Design and Implementation of a Wireless Charging-Based Cardiac Monitoring System Focused on Temperature Reduction and Robust Power Transfer Efficiency

Wireless power transfer systems are increasingly used as a means of charging implantable medical devices. However, the heat or thermal radiation from the wireless power transfer system can be harmful to biological tissue. In this research, we designed and implemented a wireless power transfer system-based implantable medical device with low thermal radiation, achieving 44.5% coil-to-coil efficiency. To suppress thermal radiation from the transmitting coil during charging, we minimized the ESR value of the transmitting coil. To increase power transfer efficiency, a ferrite film was applied on the receiving part. Based on analyses, we fabricated a cardiac monitoring system with dimensions of 17 x 24 x 8 mm(3) and implanted it in a rat. We confirmed that the temperature of the wireless charging device increased by only 2 degrees C during the 70 min charging, which makes it safe enough to use as an implantable medical device charging system.11Ysciescopu

Embedded passive components for improved power plane decoupling

In this paper, a detailed power integrity study is described that compares the behavior of surface-mount devices and embedded components for power decoupling. Through measurements and simulations, it is found that when the layer count of the board is low, there is no significant difference between both technologies. When the number of layers increases, the short connection for the embedded components is clearly superior to the surface-mount capacitor. The resonance frequencies for the embedded capacitor do not change significantly with the increased layer count. The case with the surface-mount capacitor however, shows a large increase in parasitic inductance due to the long vias through the board

Multiplexed dispersive readout of superconducting phase qubits

We introduce a frequency-multiplexed readout scheme for superconducting phase qubits. Using a quantum circuit with four phase qubits, we couple each qubit to a separate lumped-element superconducting readout resonator, with the readout resonators connected in parallel to a single measurement line. The readout resonators and control electronics are designed so that all four qubits can be read out simultaneously using frequency multiplexing on the one measurement line. This technology provides a highly efficient and compact means for reading out multiple qubits, a significant advantage for scaling up to larger numbers of qubits.Comment: 4 pages, 4 figure

Superconducting microstrip amplifiers with sub-Kelvin noise temperature near 4 GHz

We present measurements of an amplifier operating at 3.8 GHz with 150 MHz of bandwidth based on the microstrip input-coil resonance of a dc superconducting quantum interference device (SQUID) with submicron Josephson junctions. The noise temperature is measured using two methods: comparing the signal-to-noise ratio of the system with and without the SQUID in the amplifier chain, and using a modified Y-factor technique where calibrated narrowband noise is mixed up to the SQUID amplifier operating frequency. With the SQUID cooled to 0.35 K we observe a minimum system noise temperature of 0.55 $\pm~0.13$ K, dominated by the contribution from the SQUID amplifier

Fabrication and characterization of superconducting circuit QED devices for quantum computation

We present fabrication and characterization procedures of devices for circuit quantum electrodynamics (cQED). We have made 3 GHz cavities with quality factors in the range 10^4--10^6, which allow access to the strong coupling regime of cQED. The cavities are transmission line resonators made by photolithography. They are coupled to the input and output ports via gap capacitors. An Al-based Cooper pair box is made by ebeam lithography and Dolan bridge double-angle evaporation in superconducting resonators with high quality factor. An important issue is to characterize the quality factor of the resonators. We present an RF-characterization of superconducting resonators as a function of temperature and magnetic field. We have realized different versions of the system with different box-cavity couplings by using different dielectrics and by changing the box geometry. Moreover, the cQED approach can be used as a diagnostic tool of qubit internal losses.Comment: 4 pages, 6 figures, Applied Superconductivity Conference 200

In-situ measurement of the permittivity of helium using microwave NbN resonators

By measuring the electrical transport properties of superconducting NbN quarter-wave resonators in direct contact with a helium bath, we have demonstrated a high-speed and spatially sensitive sensor for the permittivity of helium. In our implementation a $\sim10^{-3}$ mm$^3$ sensing volume is measured with a bandwidth of 300 kHz in the temperature range 1.8 to 8.8 K. The minimum detectable change of the permittivity of helium is calculated to be $\sim6\times$$10^{-11}$ $\epsilon_0$/Hz$^{1/2}$ with a sensitivity of order $10^{-13}$ $\epsilon_0$/Hz$^{1/2}$ easily achievable. Potential applications include operation as a fast, localized helium thermometer and as a transducer in superfluid hydrodynamic experiments.Comment: 4 pages, 3 figure

Convergence acceleration and accuracy improvement in power bus impedance calculation with a fast algorithm using cavity modes

Based on the cavity-mode model, we have developed a fast algorithm for calculating power bus impedance in multilayer printed circuit boards. The fast algorithm is based on a closed-form expression for the impedance Z matrix of a rectangular power bus structure; this expression was obtained by reducing the original double infinite series into a single infinite series under an approximation. The convergence of the single series is further accelerated analytically. The accelerated single summation enables much faster computation, since use of only a few terms is enough to obtain good accuracy. In addition, we propose two ways to compensate for the error due to the approximation involved in the process of reducing the double series to the single series, and have demonstrated that these two techniques are almost equivalent