-cell health monitoring, c) Decoupled characterization of the CMOS pe- ripheral circuitry such as read-sensing path and sense ampli er characterization within the STT-MRAM array. Additionally, the DFT scheme has potential applications for detec- tion of fault formation that could be utilized for deploying redundancy schemes, providing a graceful degradation in MTJ-based bit-cell array due to aging of the device, and also providing feedback to improve the fabrication process and yield learning

A Statistical STT-RAM Design View and Robust Designs at Scaled Technologies

Rapidly increased demands for memory in electronic industry and the significant technical scaling challenges of all conventional memory technologies motivated the researches on the next generation memory technology. As one promising candidate, spin-transfer torque random access memory (STT-RAM) features fast access time, high density, non-volatility, and good CMOS process compatibility. In recent years, many researches have been conducted to improve the storage density and enhance the scalability of STT-RAM, such as reducing the write current and switching time of magnetic tunneling junction (MTJ) devices. In parallel with these efforts, the continuous increasing of tunnel magneto-resistance(TMR) ratio of the MTJ inspires the development of multi-level cell (MLC) STT-RAM, which allows multiple data bits be stored in a single memory cell. Two types of MLC STT-RAM cells, namely, parallel MLC and series MLC, were also proposed. However, like all other nanoscale devices, the performance and reliability of STT-RAM cells are severely affected by process variations, intrinsic device operating uncertainties and environmental fluctuations. The storage margin of a MLC STT-RAM cell, i.e., the distinction between the lowest and highest resistance states, is partitioned into multiple segments for multi-level data representation. As a result, the performance and reliability of MLC STT-RAM cells become more sensitive to the MOS and MTJ device variations and the thermal-induced randomness of MTJ switching. In this work, we systematically analyze the impacts of CMOS and MTJ process variations, MTJ resistance switching randomness that induced by intrinsic thermal fluctuations, and working temperature changes on STT-RAM cell designs. The STT-RAM cell reliability issues in both read and write operations are first investigated. A combined circuit and magnetic simulation platform is then established to quantitatively study the persistent and non-persistent errors in STT-RAM cell operations. Then, we analyzed the extension of STT-RAM cell behaviors from SLC (single-level- cell) to MLC (multi-level- cell). On top of that, we also discuss the optimal device parameters of the MLC MTJ for the minimization of the operation error rate of the MLC STT-RAM cells from statistical design perspective. Our simulation results show that under the current available technology, series MLC STT-RAM demonstrates overwhelming benefits in the read and write reliability compared to parallel MLC STT-RAM and could potentially satisfy the requirement of commercial practices. Finally, with the detail analysis study of STT-RAM cells, we proposed several error reduction design, such as ADAMS structure, and FA-STT structure

In-memory computing with emerging memory devices: Status and outlook

Supporting data for "In-memory computing with emerging memory devices: status and outlook", submitted to APL Machine Learning