Precise delay measurement through combinatorial logic

A high resolution circuit and method for facilitating precise measurement of on-chip delays for FPGAs for reliability studies. The circuit embeds a pulse generator on an FPGA chip having one or more groups of LUTS (the "LUT delay chain"), also on-chip. The circuit also embeds a pulse width measurement circuit on-chip, and measures the duration of the generated pulse through the delay chain. The pulse width of the output pulse represents the delay through the delay chain without any I/O delay. The pulse width measurement circuit uses an additional asynchronous clock autonomous from the main clock and the FPGA propagation delay can be displayed on a hex display continuously for testing purposes

EffiTest: Efficient Delay Test and Statistical Prediction for Configuring Post-silicon Tunable Buffers

At nanometer manufacturing technology nodes, process variations significantly affect circuit performance. To combat them, post- silicon clock tuning buffers can be deployed to balance timing bud- gets of critical paths for each individual chip after manufacturing. The challenge of this method is that path delays should be mea- sured for each chip to configure the tuning buffers properly. Current methods for this delay measurement rely on path-wise frequency stepping. This strategy, however, requires too much time from ex- pensive testers. In this paper, we propose an efficient delay test framework (EffiTest) to solve the post-silicon testing problem by aligning path delays using the already-existing tuning buffers in the circuit. In addition, we only test representative paths and the delays of other paths are estimated by statistical delay prediction. Exper- imental results demonstrate that the proposed method can reduce the number of frequency stepping iterations by more than 94% with only a slight yield loss.Comment: ACM/IEEE Design Automation Conference (DAC), June 201

Delay Measurements and Self Characterisation on FPGAs

This thesis examines new timing measurement methods for self delay characterisation of Field-Programmable Gate Arrays (FPGAs) components and delay measurement of complex circuits on FPGAs. Two novel measurement techniques based on analysis of a circuit's output failure rate and transition probability is proposed for accurate, precise and efficient measurement of propagation delays. The transition probability based method is especially attractive, since it requires no modifications in the circuit-under-test and requires little hardware resources, making it an ideal method for physical delay analysis of FPGA circuits. The relentless advancements in process technology has led to smaller and denser transistors in integrated circuits. While FPGA users benefit from this in terms of increased hardware resources for more complex designs, the actual productivity with FPGA in terms of timing performance (operating frequency, latency and throughput) has lagged behind the potential improvements from the improved technology due to delay variability in FPGA components and the inaccuracy of timing models used in FPGA timing analysis. The ability to measure delay of any arbitrary circuit on FPGA offers many opportunities for on-chip characterisation and physical timing analysis, allowing delay variability to be accurately tracked and variation-aware optimisations to be developed, reducing the productivity gap observed in today's FPGA designs. The measurement techniques are developed into complete self measurement and characterisation platforms in this thesis, demonstrating their practical uses in actual FPGA hardware for cross-chip delay characterisation and accurate delay measurement of both complex combinatorial and sequential circuits, further reinforcing their positions in solving the delay variability problem in FPGAs

On-Chip Delay Measurement for Degradation Detection and Its Evaluation under Accelerated Life Test

Periodical delay measurement in field is useful for not only detection of delay-related faults but also prediction of faults due to aging. Logic BIST with variable test clock generation enables on-chip delay measurement in field. This paper addresses a delay measurement scheme based on logic BIST and gives experiment results to observe aging phenomenon of test chips under accelerated life test. The measurement scheme consists of scan-based logic BIST, a variable test clock generator, and digital temperature and voltage sensors. The sensors are used to compensate measured delay values for temperature and voltage variations in field. Evaluation using SPICE simulation shows that the scheme can measure a circuit delay with resolution of 92 ps. The delay measurement scheme is also implemented on fabricated test chips with 180 nm CMOS technology and accelerated test is performed using ATE and burn-in equipment. Experimental results show that a circuit delay increased 552 ps when accelerated the chip for 3000 hours. It is confirmed that the on-chip delay measurement scheme has enough accuracy for detection of aging-induced delay increase.26th IEEE International Symposium on On-Line Testing and Robust System Design (IOLTS 2020), 13-15 July, 2020, Napoli, Italy（新型コロナ感染拡大に伴い、オンライン開催に変更

Path Delay Measurement with Correction for Temperature And Voltage Variations

Path delay measurement in field is useful for not only detection of delay-related faults but also prediction of aging-induced delay faults. In order to utilize the delay measurement results for fault detection and fault prediction, the measured delay must be corrected because the circuit delay is varied in field due to environment such as temperature or voltage variations. This paper proposes a method of BIST-based path delay measurement in which the influence of environmental variations is eliminated. An on-chip sensor measures temperature and voltage during delay measurement. Using information from the temperature and voltage sensor and pre-computed temperature and voltage sensitivities of the circuit delay, the measured delay value is corrected to a delay value that would be obtained under a fixed temperature and voltage. Evaluation for a test chip with 65nm CMOS technology implementing the proposed method shows that errors of measured delays brought by environmental variations could be reduced from 2419 to 211 ps in the range of 30 to 80 °C and 1.05 to 1.35 V. This paper also discusses application and feasibility for degradation detection of the proposed method.International Test Conference in Asia (ITC-Asia 2020), September 23-25, 2020, Taipei City, Taiwan（現地およびオンラインで開催

Temperature and Voltage Estimation Using Ring-Oscillator-Based Monitor for Field Test

Field test is performed in diverse environments, in which temperature varies across a wide range. As temperature affects a circuit delay greatly, accurate temperature monitors are required. They should be placed at various locations on a chip including hot spots. This paper proposes a flexible ring-oscillator-based monitor that accurately measures voltage as well as temperature at the same time. The measurement accuracy was confirmed by circuit simulation for 180 nm, 90 nm and 45 nm technologies. An experiment using test chips with 180 nm technology shows its feasibility.2014 IEEE 23rd Asian Test Symposium (ATS), 16-19 Nov. 2014, Hangzhou, Chin

Reconfigurable time interval measurement circuit incorporating a programmable gain time difference amplifier

PhD ThesisAs further advances are made in semiconductor manufacturing technology the performance of circuits is continuously increasing. Unfortunately, as the technology node descends deeper into the nanometre region, achieving the potential performance gain is becoming more of a challenge; due not only to the effects of process variation but also to the reduced timing margins between signals within the circuit creating timing problems. Production Standard Automatic Test Equipment (ATE) is incapable of performing internal timing measurements due, first to the lack of accessibility and second to the overall timing accuracy of the tester which is grossly inadequate. To address these issue ‘on-chip’ time measurement circuits have been developed in a similar way that built in self-test (BIST) evolved for ‘on-chip’ logic testing. This thesis describes the design and analysis of three time amplifier circuits. The analysis undertaken considers the operational aspects related to gain and input dynamic range, together with the robustness of the circuits to the effects of process, voltage and temperature (PVT) variations. The design which had the best overall performance was subsequently compared to a benchmark design, which used the ‘buffer delay offset’ technique for time amplification, and showed a marked 6.5 times improvement on the dynamic range extending this from 40 ps to 300ps. The new design was also more robust to the effects of PVT variations. The new time amplifier design was further developed to include an adjustable gain capability which could be varied in steps of approximately 7.5 from 4 to 117. The time amplifier was then connected to a 32-stage tapped delay line to create a reconfigurable time measurement circuit with an adjustable resolution range from 15 down to 0.5 ps and a dynamic range from 480 down to 16 ps depending upon the gain setting. The overall footprint of the measurement circuit, together with its calibration module occupies an area of 0.026 mm2 The final circuit, overall, satisfied the main design criteria for ‘on-chip’ time measurement circuitry, namely, it has a wide dynamic range, high resolution, robust to the effects of PVT and has a small area overhead.Umm Al-Qura University

Product assurance technology for procuring reliable, radiation-hard, custom LSI/VLSI electronics

Advanced measurement methods using microelectronic test chips are described. These chips are intended to be used in acquiring the data needed to qualify Application Specific Integrated Circuits (ASIC's) for space use. Efforts were focused on developing the technology for obtaining custom IC's from CMOS/bulk silicon foundries. A series of test chips were developed: a parametric test strip, a fault chip, a set of reliability chips, and the CRRES (Combined Release and Radiation Effects Satellite) chip, a test circuit for monitoring space radiation effects. The technical accomplishments of the effort include: (1) development of a fault chip that contains a set of test structures used to evaluate the density of various process-induced defects; (2) development of new test structures and testing techniques for measuring gate-oxide capacitance, gate-overlap capacitance, and propagation delay; (3) development of a set of reliability chips that are used to evaluate failure mechanisms in CMOS/bulk: interconnect and contact electromigration and time-dependent dielectric breakdown; (4) development of MOSFET parameter extraction procedures for evaluating subthreshold characteristics; (5) evaluation of test chips and test strips on the second CRRES wafer run; (6) two dedicated fabrication runs for the CRRES chip flight parts; and (7) publication of two papers: one on the split-cross bridge resistor and another on asymmetrical SRAM (static random access memory) cells for single-event upset analysis

High-freequency CMOS VLSI chip testability and on-chip interconnect modeling

As high-speed digital and radio-frequency mixed-signal integrated circuits become increasingly common in product designs in industry, it is important for VLSI designers to be familiar with the challenges of chip testing and the behavior of circuit elements, including on-chip interconnect, at high frequencies. Expensive, specialized test equipment and software simulation packages for high-frequency chip testing and design are not always accessible for student research. This thesis documents the setup and characterization of a best-possible environment for high-frequency chip testing and data acquisition using existing laboratory equipment and resources. Experimental methodologies and measurement results of on-chip interconnect signal integrity and delay, ring oscillator noise and timing jitter, and time-domain reflectometry (TDR) testing are presented. Methods of modeling on-chip interconnect at high frequencies using field solvers and equivalent circuits are discussed. Lastly, the designs of single-ended and differential ring oscillators, for use in future voltage-controlled oscillator (VCO) and phase-locked loop (PLL) test chip designs, are presented and analyzed