Sensores passivos alimentados por transmissão de energia sem fios para aplicações de Internet das coisas

Nowadays, the Wireless Sensor Networks (WSNs) depend on the battery duration of the sensors and there is a renewed interest in creating a passive sensor network scheme in the area of Internet of Things (IoT) and space oriented WSN systems. The challenges for the future of radio communications have a twofold evolution, one being the low power consumption and, another, the adaptability and intelligent use of the available resources. Specially designed radios should be used to reduce power consumption, and adapt to the environment in a smart and e cient way. This thesis will focus on the development of passive sensors based on low power communication (backscatter) with Wireless Power Transfer (WPT) capabilities used in IoT applications. In that sense, several high order modulations for the communication will be explored and proposed in order to increase the data rate. Moreover, the sensors need to be small and cost e ective in order to be embedded in other technologies or devices. Consequently, the RF front-end of the sensors will be designed and implemented in Monolithic Microwave Integrated Circuit (MMIC).Atualmente, as redes de sensores sem fios dependem da duração da bateria e,deste modo, existe um interesse renovado em criar um esquema de rede de sensores passivos na área de internet das coisas e sistemas de redes de sensores sem fios relacionados com o espaço. Os desafios do futuro das comunicações de rádio têm uma dupla evolução, sendo um o baixo consumo de energia e, outro, a adaptação e o uso inteligente dos recursos disponíveis. Rádios diferentes dos convencionais devem ser usados para reduzir o consumo de energia e devem adaptar-se ao ambiente de forma inteligente e eficiente, de modo a que este use a menor quantidade de energia possível para estabelecer a comunicação. Esta tese incide sobre o desenvolvimento de sensores passivos baseados em comunicação de baixo consumo energético (backscatter) com recurso a transmissão de energia sem fios de modo a que possam ser usados em diferentes aplicações inseridas na internet das coisas. Nesse sentido, várias modulações de alta ordem para a comunicação backscatter serão exploradas e propostas com o objectivo de aumentar a taxa de transmissão de dados. Além disso, os sensores precisam de ser reduzidos em tamanho e económicos de modo a serem incorporados em outras tecnologias ou dispositivos. Consequentemente, o front-end de rádio frequência dos sensores será projetado e implementado em circuito integrado de microondas monolítico.Programa Doutoral em Engenharia Eletrotécnic

Energy-Efficient Wireless Circuits and Systems for Internet of Things

As the demand of ultra-low power (ULP) systems for internet of thing (IoT) applications has been increasing, large efforts on evolving a new computing class is actively ongoing. The evolution of the new computing class, however, faced challenges due to hard constraints on the RF systems. Significant efforts on reducing power of power-hungry wireless radios have been done. The ULP radios, however, are mostly not standard compliant which poses a challenge to wide spread adoption. Being compliant with the WiFi network protocol can maximize an ULP radio’s potential of utilization, however, this standard demands excessive power consumption of over 10mW, that is hardly compatible with in ULP systems even with heavy duty-cycling. Also, lots of efforts to minimize off-chip components in ULP IoT device have been done, however, still not enough for practical usage without a clean external reference, therefore, this limits scaling on cost and form-factor of the new computer class of IoT applications. This research is motivated by those challenges on the RF systems, and each work focuses on radio designs for IoT applications in various aspects. First, the research covers several endeavors for relieving energy constraints on RF systems by utilizing existing network protocols that eventually meets both low-active power, and widespread adoption. This includes novel approaches on 802.11 communication with articulate iterations on low-power RF systems. The research presents three prototypes as power-efficient WiFi wake-up receivers, which bridges the gap between industry standard radios and ULP IoT radios. The proposed WiFi wake-up receivers operate with low power consumption and remain compatible with the WiFi protocol by using back-channel communication. Back-channel communication embeds a signal into a WiFi compliant transmission changing the firmware in the access point, or more specifically just the data in the payload of the WiFi packet. With a specific sequence of data in the packet, the transmitter can output a signal that mimics a modulation that is more conducive for ULP receivers, such as OOK and FSK. In this work, low power mixer-first receivers, and the first fully integrated ultra-low voltage receiver are presented, that are compatible with WiFi through back-channel communication. Another main contribution of this work is in relieving the integration challenge of IoT devices by removing the need for external, or off-chip crystals and antennas. This enables a small form-factor on the order of mm3-scale, useful for medical research and ubiquitous sensing applications. A crystal-less small form factor fully integrated 60GHz transceiver with on-chip 12-channel frequency reference, and good peak gain dual-mode on-chip antenna is presented.PHDElectrical and Computer EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/162975/1/jaeim_1.pd

Intra-network interference robustness : an empirical evaluation of IEEE 802.15.4-2015 SUN-OFDM

While IEEE 802.15.4 and its Time Slotted Channel Hopping (TSCH) medium access mode were developed as a wireless substitute for reliable process monitoring in industrial environments, most deployments use a single/static physical layer (PHY) configuration. Instead of limiting all links to the throughput and reliability of a single Modulation and Coding Scheme (MCS), you can dynamically re-configure the PHY of link endpoints according to the context. However, such modulation diversity causes links to coincide in time/frequency space, resulting in poor reliability if left unchecked. Nonetheless, to some level, intentional spatial overlap improves resource efficiency while partially preserving the benefits of modulation diversity. Hence, we measured the mutual interference robustness of certain Smart Utility Network (SUN) Orthogonal Frequency Division Multiplexing (OFDM) configurations, as a first step towards combining spatial re-use and modulation diversity. This paper discusses the packet reception performance of those PHY configurations in terms of Signal to Interference Ratio (SIR) and time-overlap percentage between interference and targeted parts of useful transmissions. In summary, we found SUN-OFDM O3 MCS1 and O4 MCS2 performed best. Consequently, one should consider them when developing TSCH scheduling mechanisms in the search for resource efficient ubiquitous connectivity through modulation diversity and spatial re-use

Cost-Effective and Energy-Efficient Techniques for Underwater Acoustic Communication Modems

Finally, the modem developed has been tested experimentally in laboratory (aquatic environment) showing that can communicates at different data rates (100..1200 bps) compared to state-of-the-art research modems. The software used include LabVIEW, MATLAB, Simulink, and Multisim (to test the electronic circuit built) has been employed.Underwater wireless sensor networks (UWSNs) are widely used in many applications related to ecosystem monitoring, and many more fields. Due to the absorption of electromagnetic waves in water and line-of-sight communication of optical waves, acoustic waves are the most suitable medium of communication in underwater environments. Underwater acoustic modem (UAM) is responsible for the transmission and reception of acoustic signals in an aquatic channel. Commercial modems may communicate at longer distances with reliability, but they are expensive and less power efficient. Research modems are designed by using a digital-signal-processor (DSP is expensive) and field-programmable-gate-array (FPGA is high power consuming device). In addition to, the use of a microcontroller is also a common practice (which is less expensive) but provides limited computational power. Hence, there is a need for a cost-effective and energy-efficient UAM to be used in budget limited applications. In this thesis different objectives are proposed. First, to identify the limitations of state-of-the-art commercial and research UAMs through a comprehensive survey. The second contribution has been the design of a low-cost acoustic modem for short-range underwater communications by using a single board computer (Raspberry-Pi), and a microcontroller (Atmega328P). The modulator, demodulator and amplifiers are designed with discrete components to reduce the overall cost. The third contribution is to design a web based underwater acoustic communication testbed along with a simulation platform (with underwater channel and sound propagation models), for testing modems. The fourth contribution is to integrate in a single module two important modules present in UAMs: the PSK modulator and the power amplifier

Nanosatellite Store-and-Forward Communication Systems for Remote Data Collection Applications

Due to compact design, cost-effectiveness and shorter development time, a nanosatellite constellation is seen as a viable space-based data-relay asset to collect data from remote places that are rather impractical to be linked by terrestrial means. While nanosatellites have these advantages, they have more inherent technical limitations because of limited space for subsystems and payloads. Nanosatellite S&F communication systems are notably challenging in this respect due to requirements on antennas, transceivers, and signal processing. Although nanosatellites can be scaled up for better resources and capabilities, smaller platforms (i.e., ≤6U CubeSat) tend to be used for cost-effectiveness and lower risk. This thesis dealt with the problem of designing a nanosatellite S&F communication system for delay-tolerant remote data collection applications considering: (a) technical constraints in hardware, processing capabilities, energy budget and space in both the nanosatellite and ground sensor terminal (GST) sides; (b) physical communication layer characteristics and constraints such as limited available bandwidth, LEO channel Doppler, attenuation and fading/shadowing effects, low transmit power and data rate, and multi-user interference among asynchronously transmitting terminals. We designed, developed, and operated an amateur radio payload with S&F communication and APRS-DP capabilities, and performed a post-launch communication failure investigation. We also investigated suitability of E-SSA protocol for IoT/M2M terminals to nanosatellite communication by analyzing performance and energy efficiency metrics. The thesis comprises nine chapters. Chapter 1 describes the research background, problem, objectives, state of research, potential contributions of this thesis, and a gist of methodology detailed in later chapters. Chapter 2 and 3 provide an extensive literature review. Chapter 2 reviews the previous research works on using nanosatellites for S&F communication for remote data collection, and the previous nanosatellite S&F missions. Such research works and nanosatellite missions were undertaken primarily in the context of non-commercial/civil applications. Then, Chapter 2 surveys the recent commercial nanosatellite IoT/M2M players and examines their proposed systems in terms of satellite platform, constellation design, communication technology, targeted applications, requirements, and performance. Chapter 3 presents a literature review on communication system architecture, physical layer and random-access schemes, protocols, and technologies relevant to satellite IoT/M2M systems. In the context of IoT/M2M applications, the constraints in energy budget, transmit power and available bandwidth limit the system’s capacity in terms of amount of data that can be received and number of GSTs that can be supported. In both nanosatellite and GST sides, there are stringent limitations in hardware complexity, processing capabilities and energy budget. Addressing these challenges requires a simple, spectrally and energy efficient asynchronous random-access communication protocol. This research investigated using the enhanced spread spectrum Aloha (E-SSA) protocol for satellite IoT/M2M uplink (terminal to satellite) communication and analyzed its performance and suitability for the said application. Chapter 4 discusses the BIRDS-2 CubeSat S&F remote data collection system, payload design, development, tests, and integration with the BIRDS-2 CubeSats. Chapter 5 discusses the investigation on communication design issues of BIRDS-2 CubeSat S&F payload, tackling both the methodology and findings of investigation. It is noted that there are only a few satellites that have carried an APRS-DP payload but even some of these failed due to communication, power, or software issues. In BIRDS-2 Project, considering tight constraints in a 1U CubeSat equipped with other subsystems and payloads, we developed a S&F/APRS-DP payload and integrated it with each of the three 1U CubeSats of participating countries. After launching the CubeSats from the ISS, several amateur operators confirmed reception downlink beacon messages, but full two-way communication failed due to uplink communication failure. Thus, this research not only studied the design and development of a S&F/APRS-DP payload suitable for a CubeSat platform, but also systematically investigated the causes of communication failure by on-orbit observation results and ground-based tests. We found that uplink failure was caused by two design problems that were overlooked during development, namely, the poor antenna performance and increased payload receiver noise floor due to satellite-radiated EMI coupled to the antenna. Chapter 6 first describes the enhanced spread spectrum Aloha (E-SSA) based nanosatellite IoT/M2M communication model implemented in Matlab and derives the mathematical definitions of packet loss rate (PLR), throughput (THR) and energy efficiency (EE) metrics. Then, it tackles the formulated baseband signal processing algorithm for E-SSA, including packet detection, channel estimation, demodulation and decoding. Chapter 7 presents the simulation results and discussion for Chapter 6. Chapter 8 tackles the S&F nanosatellite constellation design for global coverage and presents the results and findings. Chapter 9 describes the laboratory setups for validating the E-SSA protocol and then presents the findings. Finally, Chapter 9 also gives the summary, conclusions, and recommendations. Simulation results showed that for E-SSA protocol with the formulated algorithm, THR, PLR and EE metrics are more sensitive to MAC load G, received power variation σLN and Eb/N0, due to imperfect detection and channel estimation. With loose power control (σLN=3dB), at Eb/N0=14 dB, the system can be operated up to a maximum load of 1.3 bps/Hz, achieving a maximum THR of 1.25 bps/Hz with PLR<0.03. Without power control (σLN=6dB,9dB), at Eb/N0=14 dB, maximum load is also 1.3 bps/Hz, but achievable THR is lower than ~1 bps/Hz and PLR values can be as high as ~0.23. Worse PLR results are attributed to misdetection of lower power packets and demodulation/decoding errors. Both are caused by the combined effects of MUI, channel estimation errors, imperfect interference cancellation residue power, and noise. The PLR and THR can be improved by operating with higher Eb/N0 at the expense of lower energy efficiency. Then, laboratory validation experiments using a SDR-based platform confirmed that with G=0.1, Eb/N0=14dB, σLN=6dB, the formulated algorithm for E-SSA protocol can still work even with inaccurate oscillator (±2 ppm) at GSTs, obtaining experimental PLR result of 0.0650 compared to simulation result of 0.0352. However, this requires lowering the detection thresholds and takes significantly longer processing time. For the S&F nanosatellite constellation design, it was found that to achieve the target percent coverage time (PCT) of more than 95% across all latitudes, a 9x10 Hybrid constellation or a 10x10 Walker Delta constellation would be required.九州工業大学博士学位論文 学位記番号：工博甲第506号 学位授与年月日：令和2年9月25日1: Introduction|2: Nanosatellite S&F Research, Missions and Applications|3: Satellite S&F Communication Systems and Protocols|4: BIRDS-2 CubeSat S&F Data Collection System, Payload Design and Development|5: Investigation on Communication Design Issues of BIRDS-2 CubeSat APRS-DP/S&F Payload, Results and Discussion|6: E-SSA-based Nanosatellite IoT/M2M Communication System Model and Signal Processing Algorithm|7: Simulation Results and Discussion for E-SSA-based Nanosatellite IoT/M2M Communication System|8: Nanosatellite Constellation for Global Coverage|9: Experimental Laboratory Validation for E-SSA Protocol, Research Summary, Conclusions and Recommendations九州工業大学令和2年

Ambient backscatterers for low cost and low power wireless applications

Sensors that are used in Internet-of-Things (IoT) area are hampered by extremely high costs and excessive battery power consumption – but wireless, reflective, sensor-tags could help address these issues. In agricultural applications: in order to monitor a field of 500 plants, the operating cost will typically rack up hundreds of pounds per field and will gobble tens of milliwatts per sensor. In this thesis we have tried to address some of these shortfalls by opting for each plant to have an antenna, one transistor that acts as a switch, and one microcontroller. Each sensor uses wireless communication based on a reflections technology known as backscatter. The antenna acts as a mirror and when it is illuminated with a signal, it reflects back the wave. The signal comes from an FM radio station and it is freely available in the air. The plant-sensor can modulate the information by a very smart switching of this antenna. We are trying, under laboratory conditions, to combine this low power, low-cost technology with tape-based, flexible nanomaterial printed sensors. As nanotechnology enables flexible inkjet printed electronics to revolutionise IoT applications, we developed a new technology and we hope that our nanomaterial based printed circuit sensors will help push state-of-the-art additive manufacturing in agricultural technology

常時オフセンサネットワーク向け低電力同期型コード変調OOK方式トランシーバーの研究

電気通信大学201

Low Power Circuit Design in Sustainable Self Powered Systems for IoT Applications

The Internet-of-Things (IoT) network is being vigorously pushed forward from many fronts in diverse research communities. Many problems are still there to be solved, and challenges are found among its many levels of abstraction. In this thesis we give an overview of recent developments in circuit design for ultra-low power transceivers and energy harvesting management units for the IoT. The first part of the dissertation conducts a study of energy harvesting interfaces and optimizing power extraction, followed by power management for energy storage and supply regulation. we give an overview of the recent developments in circuit design for ultra-low power management units, focusing mainly in the architectures and techniques required for energy harvesting from multiple heterogeneous sources. Three projects are presented in this area to reach a solution that provides reliable continuous operation for IoT sensor nodes in the presence of one or more natural energy sources to harvest from. The second part focuses on wireless transmission, To reduce the power consumption and boost the Tx energy efficiency, a novel delay cell exploiting current reuse is used in a ring-oscillator employed as the local oscillator generator scheme. In combination with an edge-combiner power amplifier, the Tx showed a measured energy efficiency of 0.2 nJ=bit and a normalized energy efficiency of 3.1 nJ=bit:mW when operating at output power levels up to -10 dBm and data rates of 3 Mbps

Part 1: acceptance test and administration of a farm of servers. Part 2: improving TCP performance in underwater wireless sensor networks

Dissertação de mestrado, Engenharia Informática, Faculdade de Ciências e Tecnologia, Universidade do Algarve, 2017Abstract 1 During the last decades, companies and organizations have focused on how to provide to the end-users or clients with web services or applications to make them more closer and involved to the activity. Therefore, many enterprises through their direction of the IT service, propose varieties of applications that allow to the stakeholders to perform what they need. The aim of this report is to present what the application integration job is and to report the missions that I have been able to carry out such as application integration, application qualification, and acceptance tests. This represents in total: - 19 qualified applications, - 33 administrated serversResumo 1 Ao longo das últimas décadas, as empresas e as organizações concentraram-se na forma de fornecer aos usuários finais ou clientes, serviços Web ou aplicativos para torná-los mais próximos e envolvidos na actividade. Portanto, muitas empresas através da sua direcção do serviço de Tecnólogia da Informação TI, propõem variedades de aplicativos que permitem às partes interessadas realizar o que necessitam. O objectivo deste relatório é apresentar o que é o trabalho de integração de aplicativos e as missões que fui capaz de executar, como a integração de aplicativos, a qualificação de aplicativos e testes de aceitação. Isto representa no total: - 19 aplicações qualificadas, - 33 servidores administradosAbstract 2 Underwater wireless sensor networks (UWSNs) are becoming popular due to their important role in different applications, such as offshore search and underwater monitoring. However, the data transmission in this underwater environment is impacted by various aspects such as bandwidth usage limitation, surrounding noise and large acoustic propagation delays. Therefore, communication itself is an outstanding challenge. The well-known traditional transmission control protocol (TCP), one of the most used transport protocol on the internet, is not suitable to enable this technology. Even though TCP variants for the wireless network are not foolproof in an underwater environment, their use could probably be more difficult in such a multi-hop communication system. We have chosen Newreno for our study. This variant is a modern implementation that includes the four congestion control algorithms. These algorithms have proved to be effective when it comes to terrestrial networks which could be a basis for our study. In addition, Newreno is known for its algorithm of recovery of several segments lost within the same sending window. In this dissertation, we have conducted a general study of UWSN technology and examined methods to improve TCP performance in a multi-hop UWSN. And then, we propose Underwater-Newreno (U-Newreno) our enhanced version of Newreno to improve TCP performance in UWSN. U-Newreno consists of two major modifications: controlling the maximum size of the congestion window and the adaptation of the round trip time (RTT) timeout. The results of simulations carried out with the Aquasim simulator show improvements of performances in terms of gain of: packets delivery Retransmission ratio of packets delivery.Resumo 2 As redes de sensores sem fio subaquáticos (Underwater Wireless Sensor Networks- UWSN) estão-se a tornar cada vez mais populares devido à sua importância em diferentes aplicações, como a pesquisa offshore e monitoramento subaquático. No entanto, a transmissão de dados neste ambiente subaquático sofre devido a vários factores, como a limitação do uso da largura de banda, o ruído envolvente e grandes atrasos de propagação acústica. Portanto, a comunicação é um desafio problemático. O familiar transmission control protocol (TCP) tradicional, um dos protocolos de transporte mais utilizados na internet, não é adequado para habilitar esta tecnologia. Mesmo que as variantes TCP para a rede sem fio não sejam infalíveis num ambiente subaquático, o seu uso provavelmente pode ser mais difícil num sistema de comunicação de múltiplos saltos. Nós escolhemos o Newreno para o nosso estudo. Esta variante é uma implementação moderna que inclui os quatro algoritmos de controle de congestionamento. Estes algoritmos demonstraram a sua eficácia em redes terrestres que poderiam ser uma base para o nosso estudo. Além disso, Newreno é conhecido pelo seu algoritmo de recuperação de vários segmentos perdidos dentro da mesma janela de envio. Nesta dissertação, realizamos um estudo geral da tecnologia UWSN e examinamos métodos para melhorar o desempenho do TCP num UWSN de vários saltos. E então, propomos a U-Newreno (Underwater-Newreno), a nossa versão melhorada do Newreno para melhorar o desempenho do TCP no UWSN. O U-Newreno consiste em duas modificações principais: controlar o tamanho máximo da janela de congestionamento e a adaptação do tempo limite “Round Trip Time”(RTT). Os resultados das simulações realizadas com o simulador Aquasim mostram melhorias nos desempenhos em termos de ganho de: • entrega de pacotes • Taxa de retransmissão da entrega de pacotes