255 research outputs found

    Analog baseband circuits for sensor systems

    Get PDF
    This thesis is composed of six publications and an overview of the research topic, which also summarizes the work. The research presented in this thesis focuses on research into analog baseband circuits for sensor systems. The research is divided into three different topics: the integration of analog baseband circuits into a radio receiver for sensor applications; the integration of an ΔΣ modulator A/D converter into a GSM/WCDMA radio receiver for mobile phones, and the integration of algorithmic A/D converters for a capacitive micro-accelerometer interface. All the circuits are implemented using deep sub-micron CMOS technologies. The work summarizes the design of different blocks for sensor systems. The research into integrated analog baseband circuits for a radio receiver focuses on a circuit structures with a very low power dissipation and that can be implemented using only standard CMOS technologies. The research into integrated ΔΣ modulator A/D converter design for a GSM/WCDMA radio receiver for mobile phones focuses on the implications for analog circuit design emerging from using a very deep sub-micron CMOS process. Finally, in the research into algorithmic A/D converters for a capacitive microaccelerometer interface, new ways of achieving a good performance with low power dissipation, while also minimizing the silicon area of the integrated A/D converter are introduced

    Four-element phased-array beamformers and a self-interference canceling full-duplex transciver in 130-nm SiGe for 5G applications at 26 GHz

    Get PDF
    This thesis is on the design of radio-frequency (RF) integrated front-end circuits for next generation 5G communication systems. The demand for higher data rates and lower latency in 5G networks can only be met using several new technologies including, but not limited to, mm-waves, massive-MIMO, and full-duplex. Use of mm-waves provides more bandwidth that is necessary for high data rates at the cost of increased attenuation in air. Massive-MIMO arrays are required to compensate for this increased path loss by providing beam steering and array gain. Furthermore, full duplex operation is desirable for improved spectrum efficiency and reduced latency. The difficulty of full duplex operation is the self-interference (SI) between transmit (TX) and receive (RX) paths. Conventional methods to suppress this interference utilize either bulky circulators, isolators, couplers or two separate antennas. These methods are not suitable for fully-integrated full-duplex massive-MIMO arrays. This thesis presents circuit and system level solutions to the issues summarized above, in the form of SiGe integrated circuits for 5G applications at 26 GHz. First, a full-duplex RF front-end architecture is proposed that is scalable to massive-MIMO arrays. It is based on blind, RF self-interference cancellation that is applicable to single/shared antenna front-ends. A high resolution RF vector modulator is developed, which is the key building block that empowers the full-duplex frontend architecture by achieving better than state-of-the-art 10-b monotonic phase control. This vector modulator is combined with linear-in-dB variable gain amplifiers and attenuators to realize a precision self-interference cancellation circuitry. Further, adaptive control of this SI canceler is made possible by including an on-chip low-power IQ downconverter. It correlates copies of transmitted and received signals and provides baseband/dc outputs that can be used to adaptively control the SI canceler. The solution comes at the cost of minimal additional circuitry, yet significantly eases linearity requirements of critical receiver blocks at RF/IF such as mixers and ADCs. Second, to complement the proposed full-duplex front-end architecture and to provide a more complete solution, high-performance beamformer ICs with 5-/6- b phase and 3-/4-b amplitude control capabilities are designed. Single-channel, separate transmitter and receiver beamformers are implemented targeting massive- MIMO mode of operation, and their four-channel versions are developed for phasedarray communication systems. Better than state-of-the-art noise performance is obtained in the RX beamformer channel, with a full-channel noise figure of 3.3 d

    Linear Predistortion-less MIMO Transmitters

    Get PDF

    Calibration techniques in nyquist A/D converters

    Get PDF
    In modern systems signal processing is performed in the digital domain. Contrary to analog circuits, digital signal processing offers more robustness, programmability, error correction and storage possibility. The trend to shift the A/D converter towards the input of the system requires A/D converters with more dynamic range and higher sampling speeds. This puts extreme demands on the A/D converter and potentially increases the power consumption. Calibration Techniques in Nyquist A/D Converters analyses different A/D-converter architectures with an emphasis on the maximum achievable power efficiency. It is shown that in order to achieve high speed and high accuracy at high power efficiency, calibration is required. Calibration reduces the overall power consumption by using the available digital processing capability to relax the demands on critical power hungry analog components. Several calibration techniques are analyzed. The calibration techniques presented in this book are applicable to other analog-to-digital systems, such as those applied in integrated receivers. Further refinements will allow using analog components with less accuracy, which will then be compensated by digital signal processing. The presented methods allow implementing this without introducing a speed or power penalty

    Behavioural simulation of mixed analogue/digital circuits.

    Get PDF
    Continuing improvements in integrated circuit technology have made possible the implementation of complex electronic systems on a single chip. This often requires both analogue and digital signal processing. It is essential to simulate such IC's during the design process to detect errors at an early stage. Unfortunately, the simulators that are currently available are not well-suited to large mixed-signal circuits. This thesis describes the design and development of a new methodology for simulating analogue and digital components in a single, integrated environment. The methodology represents components as behavioural models that are more efficient than the circuit models used in conventional simulators. The signals that flow between models are all represented as piecewise-linear (PWL) waveforms. Since models representing digital and analogue components use the same format to represent their signals, they can be directly connected together. An object-oriented approach was used to create a class hierarchy to implement the component models. This supports rapid development of new models since all models are derived from a common base class and inherit the methods and attributes defined in their parentc lassesT. he signal objectsa re implementedw ith a similar class hierarchy. The development and validation of models representing various digital, analogue and mixed-signal components are described. Comparisons are made between the accuracy and performance of the proposed methodology and several commercial simulators. The development of a Windows-based demonstrations imulation tool called POISE is also described. This permitted models to be tested independently and multiple models to be connected together to form structural models of complex circuits

    An X-Band power amplifier design for on-chip RADAR applications

    Get PDF
    Tremendous growth of RAdio Detecting And Ranging (RADAR) and communication electronics require low manufacturing cost, excellent performance, minimum area and highly integrated solutions for transmitter/receiver (T/R) modules, which are one of the most important blocks of RADAR systems. New circuit topologies and process technologies are investigated to fulfill these requirements of next generation RADAR systems. With the recent improvements, Silicon-Germanium Bipolar CMOS technology became a good candidate for recently used III-V technologies, such as GaAs, InP, and GaN, to meet high speed and performance requirements of present RADAR applications. As new process technologies are used, new solutions and circuit architectures have to be provided while taking into account the advantages and disadvantageous of used technologies. In this thesis, a new T/R module system architecture is presented for single/onchip X-Band phased array RADAR applications. On-chip T/R module consists of five blocks; T/R switch, single-pole double-throw (SPDT) switch, low noise amplifier (LNA), power amplifier (PA), and phase shifter. As the main focus of this thesis, a two-stage power amplifier is realized, discussed and measured. Designed in IHP's 0.25 [micrometer] SiGe BiCMOS process technology, the power amplifier operates in Class-A mode to achieve high linearity and presents a measured small-signal gain of 25 dB at 10 GHz. While achieving an output power of 22 dBm, the power amplifier has drain efficiency of 30 % in saturation. The total die area is 1 [square millimeters], including RF and DC pads. To our knowledge, these results are comparable to and/or better than those reported in the literature

    Ageing and embedded instrument monitoring of analogue/mixed-signal IPS

    Get PDF

    34th Midwest Symposium on Circuits and Systems-Final Program

    Get PDF
    Organized by the Naval Postgraduate School Monterey California. Cosponsored by the IEEE Circuits and Systems Society. Symposium Organizing Committee: General Chairman-Sherif Michael, Technical Program-Roberto Cristi, Publications-Michael Soderstrand, Special Sessions- Charles W. Therrien, Publicity: Jeffrey Burl, Finance: Ralph Hippenstiel, and Local Arrangements: Barbara Cristi
    corecore