EC-GSM-IoT Network Synchronization with Support for Large Frequency Offsets

EDGE-based EC-GSM-IoT is a promising candidate for the billion-device cellular IoT (cIoT), providing similar coverage and battery life as NB-IoT. The goal of 20 dB coverage extension compared to EDGE poses significant challenges for the initial network synchronization, which has to be performed well below the thermal noise floor, down to an SNR of -8.5 dB. We present a low-complexity synchronization algorithm supporting up to 50 kHz initial frequency offset, thus enabling the use of a low-cost +/-25 ppm oscillator. The proposed algorithm does not only fulfill the 3GPP requirements, but surpasses them by 3 dB, enabling communication with an SNR of -11.5 dB or a maximum coupling loss of up to 170.5 dB.Comment: Wireless Communications and Networking Conference (WCNC), 201

Improving the Performance of OTDOA based Positioning in NB-IoT Systems

In this paper, we consider positioning with observed-time-difference-of-arrival (OTDOA) for a device deployed in long-term-evolution (LTE) based narrow-band Internet-of-things (NB-IoT) systems. We propose an iterative expectation-maximization based successive interference cancellation (EM-SIC) algorithm to jointly consider estimations of residual frequency-offset (FO), fading-channel taps and time-of-arrival (ToA) of the first arrival-path for each of the detected cells. In order to design a low complexity ToA detector and also due to the limits of low-cost analog circuits, we assume an NB-IoT device working at a low-sampling rate such as 1.92 MHz or lower. The proposed EM-SIC algorithm comprises two stages to detect ToA, based on which OTDOA can be calculated. In a first stage, after running the EM-SIC block a predefined number of iterations, a coarse ToA is estimated for each of the detected cells. Then in a second stage, to improve the ToA resolution, a low-pass filter is utilized to interpolate the correlations of time-domain PRS signal evaluated at a low sampling-rate to a high sampling-rate such as 30.72 MHz. To keep low-complexity, only the correlations inside a small search window centered at the coarse ToA estimates are upsampled. Then, the refined ToAs are estimated based on upsampled correlations. If at least three cells are detected, with OTDOA and the locations of detected cell sites, the position of the NB-IoT device can be estimated. We show through numerical simulations that, the proposed EM-SIC based ToA detector is robust against impairments introduced by inter-cell interference, fading-channel and residual FO. Thus significant signal-to-noise (SNR) gains are obtained over traditional ToA detectors that do not consider these impairments when positioning a device.Comment: Accepted in GlobeCom 2017, 7 pages, 11 figure

Low-power Physical-layer Design for LTE Based Very NarrowBand IoT (VNB - IoT) Communication

abstract: With the new age Internet of Things (IoT) revolution, there is a need to connect a wide range of devices with varying throughput and performance requirements. In this thesis, a wireless system is proposed which is targeted towards very low power, delay insensitive IoT applications with low throughput requirements. The low cost receivers for such devices will have very low complexity, consume very less power and hence will run for several years. Long Term Evolution (LTE) is a standard developed and administered by 3rd Generation Partnership Project (3GPP) for high speed wireless communications for mobile devices. As a part of Release 13, another standard called narrowband IoT (NB-IoT) was introduced by 3GPP to serve the needs of IoT applications with low throughput requirements. Working along similar lines, this thesis proposes yet another LTE based solution called very narrowband IoT (VNB-IoT), which further reduces the complexity and power consumption of the user equipment (UE) while maintaining the base station (BS) architecture as defined in NB-IoT. In the downlink operation, the transmitter of the proposed system uses the NB-IoT resource block with each subcarrier modulated with data symbols intended for a different user. On the receiver side, each UE locks to a particular subcarrier frequency instead of the entire resource block and operates as a single carrier receiver. On the uplink, the system uses a single-tone transmission as specified in the NB-IoT standard. Performance of the proposed system is analyzed in an additive white Gaussian noise (AWGN) channel followed by an analysis of the inter carrier interference (ICI). Relationship between the overall filter bandwidth and ICI is established towards the end.Dissertation/ThesisMasters Thesis Electrical Engineering 201

Architectures and Key Technical Challenges for 5G Systems Incorporating Satellites

Satellite Communication systems are a promising solution to extend and complement terrestrial networks in unserved or under-served areas. This aspect is reflected by recent commercial and standardisation endeavours. In particular, 3GPP recently initiated a Study Item for New Radio-based, i.e., 5G, Non-Terrestrial Networks aimed at deploying satellite systems either as a stand-alone solution or as an integration to terrestrial networks in mobile broadband and machine-type communication scenarios. However, typical satellite channel impairments, as large path losses, delays, and Doppler shifts, pose severe challenges to the realisation of a satellite-based NR network. In this paper, based on the architecture options currently being discussed in the standardisation fora, we discuss and assess the impact of the satellite channel characteristics on the physical and Medium Access Control layers, both in terms of transmitted waveforms and procedures for enhanced Mobile BroadBand (eMBB) and NarrowBand-Internet of Things (NB-IoT) applications. The proposed analysis shows that the main technical challenges are related to the PHY/MAC procedures, in particular Random Access (RA), Timing Advance (TA), and Hybrid Automatic Repeat reQuest (HARQ) and, depending on the considered service and architecture, different solutions are proposed.Comment: Submitted to Transactions on Vehicular Technologies, April 201

Analytical Modeling and Experimental Validation of NB-IoT Device Energy Consumption

The recent standardization of 3GPP Narrowband Internet of Things (NB-IoT) paves the way to support low-power wide-area (LPWA) use cases in cellular networks. NB-IoT design goals are extended coverage, low power and low cost devices, and massive connections. As a new radio access technology, it is necessary to analyze the possibilities NB-IoT provides to support different traffic and coverage needs. In this paper, we propose and validate an NB-IoT energy consumption model. The analytical model is based on a Markov chain. For the validation, an experimental setup is used to measure the energy consumption of two commercial NB-IoT user equipments (UEs) connected to a base station emulator. The evaluation is done considering three test cases. The comparison of the model and measurements is done in terms of the estimated battery lifetime and the latency needed to finish the control plane procedure. The conducted evaluation shows the analytical model performs well, obtaining a maximum relative error of the battery lifetime estimation between the model and the measurements of 21% for an assumed interarrival time (IAT) of 6 min.This work was supported in part by the Spanish Ministry of Economy and Competitiveness and the European Regional Development Fund under Project TEC2016-76795-C6-4-R and in part by the H2020 European Project TRIANGLE under Grant 688712

Kapeankaistan LTE koneiden välisessä satelliittitietoliikenteessä

Recent trends to wireless Machine-to-Machine (M2M) communication and Internet of Things (IoT) has created a new demand for more efficient low-throughput wireless data connections. Beside the traditional wireless standards, focused on high bandwidth data transfer, has emerged a new generation of Low Power Wide Area Networks (LPWAN) which targets for less power demanding low-throughput devices requiring inexpensive data connections. Recently released NB-IoT (Narrowband IoT) specification extends the existing 4G/LTE standard allowing more easily accessible LPWAN cellular connectivity for IoT devices. Narrower bandwidth and lower data rates combined to a simplified air interface make it less resource demanding still benefiting from the widely spread LTE technologies and infrastructure. %% Applications & Why space Applications, such as wide scale sensor or asset tracking networks, can benefit from a global scale network coverage and easily available low-cost user equipment which could be made possible by new narrowband IoT satellite networks. In this thesis, the NB-IoT specification and its applicability for satellite communication is discussed. Primarily, LTE and NB-IoT standards are designed only for terrestrial and their utilization in Earth-to-space communication raises new challenges, such as timing and frequency synchronization requirements when utilizing Orthogonal Frequency Signal Multiplexing (OFDM) techniques. Many of these challenges can be overcome by specification adaptations and other existing techniques making minimal changes to the standard and allowing extension of the terrestrial cellular networks to global satellite access.Viimeaikaiset kehitystrendit koneiden välisessä kommunikaatiossa (Machine to Machine Communication, M2M) ja esineiden Internet (Internet of Things, IoT) -sovelluksissa ovat luoneet perinteisteisten nopean tiedonsiirron langattomien standardien ohelle uuden sukupolven LPWAN (Low Power Wide Area Networks) -tekniikoita, jotka ovat tarkoitettu pienitehoisille tiedonsiirtoa tarvitseville sovelluksille. Viimeaikoina yleistynyt NB-IoT standardi laajentaa 4G/LTE standardia mahdollistaen entistä matalamman virrankulutuksen matkapuhelinyhteydet IoT laitteissa. Kapeampi lähetyskaista ja hitaampi tiedonsiirtonopeus yhdistettynä yksinkertaisempaan ilmarajapintaan mahdollistaa pienemmän resurssivaatimukset saman aikaan hyötyen laajalti levinneistä LTE teknologioista ja olemassa olevasta infrastruktuurista. Useissa sovelluskohteissa, kuten suurissa sensoriverkoissa, voitaisiin hyötyä merkittävästi globaalista kattavuudesta yhdistettynä edullisiin helposti saataviin päätelaitteisiin. Tässä työssä käsitellään NB-IoT standardia ja sen soveltuvuutta satellittitietoliikenteeseen. LTE ja NB-IoT ovat kehitty maanpääliseen tietoliikenteeseen ja niiden hyödyntäminen avaruuden ja maan välisessä kommunikaatiossa aiheuttaa uusia haasteita esimerkiksi aika- ja taajuussynkronisaatiossa ja OFDM (Orthogonal Frequency Signal Multiplexing) -tekniikan hyödyntämisessä. Nämä haasteet voidaan ratkaista soveltamalla spesifikaatiota sekä muilla jo olemassa olevilla tekniikoilla tehden mahdollisimman vähän muutoksia alkuperäiseen standardiin, ja täten sallien maanpäälisten IoT verkkojen laajenemisen avaruuteen