602 research outputs found
AirSync: Enabling Distributed Multiuser MIMO with Full Spatial Multiplexing
The enormous success of advanced wireless devices is pushing the demand for
higher wireless data rates. Denser spectrum reuse through the deployment of
more access points per square mile has the potential to successfully meet the
increasing demand for more bandwidth. In theory, the best approach to density
increase is via distributed multiuser MIMO, where several access points are
connected to a central server and operate as a large distributed multi-antenna
access point, ensuring that all transmitted signal power serves the purpose of
data transmission, rather than creating "interference." In practice, while
enterprise networks offer a natural setup in which distributed MIMO might be
possible, there are serious implementation difficulties, the primary one being
the need to eliminate phase and timing offsets between the jointly coordinated
access points.
In this paper we propose AirSync, a novel scheme which provides not only time
but also phase synchronization, thus enabling distributed MIMO with full
spatial multiplexing gains. AirSync locks the phase of all access points using
a common reference broadcasted over the air in conjunction with a Kalman filter
which closely tracks the phase drift. We have implemented AirSync as a digital
circuit in the FPGA of the WARP radio platform. Our experimental testbed,
comprised of two access points and two clients, shows that AirSync is able to
achieve phase synchronization within a few degrees, and allows the system to
nearly achieve the theoretical optimal multiplexing gain. We also discuss MAC
and higher layer aspects of a practical deployment. To the best of our
knowledge, AirSync offers the first ever realization of the full multiuser MIMO
gain, namely the ability to increase the number of wireless clients linearly
with the number of jointly coordinated access points, without reducing the per
client rate.Comment: Submitted to Transactions on Networkin
Four-element phased-array beamformers and a self-interference canceling full-duplex transciver in 130-nm SiGe for 5G applications at 26 GHz
This thesis is on the design of radio-frequency (RF) integrated front-end circuits for next generation 5G communication systems. The demand for higher data rates and lower latency in 5G networks can only be met using several new technologies including, but not limited to, mm-waves, massive-MIMO, and full-duplex. Use of mm-waves provides more bandwidth that is necessary for high data rates at the cost of increased attenuation in air. Massive-MIMO arrays are required to compensate for this increased path loss by providing beam steering and array gain. Furthermore, full duplex operation is desirable for improved spectrum efficiency and reduced latency. The difficulty of full duplex operation is the self-interference (SI) between transmit (TX) and receive (RX) paths. Conventional methods to suppress this interference utilize either bulky circulators, isolators, couplers or two separate antennas. These methods are not suitable for fully-integrated full-duplex massive-MIMO arrays. This thesis presents circuit and system level solutions to the issues summarized above, in the form of SiGe integrated circuits for 5G applications at 26 GHz. First, a full-duplex RF front-end architecture is proposed that is scalable to massive-MIMO arrays. It is based on blind, RF self-interference cancellation that is applicable to single/shared antenna front-ends. A high resolution RF vector modulator is developed, which is the key building block that empowers the full-duplex frontend architecture by achieving better than state-of-the-art 10-b monotonic phase control. This vector modulator is combined with linear-in-dB variable gain amplifiers and attenuators to realize a precision self-interference cancellation circuitry. Further, adaptive control of this SI canceler is made possible by including an on-chip low-power IQ downconverter. It correlates copies of transmitted and received signals and provides baseband/dc outputs that can be used to adaptively control the SI canceler. The solution comes at the cost of minimal additional circuitry, yet significantly eases linearity requirements of critical receiver blocks at RF/IF such as mixers and ADCs. Second, to complement the proposed full-duplex front-end architecture and to provide a more complete solution, high-performance beamformer ICs with 5-/6- b phase and 3-/4-b amplitude control capabilities are designed. Single-channel, separate transmitter and receiver beamformers are implemented targeting massive- MIMO mode of operation, and their four-channel versions are developed for phasedarray communication systems. Better than state-of-the-art noise performance is obtained in the RX beamformer channel, with a full-channel noise figure of 3.3 d
- …