HARDWARE ATTACK DETECTION AND PREVENTION FOR CHIP SECURITY

Hardware security is a serious emerging concern in chip designs and applications. Due to the globalization of the semiconductor design and fabrication process, integrated circuits (ICs, a.k.a. chips) are becoming increasingly vulnerable to passive and active hardware attacks. Passive attacks on chips result in secret information leaking while active attacks cause IC malfunction and catastrophic system failures. This thesis focuses on detection and prevention methods against active attacks, in particular, hardware Trojan (HT). Existing HT detection methods have limited capability to detect small-scale HTs and are further challenged by the increased process variation. We propose to use differential Cascade Voltage Switch Logic (DCVSL) method to detect small HTs and achieve a success rate of 66% to 98%. This work also presents different fault tolerant methods to handle the active attacks on symmetric-key cipher SIMON, which is a recent lightweight cipher. Simulation results show that our Even Parity Code SIMON consumes less area and power than double modular redundancy SIMON and Reversed-SIMON, but yields a higher fault -detection-failure rate as the number of concurrent faults increases. In addition, the emerging technology, memristor, is explored to protect SIMON from passive attacks. Simulation results indicate that the memristor-based SIMON has a unique power characteristic that adds new challenges on secrete key extraction

Recent Application in Biometrics

In the recent years, a number of recognition and authentication systems based on biometric measurements have been proposed. Algorithms and sensors have been developed to acquire and process many different biometric traits. Moreover, the biometric technology is being used in novel ways, with potential commercial and practical implications to our daily activities. The key objective of the book is to provide a collection of comprehensive references on some recent theoretical development as well as novel applications in biometrics. The topics covered in this book reflect well both aspects of development. They include biometric sample quality, privacy preserving and cancellable biometrics, contactless biometrics, novel and unconventional biometrics, and the technical challenges in implementing the technology in portable devices. The book consists of 15 chapters. It is divided into four sections, namely, biometric applications on mobile platforms, cancelable biometrics, biometric encryption, and other applications. The book was reviewed by editors Dr. Jucheng Yang and Dr. Norman Poh. We deeply appreciate the efforts of our guest editors: Dr. Girija Chetty, Dr. Loris Nanni, Dr. Jianjiang Feng, Dr. Dongsun Park and Dr. Sook Yoon, as well as a number of anonymous reviewers

SCAN CHAIN BASED HARDWARE SECURITY

Hardware has become a popular target for attackers to hack into any computing and communication system. Starting from the legendary power analysis attacks discovered 20 years ago to the recent Intel Spectre and Meltdown attacks, security vulnerabilities in hardware design have been exploited for malicious purposes. With the emerging Internet of Things (IoT) applications, where the IoT devices are extremely resource constrained, many proven secure but computational expensive cryptography protocols cannot be applied on such devices. Thus there is an urgent need to understand the hardware vulnerabilities and develop cost effective mitigation methods. One established field in the semiconductor and integrated circuit (IC) industry, known as IC test, has the goal of ensuring that fabricated ICs are free of manufacturing defects and perform the required functionalities. Testing is essential to isolate faulty chips from good ones. The concept of design for test (DFT) has been integrated in the commercial IC design and fabrication process for several decades. Scan chain, which provides test engineer access to all the flip flops in the chip through the scan in (SI) and scan out (SO) ports, is the backbone of industrial testing methods and can be found in almost all the modern designs. In addition to IC testing, scan chain has found applications in intellectual property (IP) protection and IC identification. However, attackers can also leverage the controllability and observability of scan chain as a side channel to break systems such as cryptographic chips. This dissertation addresses these two important security problems by proposing (1) a practical scan chain based security primitive for IP protection and (2) a partial scan chain framework that can mitigate all the existing scan based attacks. First, we observe the fact that each D-flip-flop has two output ports, Q and Q’, designed to simplify the logic and has been used to reduce the power consumption for IC test. The availability of both Q and Q’ ports provide the opportunity for IP protection. More specifically, we can generate a digital fingerprint by selecting different connection styles between adjacent scan cells during the design of scan chain. This method has two major advantages: fingerprints are created as a post-silicon procedure and therefore there will be little fabrication overhead; altering the connection style requires the modification of test vectors for each fingerprinted IP and thus enables a non-intrusive fingerprint verification method. This addresses the overhead and detectability problems, two of the most challenging problems of designing practical IP fingerprinting techniques in the past two decades. Combined with the recently developed reconfigurable scan networks (RSNs) that are popular for embedded and IoT devices, we design an IC identification (ID) scheme utilizing the different connection styles. We perform experiments on standard benchmarks to demonstrate that our approach has low design overhead. We also conduct security analysis to show that such fingerprints and IC IDs are robust against various attacks. In the second part of this dissertation, we consider the scan chain side channel attack, which has been reported as one of the most severe side channel attacks to modern secure systems. We argue that the current countermeasures are restricted to the requirement of providing direct SI and SO for testing and thus suffers the vulnerability of leaving this side channel open to the attackers as well. Therefore, we propose a novel public-private partial scan chain based approach with the basic idea of removing the flip flops that store sensitive information from the scan chain. This will eliminate the scan chain side channel, but it also limits IC test. The key contribution in our proposed public-private partial scan chain design is that it can keep the full test coverage while providing security to the scan chain. This is achieved by chaining the removed flip flops into one or more private partial scan chains and adding protections to the SI and SO ports of such chains. Unlike the traditional partial scan design which not only fails to provide full fault coverage, but also incur huge overhead in test time and test vector generation time, we propose a set of techniques to ensure that the desired test vectors can be entered into the system efficiently. These techniques include test vector reordering, test vector reusing, and test vector generation based on a novel finite state machine (FSM) structure we have invented. On the other hand, to enable the test engineers the ability to observe the test output to diagnose the chip while not leaking information to the attackers, we propose two lightweight mechanisms, one based on linear feedback shift register (LFSR) and the other one based on configurable physical unclonable function (PUF). Finally, we discuss a protocol on how in-field test can be realized using our public-private partial scan chain. We conduct experiments with industrial scan design tools to demonstrate that the required hardware in our approach has negligible area overhead and gives full test coverage with reduced test time and does not need to re-generate test vectors. In sum, this dissertation focuses on the role of scan chain, a conventional design for test facility, in hardware security. We show that scan chain features can be leveraged to create practical IP protection techniques including IP watermarking and fingerprinting as well as IC identification and authentication. We also propose a novel public-private partial scan design principle to close the scan chain side channel to the attackers. Through this dissertation work, we demonstrate that it is possible to develop highly practical scan chain based techniques that can benefit both the community of IC test and hardware security

Authenticating the Sender on CAN Bus using Inimitable Physical Characteristics of the Transmitter and Channel

The Cybersecurity for the embedded systems has become a serious challenge in the recent times. Given that the embedded applications are being connected with each other and over the public internet while running the relatively fragile low-density code, they are prone to a wide range of attacks. These attack surfaces are inherent to most of the embedded applications. One such example is a modern automobile. A modern vehicle consists of a network of small electronic computers known as Electronic Control Units (ECUs), which makes possible the state-of-the art features. Because of the power of these tiny computers and the artificial intelligence, autonomous vehicles will be on the road for public use in near future. These vehicles will be connected over the internet and hence susceptible to the broad range of attacks. The problem gets worse in the automotive applications because of the presence of very weak internal networking protocols. The ECUs are connected via each other over Controller Area Network (CAN) Bus which lacks the basic security features. It does not provide the authenticity of the message sender and the payload integrity is absent as well. In this paper, we have proposed a novel idea to solve both of these problems based on the physical fingerprinting the transmitter of the message packet. Electrical devices are unique in terms of the physical fingerprints, they leave in the transmitted messages due to the material’s microstructure. This uniqueness exists in the time domain as well as the frequency domain of the signals. We have proposed various techniques to capture this uniqueness using the signal processing techniques at the message receiver side which will be able to link the received packet to the original transmitter. We have applied the Neural Network based Classifier in order to realize an Intrusion Detection System proof of concept. Our proposed idea, realized with different techniques, has been proven to be more efficient than the state-of-the art intrusion detection systems. We have analyzed the weaknesses in one of the advanced security techniques based on fingerprinting the clock behaviors of the message sender. We were able to launch the successful attack to bypass the intrusion detection system based on fingerprinting the clock behavior of the sender. Our work demonstrates the wide range of attacks: the external attacks by exploiting the in-vehicle infotainment system, internal attacks and a possible defense mechanism as well. We have summarized the possible attack vectors on our proposed idea as well with the challenges being faced for the real-world implementation.Master of Science in EngineeringComputer Engineering, College of Engineering & Computer ScienceUniversity of Michigan-Dearbornhttps://deepblue.lib.umich.edu/bitstream/2027.42/143524/1/49698122_Thesis_MT_1_0 (1).pdfDescription of 49698122_Thesis_MT_1_0 (1).pdf : Thesi

Does the online card payment system unwittingly facilitate fraud?

PhD ThesisThe research work in this PhD thesis presents an extensive investigation into the security settings of Card Not Present (CNP) financial transactions. These are the transactions which include payments performed with a card over the Internet on the websites, and over the phone. Our detailed analysis on hundreds of websites and on multiple CNP payment protocols justifies that the current security architecture of CNP payment system is not adequate enough to protect itself from fraud. Unintentionally, the payment system itself will allow an adversary to learn and exploit almost all of the security features put in place to protect the CNP payment system from fraud. With insecure modes of accepting payments, the online payment system paves the way for cybercriminals to abuse even the latest designed payment protocols like 3D Secure 2.0. We follow a structured analysis methodology which identifies vulnerabilities in the CNP payment protocols and demonstrates the impact of these vulnerabilities on the overall payment system. The analysis methodology comprises of UML diagrams and reference tables which describe the CNP payment protocol sequences, software tools which implements the protocol and practical demonstrations of the research results. Detailed referencing of the online payment specifications provides a documented link between the exploitable vulnerabilities observed in real implementations and the source of the vulnerability in the payment specifications. We use practical demonstrations to show that these vulnerabilities can be exploited in the real-world with ease. This presents a stronger impact message when presenting our research results to a nontechnical audience. This has helped to raise awareness of security issues relating to payment cards, with our work appearing in the media, radio and T

Defense in Depth of Resource-Constrained Devices

The emergent next generation of computing, the so-called Internet of Things (IoT), presents significant challenges to security, privacy, and trust. The devices commonly used in IoT scenarios are often resource-constrained with reduced computational strength, limited power consumption, and stringent availability requirements. Additionally, at least in the consumer arena, time-to-market is often prioritized at the expense of quality assurance and security. An initial lack of standards has compounded the problems arising from this rapid development. However, the explosive growth in the number and types of IoT devices has now created a multitude of competing standards and technology silos resulting in a highly fragmented threat model. Tens of billions of these devices have been deployed in consumers\u27 homes and industrial settings. From smart toasters and personal health monitors to industrial controls in energy delivery networks, these devices wield significant influence on our daily lives. They are privy to highly sensitive, often personal data and responsible for real-world, security-critical, physical processes. As such, these internet-connected things are highly valuable and vulnerable targets for exploitation. Current security measures, such as reactionary policies and ad hoc patching, are not adequate at this scale. This thesis presents a multi-layered, defense in depth, approach to preventing and mitigating a myriad of vulnerabilities associated with the above challenges. To secure the pre-boot environment, we demonstrate a hardware-based secure boot process for devices lacking secure memory. We introduce a novel implementation of remote attestation backed by blockchain technologies to address hardware and software integrity concerns for the long-running, unsupervised, and rarely patched systems found in industrial IoT settings. Moving into the software layer, we present a unique method of intraprocess memory isolation as a barrier to several prevalent classes of software vulnerabilities. Finally, we exhibit work on network analysis and intrusion detection for the low-power, low-latency, and low-bandwidth wireless networks common to IoT applications. By targeting these areas of the hardware-software stack, we seek to establish a trustworthy system that extends from power-on through application runtime

Novel Computational Methods for Integrated Circuit Reverse Engineering

Production of Integrated Circuits (ICs) has been largely strengthened by globalization. System-on-chip providers are capable of utilizing many different providers which can be responsible for a single task. This horizontal structure drastically improves to time-to-market and reduces manufacturing cost. However, untrust of oversea foundries threatens to dismantle the complex economic model currently in place. Many Intellectual Property (IP) consumers become concerned over what potentially malicious or unspecified logic might reside within their application. This logic which is inserted with the intention of causing harm to a consumer has been referred to as a Hardware Trojan (HT). To help IP consumers, researchers have looked into methods for finding HTs. Such methods tend to rely on high-level information relating to the circuit, which might not be accessible. There is a high possibility that IP is delivered in the gate or layout level. Some services and image processing methods can be leveraged to convert layout level information to gate-level, but such formats are incompatible with detection schemes that require hardware description language. By leveraging standard graph and dynamic programming algorithms a set of tools is developed that can help bridge the gap between gate-level netlist access and HT detection. To help in this endeavor this dissertation focuses on several problems associated with reverse engineering ICs. Logic signal identification is used to find malicious signals, and logic desynthesis is used to extract high level details. Each of the proposed method have their results analyzed for accuracy and runtime. It is found that method for finding logic tends to be the most difficult task, in part due to the degree of heuristic\u27s inaccuracy. With minor improvements moderate sized ICs could have their high-level function recovered within minutes, which would allow for a trained eye or automated methods to more easily detect discrepancies within a circuit\u27s design