10 research outputs found

    Design Of Robust Feedback Controllers For A Laser Beam Stabilizer

    Get PDF
    This work addresses this challenge by employing two different control strategies, namely, Proportional Integral Derivative (PID) and State Feedback with an observer for control

    Damping controller design for FACTS devices in power systems using novel control techniques

    Get PDF
    Power systems are under increasing stress as deregulation introduces several new economic objectives for operation. Since power systems are being operated close to their limits, weak connections, unexpected events, hidden failures in protection system, human errors, and a host of other factors may cause a system to lose stability and even lead to catastrophic failure. Therefore, the need for improved system damping in a wider operating range is gaining more attention. Among the available damping control methods, each approach has advantages and disadvantages in different systems. The effectiveness of damping control depends on the devices chosen, the system modal feature, and the applied controller design method;In the literature, many approaches have been proposed to undertake this task. However, some of these approaches only take a fixed operating point into consideration without describing the changing uncertainty in varying system conditions; computational effort. Furthermore, no systematic comparison of controller design methods has been conducted with regard to different system profiles. Attention has been drawn to the enhanced susceptibility to inter-area oscillations between groups of machines under large others require a great deal of variation of system operating conditions. The linear parameter varying (LPV) approach, which has been widely studied in the literature, provides a potential method for capturing the varying system condition precisely without formulation of system uncertainty. However, in some cases no solution can be achieved if the system variation is too large using the traditional LPV approach. Also, sometimes the system structure imposes limitations in the achievable damping performance. In general, there is a critical need for a cost-effective control strategy applicable to different systems from an economic point of view;In this dissertation, a comprehensive comparison among controller design methods has been conducted to study the damping effectiveness of different FACTS devices. Based on these, a robust regional pole-placement method is applied in a TCSC damping controller design in a 4-machine system; an interpolated LPV approach is proposed and applied to designing a SVC damping controller in the IEEE 50-machine system; finally with the advantage of an additional feedback signal, limitations in achieving satisfactory damping performance can be relieved using a two-input single-output (TISO) damping controller for a TCSC in the IEEE 50-machine system

    A Foot Placement Strategy for Robust Bipedal Gait Control

    Get PDF
    This thesis introduces a new measure of balance for bipedal robotics called the foot placement estimator (FPE). To develop this measure, stability first is defined for a simple biped. A proof of the stability of a simple biped in a controls sense is shown to exist using classical methods for nonlinear systems. With the addition of a contact model, an analytical solution is provided to define the bounds of the region of stability. This provides the basis for the FPE which estimates where the biped must step in order to be stable. By using the FPE in combination with a state machine, complete gait cycles are created without any precalculated trajectories. This includes gait initiation and termination. The bipedal model is then advanced to include more realistic mechanical and environmental models and the FPE approach is verified in a dynamic simulation. From these results, a 5-link, point-foot robot is designed and constructed to provide the final validation that the FPE can be used to provide closed-loop gait control. In addition, this approach is shown to demonstrate significant robustness to external disturbances. Finally, the FPE is shown in experimental results to be an unprecedented estimate of where humans place their feet for walking and jumping, and for stepping in response to an external disturbance

    An apparatus for high throughput muscle cell experimentation

    Get PDF
    Thesis (Ph. D.)--Massachusetts Institute of Technology, Biological Engineering Division, 2006.MIT Science Library copy: printed in pages versus leaves.Also issued in pages.Includes bibliographical references (leaves 183-197).The cardiac ventricular muscle cell (myocyte) is a key experimental system for exploring the mechanical properties of the diseased and healthy heart. The myocyte experimental model provides a higher level of physiological relevance than molecular or myofibril studies while avoiding problems inherent to multicellular preparations including heterogeneity of cell types and diffusion limited extracellular spaces. Millions of primary myocytes that remain viable for four to six hours can be readily isolated from animal models. However, the mechanical properties of only a few physically loaded myocytes can be explored in this time period using current, bulky and expensive instrumentation. In this thesis, a prototype instrument is described that is modular and inexpensive and could form the basis of an array of devices for probing the mechanical properties of single mammnalian myocytes in parallel. This would greatly increase the throughput of scientific experimentation and could be applied as a high content screening instrument in the pharmaceutical industry providing information at the level of a critical cellular phenotype, myocyte mechanical properties, for drug development and toxicology studies.(cont.) The design, development and experimental verification of the modular instrument are presented here. The mathematical, mechanical and electrical characteristics of the novel force sensor and actuator system, Ho control implementation and data processing methodology are discussed. Finally, the functionality of the instrument is demonstrated by implementing novel methodologies for loading and attaching healthy, single mammalian ventricular myocytes to the force sensor and actuator and measuring their isometric twitch force and passive dynamic stiffness at varied sarcomere lengths.by Michael G. Garcia-Webb.Ph.D

    Summary of Research 1994

    Get PDF
    The views expressed in this report are those of the authors and do not reflect the official policy or position of the Department of Defense or the U.S. Government.This report contains 359 summaries of research projects which were carried out under funding of the Naval Postgraduate School Research Program. A list of recent publications is also included which consists of conference presentations and publications, books, contributions to books, published journal papers, and technical reports. The research was conducted in the areas of Aeronautics and Astronautics, Computer Science, Electrical and Computer Engineering, Mathematics, Mechanical Engineering, Meteorology, National Security Affairs, Oceanography, Operations Research, Physics, and Systems Management. This also includes research by the Command, Control and Communications (C3) Academic Group, Electronic Warfare Academic Group, Space Systems Academic Group, and the Undersea Warfare Academic Group

    The optimal control of power electronic embedded networks in More Electric Aircraft

    Get PDF
    With the advancement of power electronic technologies over recent decades, there has been an overall increase in the utilisation of distributed generation and power electronic embedded networks in a large sphere of applications. Probably one of the most prominent areas of utilisation of new power electronics embedded systems is the use in power networks onboard military and civilian aircraft. With environmental concerns and increased competition in the civil aviation sector, more aircraft manufactures are replacing and interfacing electrical alternatives over heavier, less efficient and costly pneumatic, hydraulic and mechanical systems. In these modern power systems, the increased proliferation of power electronic converters and distributed generation raises important issues in regards to the performance, stability and robustness between interfaced switching units. These phenomena, such as power electronic sub-system interactions, become even more prominent in micro-grid applications or other low voltage distribution systems where interfaced converters are in close proximity to one another. In More Electric Aircraft (MEA), these interfaced power electronic converters are connected to the same non-stiff low power AC grid, which further increases the interactive effects between converter sub-systems. If these effects are not properly taken into account, then external disturbances to the system at given operating conditions can result in degradation of the system performance, failure in meeting the operating requirements of the grid, or in the worst case, instability of the whole grid. With much research in the area of decreasing the size and weight of systems, there is much literature proposing optimisation methods which decrease the size of filters between interfacing converters. Whilst effectively decreasing the size of these systems, interactions between interfaced converters gets worse, and is often improperly accounted for. The work presented in this thesis proposes a novel approach to the decentralisation and optimisation of converter controls on a power electronics embedded power network. In order to account for the interactive dynamics between sub-systems in the environment of reduced passive filter networks, all the system dynamics including the interactive terms are modelled globally. An optimal controller design approach based on the H2 optimisation is proposed to synthesise and generate automatically the controller gains for each power electronic sub-system. H2 optimisation is a powerful tool, which not only allows the submission, optimisation and development of closed loop controls for large dynamic systems, but offers the ability to the user to construct the controller for given structures. This enables the development of decentralised controllers for every sub-system with intrinsic knowledge of the closed loop dynamics of every other interconnect sub-system. It is shown through simulation and by experimental validation that this novel approach to grid control optimisation not only can improve overall dynamic performance of all sub-systems over 15traditional methods of design, but can also intrinsically reduce or better yet mitigate against the interactive effects between all converters. In addition, this method of controller design will be shown to not only be scalable to expanding sizes of grids, but the Phase-locked loops (PLLs) integrated to grid connected devices can also be considered in the optimisation procedure. PLLs are widely known to further cause interactive behaviours between grid interfaced devices. Including this into the optimisation also has been validated experimentally to prevent interactions on the grid, and improve performance over traditional design methods. Adaptations to the controller are performed to ensure operation in variable frequency environments (as is common in MEA), as well as methods of single converter optimisation when interfacing to an unknown grid. Additionally some initial research towards an adaption of the H2 controller to incorporate robustness as well as performance into the optimisation procedure is presented with mathematical concepts shown through simulation

    The optimal control of power electronic embedded networks in More Electric Aircraft

    Get PDF
    With the advancement of power electronic technologies over recent decades, there has been an overall increase in the utilisation of distributed generation and power electronic embedded networks in a large sphere of applications. Probably one of the most prominent areas of utilisation of new power electronics embedded systems is the use in power networks onboard military and civilian aircraft. With environmental concerns and increased competition in the civil aviation sector, more aircraft manufactures are replacing and interfacing electrical alternatives over heavier, less efficient and costly pneumatic, hydraulic and mechanical systems. In these modern power systems, the increased proliferation of power electronic converters and distributed generation raises important issues in regards to the performance, stability and robustness between interfaced switching units. These phenomena, such as power electronic sub-system interactions, become even more prominent in micro-grid applications or other low voltage distribution systems where interfaced converters are in close proximity to one another. In More Electric Aircraft (MEA), these interfaced power electronic converters are connected to the same non-stiff low power AC grid, which further increases the interactive effects between converter sub-systems. If these effects are not properly taken into account, then external disturbances to the system at given operating conditions can result in degradation of the system performance, failure in meeting the operating requirements of the grid, or in the worst case, instability of the whole grid. With much research in the area of decreasing the size and weight of systems, there is much literature proposing optimisation methods which decrease the size of filters between interfacing converters. Whilst effectively decreasing the size of these systems, interactions between interfaced converters gets worse, and is often improperly accounted for. The work presented in this thesis proposes a novel approach to the decentralisation and optimisation of converter controls on a power electronics embedded power network. In order to account for the interactive dynamics between sub-systems in the environment of reduced passive filter networks, all the system dynamics including the interactive terms are modelled globally. An optimal controller design approach based on the H2 optimisation is proposed to synthesise and generate automatically the controller gains for each power electronic sub-system. H2 optimisation is a powerful tool, which not only allows the submission, optimisation and development of closed loop controls for large dynamic systems, but offers the ability to the user to construct the controller for given structures. This enables the development of decentralised controllers for every sub-system with intrinsic knowledge of the closed loop dynamics of every other interconnect sub-system. It is shown through simulation and by experimental validation that this novel approach to grid control optimisation not only can improve overall dynamic performance of all sub-systems over 15traditional methods of design, but can also intrinsically reduce or better yet mitigate against the interactive effects between all converters. In addition, this method of controller design will be shown to not only be scalable to expanding sizes of grids, but the Phase-locked loops (PLLs) integrated to grid connected devices can also be considered in the optimisation procedure. PLLs are widely known to further cause interactive behaviours between grid interfaced devices. Including this into the optimisation also has been validated experimentally to prevent interactions on the grid, and improve performance over traditional design methods. Adaptations to the controller are performed to ensure operation in variable frequency environments (as is common in MEA), as well as methods of single converter optimisation when interfacing to an unknown grid. Additionally some initial research towards an adaption of the H2 controller to incorporate robustness as well as performance into the optimisation procedure is presented with mathematical concepts shown through simulation

    Six Decades of Flight Research: An Annotated Bibliography of Technical Publications of NASA Dryden Flight Research Center, 1946-2006

    Get PDF
    Titles, authors, report numbers, and abstracts are given for nearly 2900 unclassified and unrestricted technical reports and papers published from September 1946 to December 2006 by the NASA Dryden Flight Research Center and its predecessor organizations. These technical reports and papers describe and give the results of 60 years of flight research performed by the NACA and NASA, from the X-1 and other early X-airplanes, to the X-15, Space Shuttle, X-29 Forward Swept Wing, X-31, and X-43 aircraft. Some of the other research airplanes tested were the D-558, phase 1 and 2; M-2, HL-10 and X-24 lifting bodies; Digital Fly-By-Wire and Supercritical Wing F-8; XB-70; YF-12; AFTI F-111 TACT and MAW; F-15 HiDEC; F-18 High Alpha Research Vehicle, F-18 Systems Research Aircraft and the NASA Landing Systems Research aircraft. The citations of reports and papers are listed in chronological order, with author and aircraft indices. In addition, in the appendices, citations of 270 contractor reports, more than 200 UCLA Flight System Research Center reports, nearly 200 Tech Briefs, 30 Dryden Historical Publications, and over 30 videotapes are included
    corecore