State-variable modelling of CLL resonant converters

The paper presents the derivation and application of state-variable models to high-order topologies of resonant converters. In particular, a 3rd order CLL resonant circuit is considered with bridge rectification and both a capacitive output filter (voltage output), and an LC output filter (current output). The state-variable model accuracy is verified against component-based simulation packages (Spice) and practical measurements, and it is shown that the resulting models facilitate rapid analysis compared to their integration-based counterparts (Spice, Saber), without the loss of accuracy normally associated with fundamental mode approximation (FMA) techniques. Moreover, unlike FMA, the models correctly predict the resonant peaks associated with harmonic excitation of the tank resonance. Subsequently, it is shown that excitation of the resonant tank by odd harmonics of the input voltage can be utilised to provide overcurrent protection in the event of an output short-circuit. Further, through judicious control of operating frequency, it is shown that 'inductive' zero voltage switching (ZVS) can still be obtained, facilitating reductions in gate-drive switching losses, thereby improving efficiency and thermal management of the supply under fault conditions. Although the results are ultimately generic to other converter counterparts, measured results from two prototype 36 V input, 11-14.4V output, 3rd - order CLL converters are included to practically demonstrate the attributes of the proposed analysis and control schemes

Normalized analysis and design of LCC resonant converters

Abstract—A normalization of the LCC voltage-output resonant converter performance characteristics, in terms of the tank gain at resonance and the parallel-to-series-capacitor ratio, is presented. The resulting description is subsequently used for the derivation of a design procedure that incorporates the effects of diode losses and the finite charge/discharge time of the parallel capacitor. Unlike previously reported techniques, the resulting normalized behavior of the converter is used to identify design regions to facilitate a reduction in component electrical stresses, and the use of harmonics to transfer real power. Consideration of the use of preferred component values is also given. The underlying methodology is ultimately suitable for incorporation into a software suite for use as part of a rapid interactive design tool. Both simulation results and experimental measurements from a prototype converter are included to demonstrate the attributes of the proposed analysis and design methodologies

Cyclic-averaging for high-speed analysis of resonant converters

Abstract—The paper describes the development and application of a cyclic-averaging technique for the rapid analysis of high-order resonant power converters. To provide a focus to the paper, particular emphasis is given to a 3rd-order LCC voltage output converter topology. The proposed methodology predicts steady-state voltages and currents throughout the circuit, and provides estimates of the stresses on the resonant circuit components. State-space simulations and experimental results from a 350 V-input/150 V-output converter are used to demonstrate a prediction accuracy comparable with time-domain integration-based techniques is achievable, while requiring only 1/10,000th of the computation time. In addition, a comparison with Spice simulation results shows that cyclic averaging provides commensurate predictions of voltage and current stresses on the resonant circuit components. Issues arising from the stray capacitance associated with the resonant inductor, and the corresponding sensitivity of the predicted output voltage, are also considered

Linearized large signal modeling, analysis, and control design of phase-controlled series-parallel resonant converters using state feedback

This paper proposes a linearized large signal state-space model for the fixed-frequency phase-controlled series-parallel resonant converter. The proposed model utilizes state feedback of the output filter inductor current to perform linearization. The model combines multiple-frequency and average state-space modeling techniques to generate an aggregate model with dc state variables that are relatively easier to control and slower than the fast resonant tank dynamics. The main objective of the linearized model is to provide a linear representation of the converter behavior under large signal variation which is suitable for faster simulation and large signal estimation/calculation of the converter state variables. The model also provides insight into converter dynamics as well as a simplified reduced order transfer function for PI closed-loop design. Experimental and simulation results from a detailed switched converter model are compared with the proposed state-space model output to verify its accuracy and robustness

Digital control of dual-load LCLC resonant converters

The paper proposes the analysis, design and realisation of dual-output resonant LCLC converters with independent output regulation, employing a single power stage and combined PWM and frequency control. Asymmetric switching of the power devices is used to facilitate independent control of the outputs to provide +5 V and +3.3 V from a 15 V-20 V input supply over a range of load condition

Analysis and control of dual-output LCLC resonant converters with significant leakage inductance

The analysis, design and control of fourth-order LCLC voltage-output series-parallel resonant converters for the provision of multiple regulated outputs, is described. Specifically, state-variable concepts are developed to establish operating mode boundaries with which to describe the internal behavior and the impact of output leakage inductance. The resulting models are compared with those obtained from SPICE simulations and measurements from a prototype power supply under closed loop control to verify the analysis, modeling, and control predictions

Methodologies for the design of LCC voltage-output resonant converters

Abstract: The paper presents five structured design methodologies for third-order LCC voltage output resonant converters. The underlying principle of each technique is based on an adaptation of a FMA equivalent circuit that accommodates the nonlinear behaviour of the converter. In contrast to previously published methods, the proposed methodologies explicitly incorporate the effects of the transformer magnetising inductance. Furthermore, a number of the methodologies allow the resonant-tank components to be specified at the design phase, thereby facilitating the use of standard off-the-shelf components. A procedure for sizing the filter capacitor is derived, and the use of error mapping, to identify parameter boundaries and provide the designer with a qualitative feel for the accuracy of a proposed converter design, is explored

Verification Of Non-Isolated Lcc Resonant Full Bridge Dc-Dc Converter For Solar Photovoltaic Systems

Awareness about global warming and fasting depleting fossil fuels has intensified researcher’s interest toward exploration of renewable energy resources. Among these renewable resources, photovoltaic (solar energy) is getting more attention because of its potential to be the greatest contributor of electrical energy generation. Generally DC-DC converters are used to interface solar panels with inverter which converters dc power to ac. The function of dc-dc converter is basically to step up the low dc voltage to desired higher output voltage level. Conventional switch mode dc-dc converters have problems of high switching loss and EMI. Resonant converters on the other hand have low switching loss and EMI when they operate under ZVS conditions. The aim of this research work is to explore the feasibility of a non-isolated series-parallel resonant dc-dc converter for application in PV systems. Accordingly, the working action, analysis and design procedure of series-parallel resonant full-bridge dc-dc converter is described in detail. To evaluate the performance of converter both simulation and experimental studies are carried out. First of all, converter is simulated using LT-Spice to evaluate the capability of converter to step-up dc voltage from 30V to 300V. It is shown that converter can provide desired voltage gain both for nominal and light loads with theoretical maximum efficiency up to 94%. Finally a low power laboratory prototype of the converter is built to test and evaluate the performance of the converter. The experimental results show promising performance of the converter up to 88% efficiency at 75 kHz resonance frequency. Therefore, this converter is suitable for application in PV systems where galvanic isolation is not necessary

Modeling a multilevel converter for radiography and fluoroscopy

EPE'16 ECCE Europe, 18th European Conference on Power Electronics and Applications, 5-9 september 2016, Karsruhe, GermanyIn this paper a mathematical model for a resonant multilevel converter is presented. The topology has been conceived to be used in X-ray power supplies. The power stage has been designed to minimize the resonant current throughout the input voltage range: 400V to 750V. The inverter stage is based on the series-parallel resonant topology, LCC, to include the parasitic elements of the step-up transformer. However, the introduction of an additional magnetic coupling provides a way to modify the reactive elements depending on the output powe

Analysis And Design Optimization Of Resonant Dc-dc Converters

The development in power conversion technology is in constant demand of high power efficiency and high power density. The DC-DC power conversion is an indispensable stage for numerous power supplies and energy related applications. Particularly, in PV micro-inverters and front-end converter of power supplies, great challenges are imposed on the power performances of the DC-DC converter stage, which not only require high efficiency and density but also the capability to regulate a wide variation range of input voltage and load conditions. The resonant DC-DC converters are good candidates to meet these challenges with the advantages of achieving soft switching and low EMI. Among various resonant converter topologies, the LLC converter is very attractive for its wide gain range and providing ZVS for switches from full load to zero load condition. The operation of the LLC converter is complicated due to its multiple resonant stage mechanism. A literature review of different analysis methods are presented, and it shows that the study on the LLC is still incomplete. Therefore, an operation mode analysis method is proposed, which divides the operation into six major modes based on the occurrence of resonant stages. The resonant currents, voltages and the DC gain characteristics for each mode is investigated. To obtain a thorough view of the converter behavior, the boundaries of every mode are studied, and mode distribution regarding the gain, load and frequency is presented and discussed. As this operation mode model is a precise model, an experimental prototype is designed and built to demonstrate its accuracy in operation waveforms and gain prediction. iv Since most of the LLC modes have no closed-form solutions, simplification is necessary in order to utilize this mode model in practical design. Some prior approximation methods for converter’s gain characteristics are discussed. Instead of getting an entire gain-vs.-frequency curve, we focus on peak gains, which is an important design parameters indicating the LLC’s operating limit of input voltage and switching frequency. A numerical peak gain approximation method is developed, which provide a direct way to calculate the peak gain and its corresponding load and frequency condition. The approximated results are compared with experiments and simulations, and are proved to be accurate. In addition, as PO mode is the most favorable operation mode of the LLC, its operation region is investigated and an approximation approach is developed to determine its boundary. The design optimization of the LLC has always been a difficult problem as there are many parameters affecting the design and it lacks clear design guidance in selecting the optimal resonant tank parameters. Based on the operation mode model, three optimization methods are proposed according to the design scenarios. These methods focus on minimize the conduction loss of resonant tank while maintaining the required voltage gain level, and the approximations of peak gains and PO mode boundary can be applied here to facilitate the design. A design example is presented using one of the proposed optimization methods. As a comparison, the L-C component values are reselected and tested for the same design specifications. The experiments show that the optimal design has better efficiency performance. Finally, a generalized approach for resonant converter analysis is developed. It can be implemented by computer programs or numerical analysis tools to derive the operation waveforms and DC characteristics of resonant converter