Doctor of Philosophy

dissertationOver the last decade, cyber-physical systems (CPSs) have seen significant applications in many safety-critical areas, such as autonomous automotive systems, automatic pilot avionics, wireless sensor networks, etc. A Cps uses networked embedded computers to monitor and control physical processes. The motivating example for this dissertation is the use of fault- tolerant routing protocol for a Network-on-Chip (NoC) architecture that connects electronic control units (Ecus) to regulate sensors and actuators in a vehicle. With a network allowing Ecus to communicate with each other, it is possible for them to share processing power to improve performance. In addition, networked Ecus enable flexible mapping to physical processes (e.g., sensors, actuators), which increases resilience to Ecu failures by reassigning physical processes to spare Ecus. For the on-chip routing protocol, the ability to tolerate network faults is important for hardware reconfiguration to maintain the normal operation of a system. Adding a fault-tolerance feature in a routing protocol, however, increases its design complexity, making it prone to many functional problems. Formal verification techniques are therefore needed to verify its correctness. This dissertation proposes a link-fault-tolerant, multiflit wormhole routing algorithm, and its formal modeling and verification using two different methodologies. An improvement upon the previously published fault-tolerant routing algorithm, a link-fault routing algorithm is proposed to relax the unrealistic node-fault assumptions of these algorithms, while avoiding deadlock conservatively by appropriately dropping network packets. This routing algorithm, together with its routing architecture, is then modeled in a process-algebra language LNT, and compositional verification techniques are used to verify its key functional properties. As a comparison, it is modeled using channel-level VHDL which is compiled to labeled Petri-nets (LPNs). Algorithms for a partial order reduction method on LPNs are given. An optimal result is obtained from heuristics that trace back on LPNs to find causally related enabled predecessor transitions. Key observations are made from the comparison between these two verification methodologies

MGSim - Simulation tools for multi-core processor architectures

MGSim is an open source discrete event simulator for on-chip hardware components, developed at the University of Amsterdam. It is intended to be a research and teaching vehicle to study the fine-grained hardware/software interactions on many-core and hardware multithreaded processors. It includes support for core models with different instruction sets, a configurable multi-core interconnect, multiple configurable cache and memory models, a dedicated I/O subsystem, and comprehensive monitoring and interaction facilities. The default model configuration shipped with MGSim implements Microgrids, a many-core architecture with hardware concurrency management. MGSim is furthermore written mostly in C++ and uses object classes to represent chip components. It is optimized for architecture models that can be described as process networks.Comment: 33 pages, 22 figures, 4 listings, 2 table

Design methodology and productivity improvement in high speed VLSI circuits

2017 Spring.Includes bibliographical references.To view the abstract, please see the full text of the document

Scather: programming with multi-party computation and MapReduce

We present a prototype of a distributed computational infrastructure, an associated high level programming language, and an underlying formal framework that allow multiple parties to leverage their own cloud-based computational resources (capable of supporting MapReduce [27] operations) in concert with multi-party computation (MPC) to execute statistical analysis algorithms that have privacy-preserving properties. Our architecture allows a data analyst unfamiliar with MPC to: (1) author an analysis algorithm that is agnostic with regard to data privacy policies, (2) to use an automated process to derive algorithm implementation variants that have different privacy and performance properties, and (3) to compile those implementation variants so that they can be deployed on an infrastructures that allows computations to take place locally within each participant’s MapReduce cluster as well as across all the participants’ clusters using an MPC protocol. We describe implementation details of the architecture, discuss and demonstrate how the formal framework enables the exploration of tradeoffs between the efficiency and privacy properties of an analysis algorithm, and present two example applications that illustrate how such an infrastructure can be utilized in practice.This work was supported in part by NSF Grants: #1430145, #1414119, #1347522, and #1012798

Elasticity and Petri nets

Digital electronic systems typically use synchronous clocks and primarily assume fixed duration of their operations to simplify the design process. Time elastic systems can be constructed either by replacing the clock with communication handshakes (asynchronous version) or by augmenting the clock with a synchronous version of a handshake (synchronous version). Time elastic systems can tolerate static and dynamic changes in delays (asynchronous case) or latencies (synchronous case) of operations that can be used for modularity, ease of reuse and better power-delay trade-off. This paper describes methods for the modeling, performance analysis and optimization of elastic systems using Marked Graphs and their extensions capable of describing behavior with early evaluation. The paper uses synchronous elastic systems (aka latency-tolerant systems) for illustrating the use of Petri nets, however, most of the methods can be applied without changes (except changing the delay model associated with events of the system) to asynchronous elastic systems.Peer ReviewedPostprint (author's final draft

Design of asynchronous microprocessor for power proportionality

PhD ThesisMicroprocessors continue to get exponentially cheaper for end users following Moore’s law, while the costs involved in their design keep growing, also at an exponential rate. The reason is the ever increasing complexity of processors, which modern EDA tools struggle to keep up with. This makes further scaling for performance subject to a high risk in the reliability of the system. To keep this risk low, yet improve the performance, CPU designers try to optimise various parts of the processor. Instruction Set Architecture (ISA) is a significant part of the whole processor design flow, whose optimal design for a particular combination of available hardware resources and software requirements is crucial for building processors with high performance and efficient energy utilisation. This is a challenging task involving a lot of heuristics and high-level design decisions. Another issue impacting CPU reliability is continuous scaling for power consumption. For the last decades CPU designers have been mainly focused on improving performance, but “keeping energy and power consumption in mind”. The consequence of this was a development of energy-efficient systems, where energy was considered as a resource whose consumption should be optimised. As CMOS technology was progressing, with feature size decreasing and power delivered to circuit components becoming less stable, the energy resource turned from an optimisation criterion into a constraint, sometimes a critical one. At this point power proportionality becomes one of the most important aspects in system design. Developing methods and techniques which will address the problem of designing a power-proportional microprocessor, capable to adapt to varying operating conditions (such as low or even unstable voltage levels) and application requirements in the runtime, is one of today’s grand challenges. In this thesis this challenge is addressed by proposing a new design flow for the development of an ISA for microprocessors, which can be altered to suit a particular hardware platform or a specific operating mode. This flow uses an expressive and powerful formalism for the specification of processor instruction sets called the Conditional Partial Order Graph (CPOG). The CPOG model captures large sets of behavioural scenarios for a microarchitectural level in a computationally efficient form amenable to formal transformations for synthesis, verification and automated derivation of asynchronous hardware for the CPU microcontrol. The feasibility of the methodology, novel design flow and a number of optimisation techniques was proven in a full size asynchronous Intel 8051 microprocessor and its demonstrator silicon. The chip showed the ability to work in a wide range of operating voltage and environmental conditions. Depending on application requirements and power budget our ASIC supports several operating modes: one optimised for energy consumption and the other one for performance. This was achieved by extending a traditional datapath structure with an auxiliary control layer for adaptable and fault tolerant operation. These and other optimisations resulted in a reconfigurable and adaptable implementation, which was proven by measurements, analysis and evaluation of the chip.EPSR

Survey on Lightweight Primitives and Protocols for RFID in Wireless Sensor Networks

The use of radio frequency identification (RFID) technologies is becoming widespread in all kind of wireless network-based applications. As expected, applications based on sensor networks, ad-hoc or mobile ad hoc networks (MANETs) can be highly benefited from the adoption of RFID solutions. There is a strong need to employ lightweight cryptographic primitives for many security applications because of the tight cost and constrained resource requirement of sensor based networks. This paper mainly focuses on the security analysis of lightweight protocols and algorithms proposed for the security of RFID systems. A large number of research solutions have been proposed to implement lightweight cryptographic primitives and protocols in sensor and RFID integration based resource constraint networks. In this work, an overview of the currently discussed lightweight primitives and their attributes has been done. These primitives and protocols have been compared based on gate equivalents (GEs), power, technology, strengths, weaknesses and attacks. Further, an integration of primitives and protocols is compared with the possibilities of their applications in practical scenarios