Communication Subsystems for Emerging Wireless Technologies

The paper describes a multi-disciplinary design of modern communication systems. The design starts with the analysis of a system in order to define requirements on its individual components. The design exploits proper models of communication channels to adapt the systems to expected transmission conditions. Input filtering of signals both in the frequency domain and in the spatial domain is ensured by a properly designed antenna. Further signal processing (amplification and further filtering) is done by electronics circuits. Finally, signal processing techniques are applied to yield information about current properties of frequency spectrum and to distribute the transmission over free subcarrier channels

Fractional-Order Asymptotical Phase Shifter With Flat Magnitude Response

This work deals with design of fractional-order asymptotical phase shifter having constant magnitude response within almost three decades (100 Hz – 100 kHz) and frequency dependent phase difference going from 0 to 45 degrees. PSpice simulations employing macromodels of off-the-shelf active parts brought the results suitable for brief analysis of the complete solution of our phase shifter in both frequency and time domain. Magnitude flatness with only ±0.3 dB variation and maximal phase error in the middle of operational bandwidth 3.7 degrees prove very good performance of designed circuit

Low power class-AB VCII with extended dynamic range

voltage swing both at the X terminal and at the Z terminal. The VCII consists of a regulated common gate configuration at the Y current input terminal and a class-AB complementary-MOS closed loop output voltage follower that ensures the voltage buffering action between the voltage input X and the voltage output Z terminals. Spice simulation results using AMS 0.35 μm with a ±0.9 V supply voltage are provided to demonstrate the validity of the proposed topology. With a total power consumption of 28 μW, the VCII achieves a voltage swing at the X terminal of ±0.8 V, whereas a ±0.72 V is achieved on the Z terminal. Simulation results for DC and AC voltage and current gains are given, as well as harmonic distortions and noise figures. A final comparison table is also presented, where the proposed VCII is compared with other solutions presented in the literature

Integrated realizations of reconfigurable low pass and band pass filters for wide band multi-mode receivers

With the explosive development of wireless communication systems the specifications of the supporting hardware platforms have become more and more demanding. According to the long term goals of the industry, future communications systems should integrate a wide variety of standards. This leads to the idea of software defined radio, implemented on fully reconfigurable hardware.Among other reconfigurable hardware blocks, suitable for the software radio concept, an outstanding importance belongs to the reconfigurable filters that are responsible for the selectivity of the system. The problematic of filtering is strictly connected to the architecture chosen for a multi-mode receiver realization. According to the chosen architecture, the filters can exhibit low pass or band pass frequency responses.The idea of reconfigurable frequency parameters has been introduced since the beginning of modern filtering applications due to the required precision of the frequency response. However, the reconfiguration of the parameters was usually done in a limited range around ideal values. The purpose of the presented research is to transform the classical filter structures with simple self-correction into fully reconfigurable filters over a wide range of frequencies. The ideal variation of the frequency parameters is continuous and consequently difficult to implement in real circuits. Therefore, it is usually sufficient to use a discrete programming template with reasonably small steps.There are several methods to implement variable frequency parameters. The most often used programming templates employ resistor and capacitor arrays, switched according to a given code. The low pass filter implementation proposed in this work uses a special switching template, optimized for a quasi-linear frequency variation over logarithmic axes. The template also includes the possibility to compensate errors caused by component tolerances and temperature. Another important topic concerns the implementation of programmable band pass filters, suitable for IF sampling receivers. The discussion is centered on the feasibility and the flexibility of different band pass filter architectures. Due to the high frequency requirements, the emphasis lays on filters that employ transconductance amplifiers and capacitors.Die rasch fortschreitende Entwicklung drahtloser Kommunikationssysteme führt zu immer anspruchsvolleren Spezifikationen der diese Systeme unterstützenden Hardwareplattformen. Zukünftige Kommunikationssysteme sollen übereinstimmend mit den längerfristigen Zielen der Industrie verschiedene Standards integrieren. Dies führt zu der Idee von vollständig rekonfigurierbarer Hardware, welche mittels Software gesteuert wird.Inmitten anderer rekonfigurierbarer Hardwareblöcke, die für das Software Radio Konzept geeignet sind, besitzen die steuerbaren Filter, welche wesentlichen Einfluss auf die Selektivität des Systems haben, eine enorme Bedeutung. Die Filterproblematik ist eng mit der gewählten Architektur der standardübergreifenden Empfängerrealisierung verknüpft. Die Filter können entsprechend der ausgesuchten Architektur Tiefpass- oder Bandpasscharakter annehmen.Die Idee rekonfigurierbarer Frequenzparameter wurde bereits mit Beginn moderner Filteranwendungen auf Grund geforderter Frequenzganggenauigkeit umgesetzt. Jedoch wurde die Parameterrekonfiguration üblicherweise nur in einem begrenzten Bereich um die Idealwerte herum vorgenommen. Das Ziel der vorgestellten Forschungsarbeit ist es, diese klassischen Filterstrukturen mit einfacher Selbstkorrektur in über große Frequenzbereiche voll rekonfigurierbare Filter zu transformieren. Idealerweise werden die Frequenzparameter kontinuierlich variiert weswegen sich die Implementierung in reellen Schaltkreisen als schwierig erweist. Deshalb ist es üblicherweise ausreichend, ein diskretes Steuerschema mit kleinen Schrittweiten zu verwenden.Es gibt verschiedene Methoden, variable Frequenzparameter zu implementieren. Die meisten Schemata verwenden Widerstands- und Kondensatorfelder, die entsprechend eines Kodes geschaltet werden. Die in dieser Arbeit vorgestellte Implementierung eines Tiefpassfilters nutzt ein spezielles Umschaltschema, welches für die quasi-lineare Frequenzvariation bei Darstellung über logarithmischen Axen optimiert wurde. Es beinhaltet weiterhin die Möglichkeit, Fehler zu kompensieren, die durch Bauelementtoleranzen und Temperaturschwankungen hervorgerufen werden.Ein weiteres interessantes Thema betrifft die Implementierung steuerbarer Bandpassfilter, die für Empfänger mit Zwischenfrequenzabtastung geeignet sind. Die Betrachtung beschränkt sich hierbei auf die Durchführbarkeit und Flexibilität verschiedener Bandpassfilterarchitekturen. Auf Grund hoher Frequenzanforderungen liegt der Schwerpunkt auf Filtern, die auf Transkonduktanzverstärkern und Kondensatoren basieren

Low Voltage Low Power Analogue Circuits Design

Disertační práce je zaměřena na výzkum nejběžnějších metod, které se využívají při návrhu analogových obvodů s využití nízkonapěťových (LV) a nízkopříkonových (LP) struktur. Tyto LV LP obvody mohou být vytvořeny díky vyspělým technologiím nebo také využitím pokročilých technik návrhu. Disertační práce se zabývá právě pokročilými technikami návrhu, především pak nekonvenčními. Mezi tyto techniky patří využití prvků s řízeným substrátem (bulk-driven - BD), s plovoucím hradlem (floating-gate - FG), s kvazi plovoucím hradlem (quasi-floating-gate - QFG), s řízeným substrátem s plovoucím hradlem (bulk-driven floating-gate - BD-FG) a s řízeným substrátem s kvazi plovoucím hradlem (quasi-floating-gate - BD-QFG). Práce je také orientována na možné způsoby implementace známých a moderních aktivních prvků pracujících v napěťovém, proudovém nebo mix-módu. Mezi tyto prvky lze začlenit zesilovače typu OTA (operational transconductance amplifier), CCII (second generation current conveyor), FB-CCII (fully-differential second generation current conveyor), FB-DDA (fully-balanced differential difference amplifier), VDTA (voltage differencing transconductance amplifier), CC-CDBA (current-controlled current differencing buffered amplifier) a CFOA (current feedback operational amplifier). Za účelem potvrzení funkčnosti a chování výše zmíněných struktur a prvků byly vytvořeny příklady aplikací, které simulují usměrňovací a induktanční vlastnosti diody, dále pak filtry dolní propusti, pásmové propusti a také univerzální filtry. Všechny aktivní prvky a příklady aplikací byly ověřeny pomocí PSpice simulací s využitím parametrů technologie 0,18 m TSMC CMOS. Pro ilustraci přesného a účinného chování struktur je v disertační práci zahrnuto velké množství simulačních výsledků.The dissertation thesis is aiming at examining the most common methods adopted by analog circuits' designers in order to achieve low voltage (LV) low power (LP) configurations. The capability of LV LP operation could be achieved either by developed technologies or by design techniques. The thesis is concentrating upon design techniques, especially the non–conventional ones which are bulk–driven (BD), floating–gate (FG), quasi–floating–gate (QFG), bulk–driven floating–gate (BD–FG) and bulk–driven quasi–floating–gate (BD–QFG) techniques. The thesis also looks at ways of implementing structures of well–known and modern active elements operating in voltage–, current–, and mixed–mode such as operational transconductance amplifier (OTA), second generation current conveyor (CCII), fully–differential second generation current conveyor (FB–CCII), fully–balanced differential difference amplifier (FB–DDA), voltage differencing transconductance amplifier (VDTA), current–controlled current differencing buffered amplifier (CC–CDBA) and current feedback operational amplifier (CFOA). In order to confirm the functionality and behavior of these configurations and elements, they have been utilized in application examples such as diode–less rectifier and inductance simulations, as well as low–pass, band–pass and universal filters. All active elements and application examples have been verified by PSpice simulator using the 0.18 m TSMC CMOS parameters. Sufficient numbers of simulated plots are included in this thesis to illustrate the precise and strong behavior of structures.

Realization of Integrable Low- Voltage Companding Filters for Portable System Applications

Undoubtedly, today’s integrated electronic systems owe their remarkable performance primarily to the rapid advancements of digital technology since 1970s. The various important advantages of digital circuits are: its abstraction from the physical details of the actual circuit implementation, its comparative insensitiveness to variations in the manufacturing process, and the operating conditions besides allowing functional complexity that would not be possible using analog technology. As a result, digital circuits usually offer a more robust behaviour than their analog counterparts, though often with area, power and speed drawbacks. Due to these and other benefits, analog functionality has increasingly been replaced by digital implementations. In spite of the advantages discussed above, analog components are far from obsolete and continue to be key components of modern electronic systems. There is a definite trend toward persistent and ubiquitous use of analog electronic circuits in day-to-day life. Portable electronic gadgets, wireless communications and the widespread application of RF tags are just a few examples of contemporary developments. While all of these electronic systems are based on digital circuitry, they heavily rely on analog components as interfaces to the real world. In fact, many modern designs combine powerful digital systems and complementary analog components on a single chip for cost and reliability reasons. Unfortunately, the design of such systems-on-chip (SOC) suffers from the vastly different design styles of analog and digital components. While mature synthesis tools are readily available for digital designs, there is hardly any such support for analog designers apart from wellestablished PSPICE-like circuit simulators. Consequently, though the analog part usually occupies only a small fraction of the entire die area of an SOC, but its design often constitutes a major bottleneck within the entire development process. Integrated continuous-time active filters are the class of continuous-time or analog circuits which are used in various applications like channel selection in radios, anti-aliasing before sampling, and hearing aids etc. One of the figures of merit of a filter is the dynamic range; this is the ratio of the largest to the smallest signal that can be applied at the input of the filter while maintaining certain specified performance. The dynamic range required in the filter varies with the application and is decided by the variation in strength of the desired signal as well as that of unwanted signals that are to be rejected by the filter. It is well known that the power dissipation and the capacitor area of an integrated active filter increases in proportion to its dynamic range. This situation is incompatible with the needs of integrated systems, especially battery operated ones. In addition to this fundamental dependence of power dissipation on dynamic range, the design of integrated active filters is further complicated by the reduction of supply voltage of integrated circuits imposed by the scaling down of technologies to attain twin objective of higher speed and lower power consumption in digital circuits. The reduction in power consumption with decreasing supply voltage does not apply to analog circuits. In fact, considerable innovation is required with a reduced supply voltage even to avoid increasing power consumption for a given signal to noise ratio (S/N). These aspects pose a great hurdle to the active filter designer. A technique which has attracted the attention of circuit designers as a possible route to filters with higher dynamic range per unit power consumption is “companding”. Companding (compression-expansion) filters are a very promising subclass of continuous-time analog filters, where the input (linear) signal is initially compressed before it will be handled by the core (non-linear) system. In order to preserve the linear operation of the whole system, the non-linear signal produced by the core system is converted back to a linear output signal by employing an appropriate output stage. The required compression and expansion operations are performed by employing bipolar transistors in active region or MOS transistors in weak inversion; the systems thus derived are known as logarithmic-domain (logdomain) systems. In case MOS transistors operated in saturation region are employed, the derived structures are known as Square-root domain systems. Finally, the third class of companding filters can also be obtained by employing bipolar transistors in active region or MOS transistors in weak inversion; the derived systems are known as Sinh-domain systems. During the last several years, a significant research effort has been already carried out in the area of companding circuits. This is due to the fact that their main advantages are the capability for operation in low-voltage environment and large dynamic range originated from their companding nature, electronic tunability of the frequency characteristics, absence of resistors and the potential for operations in varied frequency regions.Thus, it is obvious that companding filters can be employed for implementing high-performance analog signal processing in diverse frequency ranges. For example, companding filters could be used for realizing subsystems in: xDSL modems, disk drive read channels, biomedical electronics, Bluetooth/ZigBee applications, phaselocked loops, FM stereo demodulator, touch-tone telephone tone decoder and crossover network used in a three-way high-fidelity loudspeaker etc. A number of design methods for companding filters and their building blocks have been introduced in the literature. Most of the proposed filter structures operate either above 1.5V or under symmetrical (1.5V) power supplies. According to data that provides information about the near future of semiconductor technology, International Technology Roadmap for Semiconductors (ITRS), in 2013, the supply voltage of digital circuits in 32 nm technology will be 0.5 V. Therefore, the trend for the implementation of analog integrated circuits is the usage of low-voltage building blocks that use a single 0.5-1.5V power supply. Therefore, the present investigation was primarily concerned with the study and design of low voltage and low power Companding filters. The work includes the study about: the building blocks required in implementing low voltage and low power Companding filters; the techniques used to realize low voltage and low power Companding filters and their various areas of application. Various novel low voltage and low power Companding filter designs have been developed and studied for their characteristics to be applied in a particular portable area of application. The developed designs include the N-th order universal Companding filter designs, which have been reported first time in the open literature. Further, an endeavor has been made to design Companding filters with orthogonal tuning of performance parameters so that the designs can be simultaneously used for various features. The salient features of each of the developed circuit are described. Electronic tunability is one of the major features of all of the designs. Use of grounded capacitors and resistorless designs in all the cases makes the designs suitable for IC technology. All the designs operate in a low-voltage and low-power environment essential for portable system applications. Unless specified otherwise, all the investigations on these designs are based on the PSPICE simulations using model parameters of the NR100N bipolar transistors and BSIM 0.35μm/TSMC 0.25μm /TSMC 0.18μm CMOS process MOS transistors. The performance of each circuit has been validated by comparing the characteristics obtained using simulation with the results present in the open literature. The proposed designs could not be realized in silicon due to non-availability of foundry facility at the place of study. An effort has already been started to realize some of the designs in silicon and check their applicability in practical circuits. At the basic level, one of the proposed Companding filter designs was implemented using the commercially available transistor array ICs (LM3046N) and was found to verify the theoretical predictions obtained from the simulation results

Novel Bandpass Filter Design based on Synchronous Filtering

The design of high-performance low-noise bandpass filtering systems has been studied from several aspects: (1) applying the synchronous filtering idea to the development of externally linear, time-invariant filters which can be internally nonlinear and/or time-varying, (2) seeking solutions to improve the noise performance of these filters, from parameter configuration to architecture design, and (3) implementing the systems of interest as transistor level circuits and verifying their function.Particularly, the state space representations for a biquad AM mode synchronous bandpass filter and a biquad FM mode synchronous complex filter have been proposed and realized with ideal Gm-C networks and log-domain circuits. Both systems utilize the modulator-core filter-modulator architecture to synchronize the internal signal processing. The core filter in an AM mode synchronous filter has constant center frequency and time-variant bandwidth, and the terminal modulators perform amplitude modulation to maintain the system’s external linearity and input/output characteristics. An FM mode synchronous filter typically has time-invariant bandwidth and performs frequency modulation before and after the signal filtering. Depending on whether the center frequency and terminal modulating frequency vary with time, there are static and dynamic types of FM mode synchronous filters. They both have the advantage of being able to filter the high frequency input signals in a low frequency range, which greatly alleviates the design and integration challenge due to the high frequency limitation of active components. Moreover, some dynamic filters effectively suppress the injected single-tone noise and generate an output with much higher SNR in comparison to the output from a static filter that implements the same transfer function.As a variation of an AM mode synchronous bandpass filter, the system derived by removing its back end modulator has been verified to have impressive noise reduction capability when processing noisy AM signals. Furthermore, it inspired the development of a feedback filtering system, the effective bandwidth of which could be tuned by scaling the feedback signal that time varies the core filter’s instantaneous bandwidth. It further provides an innovative approach to the design of a high-Q filter with superior immunity to internal noise, using a filter with very low Q factor. Finally, a design that combines the feedback architecture and the biquad FM mode synchronous complex filter is proposed and implemented as a log-domain filtering circuit. Appealing features of this system include wide dynamic range, flexible bandwidth and center frequency tunability. Since there is a low requirement for the high-frequency performance of active components, these filters make a good fit for monolithic integration, and greatly improved immunity to in-filter noise in comparison to that of an open loop complex filter with similar external filtering capability

CMOS Hyperbolic Sine ELIN filters for low/audio frequency biomedical applications

Hyperbolic-Sine (Sinh) filters form a subclass of Externally-Linear-Internally-Non- Linear (ELIN) systems. They can handle large-signals in a low power environment under half the capacitor area required by the more popular ELIN Log-domain filters. Their inherent class-AB nature stems from the odd property of the sinh function at the heart of their companding operation. Despite this early realisation, the Sinh filtering paradigm has not attracted the interest it deserves to date probably due to its mathematical and circuit-level complexity. This Thesis presents an overview of the CMOS weak inversion Sinh filtering paradigm and explains how biomedical systems of low- to audio-frequency range could benefit from it. Its dual scope is to: consolidate the theory behind the synthesis and design of high order Sinh continuous–time filters and more importantly to confirm their micro-power consumption and 100+ dB of DR through measured results presented for the first time. Novel high order Sinh topologies are designed by means of a systematic mathematical framework introduced. They employ a recently proposed CMOS Sinh integrator comprising only p-type devices in its translinear loops. The performance of the high order topologies is evaluated both solely and in comparison with their Log domain counterparts. A 5th order Sinh Chebyshev low pass filter is compared head-to-head with a corresponding and also novel Log domain class-AB topology, confirming that Sinh filters constitute a solution of equally high DR (100+ dB) with half the capacitor area at the expense of higher complexity and power consumption. The theoretical findings are validated by means of measured results from an 8th order notch filter for 50/60Hz noise fabricated in a 0.35μm CMOS technology. Measured results confirm a DR of 102dB, a moderate SNR of ~60dB and 74μW power consumption from 2V power supply