Indoor wireless communications and applications

Chapter 3 addresses challenges in radio link and system design in indoor scenarios. Given the fact that most human activities take place in indoor environments, the need for supporting ubiquitous indoor data connectivity and location/tracking service becomes even more important than in the previous decades. Specific technical challenges addressed in this section are(i), modelling complex indoor radio channels for effective antenna deployment, (ii), potential of millimeter-wave (mm-wave) radios for supporting higher data rates, and (iii), feasible indoor localisation and tracking techniques, which are summarised in three dedicated sections of this chapter

Implementation Aspects of a Transmitted-Reference UWB Receiver

In this paper, we discuss the design issues of an ultra wide band (UWB) receiver targeting a single-chip CMOS implementation for low data-rate applications like ad hoc wireless sensor networks. A non-coherent transmitted reference (TR) receiver is chosen because of its small complexity compared to other architectures. After a brief recapitulation of the UWB fundamentals and a short discussion on the major differences between coherent and non-coherent receivers, we discuss issues, challenges and possible design solutions. Several simulation results obtained by means of a behavioral model are presented, together with an analysis of the trade-off between performance and complexity in an integrated circuit implementation

The Trade-off between Processing Gains of an Impulse Radio UWB System in the Presence of Timing Jitter

In time hopping impulse radio, $N_f$ pulses of duration $T_c$ are transmitted for each information symbol. This gives rise to two types of processing gain: (i) pulse combining gain, which is a factor $N_f$, and (ii) pulse spreading gain, which is $N_c=T_f/T_c$, where $T_f$ is the mean interval between two subsequent pulses. This paper investigates the trade-off between these two types of processing gain in the presence of timing jitter. First, an additive white Gaussian noise (AWGN) channel is considered and approximate closed form expressions for bit error probability are derived for impulse radio systems with and without pulse-based polarity randomization. Both symbol-synchronous and chip-synchronous scenarios are considered. The effects of multiple-access interference and timing jitter on the selection of optimal system parameters are explained through theoretical analysis. Finally, a multipath scenario is considered and the trade-off between processing gains of a synchronous impulse radio system with pulse-based polarity randomization is analyzed. The effects of the timing jitter, multiple-access interference and inter-frame interference are investigated. Simulation studies support the theoretical results.Comment: To appear in the IEEE Transactions on Communication

Pulse interspersing in static multipath chip environments for Impulse Radio communications

Communications are becoming the bottleneck in the performance of Chip Multiprocessor (CMP). To address this issue, the use of wireless communications within a chip has been proposed, since they offer a low latency among nodes and high reconfigurability. The chip scenario has the particularity that is static, and the multipath can be known a priori. Within this context, we propose in this paper a simple yet very efficient modulation technique, based on Impulse Radio-On–Off-Keying (IR-OOK), which significantly optimizes the performance in Wireless Network-on-Chip (WNoC) as well as off-chip scenarios. This technique is based on interspersing information pulses among the reflected pulses in order to reduce the time between pulses, thus increasing the data rate. We prove that the final data rate can be considerably increased without increasing the hardware complexity of the transceiver.Peer ReviewedPostprint (published version

ATM-based TH-SSMA network for multimedia PCS

Personal communications services (PCS) promise to provide a variety of information exchanges among users with any type of mobility, at any time, in any place, through any available device. To achieve this ambitious goal, two of the major challenges in the system design are: i) to provide a high-speed wireless subsystem with large capacity and acceptable quality-of-service (QoS) and ii) to design a network architecture capable of supporting multimedia traffic and various kinds of user mobility. A time-hopping spread-spectrum wireless communication system called ultra-wide bandwidth (UWB) radio is used to provide communications that are low power, high data rate, fade resistant, and relatively shadow free in a dense multipath environment. Receiver-signal processing of UWB radio is described, and performance of such communications systems, in terms of multiple-access capability, is estimated under ideal multiple-access channel conditions. A UWB-signal propagation experiment is performed using the bandwidth in excess of 1 GHz in a typical modern office building in order to characterize the UWB-signal propagation channel. The experimental results demonstrate the feasibility of the UWB radio and its robustness in a dense multipath environment. In this paper, an ATM network is used as the backbone network due to its high bandwidth, fast switching capability, flexibility, and well-developed infrastructure. To minimize the impact caused by user mobility on the system performance, a hierarchical network-control architecture is postulated. A wireless virtual circuit (WVC) concept is proposed to improve the transmission efficiency and simplify the network control in the wireless subsystem. The key advantage of this network architecture and WVC concept is that the handoff can be done locally most of the time, due to the localized behavior of PCS users.published_or_final_versio

Fundamental Limits of Wideband Localization - Part II: Cooperative Networks

The availability of positional information is of great importance in many commercial, governmental, and military applications. Localization is commonly accomplished through the use of radio communication between mobile devices (agents) and fixed infrastructure (anchors). However, precise determination of agent positions is a challenging task, especially in harsh environments due to radio blockage or limited anchor deployment. In these situations, cooperation among agents can significantly improve localization accuracy and reduce localization outage probabilities. A general framework of analyzing the fundamental limits of wideband localization has been developed in Part I of the paper. Here, we build on this framework and establish the fundamental limits of wideband cooperative location-aware networks. Our analysis is based on the waveforms received at the nodes, in conjunction with Fisher information inequality. We provide a geometrical interpretation of equivalent Fisher information for cooperative networks. This approach allows us to succinctly derive fundamental performance limits and their scaling behaviors, and to treat anchors and agents in a unified way from the perspective of localization accuracy. Our results yield important insights into how and when cooperation is beneficial.Comment: To appear in IEEE Transactions on Information Theor