Zero-Voltage and Zero-Current Switching Buck-Boost Converter for PV Applications

A ZVS and ZCS buck boost converter is presented for PV panel applications. The salient points are that all the switching devices are under zero-current switching during turn-on and zero-voltage switching during turn-off. The active switches in the converter undergo zero-capacitive turn-on losses unlike switches in other soft-switched topologies. The switches do not experience any over voltage/over current stress proportional to load as in resonant converters. This soft-switching technique can also be applied to other classical switched mode power converters. A detailed analysis of the converter under steady state is discussed and simulation results obtained are presented

One-cycle control of switching converters

A new large-signal nonlinear control technique is proposed to control the duty-ratio d of a switch such that in each cycle the average value of a switched variable of the switching converter is exactly equal to or proportional to the control reference in the steady-state or in a transient. One-cycle control rejects power source perturbations in one switching cycle; the average value of the switched variable follows the dynamic reference in one switching cycle; and the controller corrects switching errors in one switching cycle. There is no steady-state error nor dynamic error between the control reference and the average value of the switched variable. Experiments with a constant frequency buck converter have demonstrated the robustness of the control method and verified the theoretical predictions. This new control method is very general and applicable to all types of pulse-width-modulated, resonant-based, or soft-switched switching converters for either voltage or current control in continuous or discontinuous conduction mode. Furthermore, it can be used to control any physical variable or abstract signal that is in the form of a switched variable or can be converted to the form of a switched variable

A unified analysis of PWM converters in discontinuous modes

Three discontinuous operating modes of PWM (pulsewidth modulated) converters are considered: the discontinuous inductor current mode (DICM), the discontinuous capacitor voltage mode (DCVM), and a previously unidentified mode called the discontinuous quasi-resonant mode (DQRM). DC and small-signal AC analyses are applicable to all basic PWM converter topologies. Any particular topology is taken into account via its DC conversion ratio in the continuous conduction mode. The small-signal model is of the same order as the state-space averaged model for the continuous mode, and it offers improved predictions of the low-frequency dynamics of PWM converters in the discontinuous modes. It is shown that converters in discontinuous modes exhibit lossless damping similar to the effect of the current-mode programming

Immediate Analysis of Periodic Steady States in Switched DC-DC Converters via SPICE

The method of immediate analysis of periodic steady states in switched DC-DC converters operating in the continuous current mode is described. The initial conditions, which correspond to the periodic steady state, are found in the first step. They are used consequently for the conventional transient analysis. A special SPICE model of the converter finds automatically these initial conditions, which are then available within the transient analysis. The method works both for the well-known behavioral models of switched converters and also for models which employ complex nonlinear SPICE models of semiconductor switches

One-Quadrant Switched-Mode Power Converters

This article presents the main topics related to one-quadrant power converters. The basic topologies are analysed and a simple methodology to obtain the steady-state output-input voltage ratio is set out. A short discussion of different methods to control one-quadrant power converters is presented. Some of the reported derived topologies of one-quadrant power converters are also considered. Some topics related to one-quadrant power converters such as synchronous rectification, hard and soft commutation, and interleaved converters are discussed. Finally, a brief introduction to resonant converters is given.Comment: 25 pages, contribution to the 2014 CAS - CERN Accelerator School: Power Converters, Baden, Switzerland, 7-14 May 201

Morphing Switched-Capacitor Converters with Variable Conversion Ratio

High-voltage-gain and wide-input-range dc-dc converters are widely used in various electronics and industrial products such as portable devices, telecommunication, automotive, and aerospace systems. The two-stage converter is a widely adopted architecture for such applications, and it is proven to have a higher efficiency as compared with that of the single-stage converter. This paper presents a modular-cell-based morphing switched-capacitor (SC) converter for application as a front-end converter of the two-stage converter. The conversion ratio of this converter is flexible and variable and can be freely extended by increasing more SC modules. The varying conversion ratio is achieved through the morphing of the converter's structure corresponding to the amplitude of the input voltage. This converter is light and compact, and is highly efficient over a very wide range of input voltage and load conditions. Experimental work on a 25-W, 6-30-V input, 3.5-8.5-V output prototype, is performed. For a single SC module, the efficiency over the entire input voltage range is higher than 98%. Applied into the two-stage converter, the overall efficiency achievable over the entire operating range is 80% including the driver's loss

Linear-assisted DC/DC converters with modified current-mode control applied to photovoltaic solar systems

This article shows the proposal of a current-mode one-cycle control for linear-assisted DC/DC converters. Linearassisted DC/DC converters are structures that allow to take advantages of the two classic alternatives in the design of power supply systems: voltage linear regulators (classic NPN topology or LDO –low dropout–) and switching DC/DC converters. The current-mode one-cycle control technique is proposed in order to obtain the duty cycle of the linear-assisted converter switch. The proposed structure can provide an output with suitable load and line regulations. Thus, the paper shows the design and simulation results of the proposed current-mode one-cycle linear-assisted converter.Postprint (published version

Optimal PWM control of switched-capacitor DC/DC power converters via model transformation and enhancing control techniques

Abstract—This paper presents an efficient and effective method for an optimal pulse width modulated (PWM) control of switched-capacitor DC/DC power converters. Optimal switching instants are determined based on minimizing the output ripple magnitude, the output leakage voltage and the sensitivity of the output load voltage with respect to both the input voltage and the load resistance. This optimal PWM control strategy has several advantages over conventional PWM control strategies: 1) It does not involve a linearization, so a large signal analysis is performed. 2) It guarantees the optimality. The problem is solved via both the model transformation and the optimal enhancing control techniques. A practical example of the PWM control of a switched-capacitor DC/DC power converter is presented