ATPG for Faults Analysis in VLSI Circuits Using Immune Genetic Algorithm

As design trends move toward nanometer technology, new Automatic Test Pattern Generation (ATPG)problems are merging. During design validation, the effect of crosstalk on reliability and performance cannot be ignored. So new ATPG Techniques has to be developed for testing crosstalk faults which affect the timing behaviour of circuits. In this paper, we present a Genetic Algorithm (GA) based test generation for crosstalk induced delay faults in VLSI circuits. The GA produces reduced test set which contains as few as possible test vector pairs, which detect as many as possible crosstalk delay faults. It uses a crosstalk delay fault simulator which computes the fitness of each test sequence. Tests are generated for ISCAS’85 and scan version of ISCAS’89 benchmark circuits. Experimental results demonstrate that GA gives higher fault coverage and compact test vectors for most of the benchmark circuits

On Co-Optimization Of Constrained Satisfiability Problems For Hardware Software Applications

Manufacturing technology has permitted an exponential growth in transistor count and density. However, making efficient use of the available transistors in the design has become exceedingly difficult. Standard design flow involves synthesis, verification, placement and routing followed by final tape out of the design. Due to the presence of various undesirable effects like capacitive crosstalk, supply noise, high temperatures, etc., verification/validation of the design has become a challenging problem. Therefore, having a good design convergence may not be possible within the target time, due to a need for a large number of design iterations. Capacitive crosstalk is one of the major causes of design convergence problems in deep sub-micron era. With scaling, the number of crosstalk violations has been increasing because of reduced inter-wire distances. Consequently only the most severe crosstalk faults are fixed pre-silicon while the rest are tested post-silicon. Testing for capacitive crosstalk involves generation of input patterns which can be applied post-silicon to the integrated circuit and comparison of the output response. These patterns are generated at the gate/ Register Transfer Level (RTL) of abstraction using Automatic Test Pattern Generation (ATPG) tools. In this dissertation, anInteger Linear Programming (ILP) based ATPG technique for maximizing crosstalk induced delay increase at the victim net, for multiple aggressor crosstalk faults, is presented. Moreover, various solutions for pattern generation considering both zero as well as unit delay models is also proposed. With voltage scaling, power supply switching noise has become one of the leading causes of signal integrity related failures in deep sub-micron designs. Hence, during power supply network design and analysis of power supply switching noise, computation of peak supply current is an essential step. Traditional peak current estimation approaches involve addition of peak current associated with all the CMOS gates which are switching in a combinational circuit. Consequently, this approach does not take the Boolean and temporal relationships of the circuit into account. This work presents an ILP based technique for generation of an input pattern pair which maximizes switching supply currents for a combinational circuit in the presence of integer gate delays. The input pattern pair generated using the above approach can be applied post-silicon for power droop testing. With high level of integration, Multi-Processor Systems on Chip (MPSoC) feature multiple processor cores and accelerators on the same die, so as to exploit the instruction level parallelism in the application. For hardware-software co-design, application programming model is based on a Task Graph, which represents task dependencies and execution/transfer times for various threads and processes within an application. Mapping an application to an MPSoC traditionally involves representing it in the form of a task graph and employing static scheduling in order to minimize the schedule length. Dynamic system behavior is not taken into consideration during static scheduling, while dynamic scheduling requires the knowledge of task graph at runtime. A run-time task graph extraction heuristic to facilitate dynamic scheduling is also presented here. A novel game theory based approach uses this extracted task graph to perform run-time scheduling in order to minimize total schedule length. With increase in transistor density, power density has gone up substantially. This has lead to generation of regions with very high temperature called Hotspots. Hotspots lead to reliability and performance issues and affect design convergence. In current generation Integrated Circuits (ICs) temperature is controlled by reducing power dissipation using Dynamic Thermal Management (DTM) techniques like frequency and/or voltage scaling. These techniques are reactive in nature and have detrimental effects on performance. Here, a look-ahead based task migration technique is proposed, in order to utilize the multitude of cores available in an MPSoC to eliminate thermal emergencies. Our technique is based on temperature prediction, leveraging upon a novel wavelet based thermal modeling approach. Hence, this work addresses several optimization problems that can be reduced to constrained max-satisfiability, involving integer as well as Boolean constraints in hardware and software domains. Moreover, it provides domain specific heuristic solutions for each of them

Modelling and Test Generation for Crosstalk Faults in DSM Chips

In the era of deep submicron technology (DSM), many System-on-Chip (SoC) applications require the components to be operating at high clock speeds. With the shrinking feature size and ever increasing clock frequencies, the DSM technology has led to a well-known problem of Signal Integrity (SI) more especially in the connecting layout design. The increasing aspect ratios of metal wires and also the ratio of coupling capacitance over substrate capacitance result in electrical coupling of interconnects which leads to crosstalk problems. In this thesis, first the work carried out to model the crosstalk behaviour between aggressor and victim by considering the distributed RLGC parameters of interconnect and the coupling capacitance and mutual conductance between the two nets is presented. The proposed model also considers the RC linear models of the CMOS drivers and receivers. The behaviour of crosstalk in case of under etching problem has been studied and modelled by distributing and approximating the defect behaviour throughout the nets. Next, the proposed model has also been extended to model the behaviour of crosstalk in case of one victim is influenced by several aggressors by considering all aggressors have similar effect (worst-case) on victim. In all the above cases simulation experiments were also carried out and compared with well-known circuit simulation tool PSPICE. It has been proved that the generated crosstalk model is faster and the results generated are within 10% of error margin compared to latter simulation tool. Because of the accuracy and speed of the proposed model, the model is very useful for both SoC designers and test engineers to analyse the crosstalk behaviour. Each manufactured device needs to be tested thoroughly to ensure the functionality before its delivery. The test pattern generation for crosstalk faults is also necessary to test the corresponding crosstalk faults. In this thesis, the well-known PODEM algorithm for stuck-at faults is extended to generate the test patterns for crosstalk faults between single aggressor and single victim. To apply modified PODEM for crosstalk faults, the transition behaviour has been divided into two logic parts as before transition and after transition. After finding individually required test patterns for before transition and after transition, the generated logic vectors are appended to create transition test patterns for crosstalk faults. The developed algorithm is also applied for a few ISCAS 85 benchmark circuits and the fault coverage is found excellent in most circuits. With the incorporation of proposed algorithm into the ATPG tools, the efficiency of testing will be improved by generating the test patterns for crosstalk faults besides for the conventional stuck-at faults. In generating test patterns for crosstalk faults on single victim due to multiple aggressors, the modified PODEM algorithm is found to be more time consuming. The search capability of Genetic Algorithms in finding the required combination of several input factors for any optimized problem fascinated to apply GA for generating test patterns as generating the test pattern is also similar to finding the required vector out of several input transitions. Initially the GA is applied for generating test patterns for stuck-at faults and compared the results with PODEM algorithm. As the fault coverage is almost similar to the deterministic algorithm PODEM, the GA developed for stuck-at faults is extended to find test patterns for crosstalk faults between single aggressor and single victim. The elitist GA is also applied for a few ISCAS 85 benchmark circuits. Later the algorithm is extended to generate test patterns for worst-case crosstalk faults. It has been proved that elitist GA developed in this thesis is also very useful in generating test patterns for crosstalk faults especially for multiple aggressor and single victim crosstalk faults

Maximizing Crosstalk-Induced Slowdown During Path Delay Test

Capacitive crosstalk between adjacent signal wires in integrated circuits may lead to noise or a speedup or slowdown in signal transitions. These in turn may lead to circuit failure or reduced operating speed. This thesis focuses on generating test patterns to induce crosstalk-induced signal delays, in order to determine whether the circuit can still meet its timing specification. A timing-driven test generator is developed to sensitize multiple aligned aggressors coupled to a delay-sensitive victim path to detect the combination of a delay spot defect and crosstalk-induced slowdown. The framework uses parasitic capacitance information, timing windows and crosstalk-induced delay estimates to screen out unaligned or ineffective aggressors coupled to a victim path, speeding up crosstalk pattern generation. In order to induce maximum crosstalk slowdown along a path, aggressors are prioritized based on their potential delay increase and timing alignment. The test generation engine introduces the concept of alignment-driven path sensitization to generate paths from inputs to coupled aggressor nets that meet timing alignment and direction requirements. By using path delay information obtained from circuit preprocessing, preferred paths can be chosen during aggressor path propagation processes. As the test generator sensitizes aggressors in the presence of victim path necessary assignments, the search space is effectively reduced for aggressor path generation. This helps in reducing the test generation time for aligned aggressors. In addition, two new crosstalk-driven dynamic test compaction algorithms are developed to control the increase in test pattern count. The proposed test generation algorithm is applied to ISCAS85 and ISCAS89 benchmark circuits. SPICE simulation results demonstrate the ability of the alignment-driven test generator to increase crosstalk-induced delays along victim paths

Structural Software-Based Self-Test of Network-on-Chip

Abstract—Software-Based Self-Test (SBST) is extended to the switches of complex Network-on-Chips (NoC). Test patterns for structural faults are turned into valid packets by using satisfiability (SAT) solvers. The test technique provides a high fault coverage for both manufacturing test and online test

Modeling defective part level due to static and dynamic defects based upon site observation and excitation balance

Manufacture testing of digital integrated circuits is essential for high quality. However, exhaustive testing is impractical, and only a small subset of all possible test patterns (or test pattern pairs) may be applied. Thus, it is crucial to choose a subset that detects a high percentage of the defective parts and produces a low defective part level. Historically, test pattern generation has often been seen as a deterministic endeavor. Test sets are generated to deterministically ensure that a large percentage of the targeted faults are detected. However, many real defects do not behave like these faults, and a test set that detects them all may still miss many defects. Unfortunately, modeling all possible defects as faults is impractical. Thus, it is important to fortuitously detect unmodeled defects using high quality test sets. To maximize fortuitous detection, we do not assume a high correlation between faults and actual defects. Instead, we look at the common requirements for all defect detection. We deterministically maximize the observations of the leastobserved sites while randomly exciting the defects that may be present. The resulting decrease in defective part level is estimated using the MPGD model. This dissertation describes the MPGD defective part level model and shows how it can be used to predict defective part levels resulting from static defect detection. Unlike many other predictors, its predictions are a function of site observations, not fault coverage, and thus it is generally more accurate at high fault coverages. Furthermore, its components model the physical realities of site observation and defect excitation, and thus it can be used to give insight into better test generation strategies. Next, we investigate the effect of additional constraints on the fortuitous detection of defects-specifically, as we focus on detecting dynamic defects instead of static ones. We show that the quality of the randomness of excitation becomes increasingly important as defect complexity increases. We introduce a new metric, called excitation balance, to estimate the quality of the excitation, and we show how excitation balance relates to the constant τ in the MPGD model

Improving timing verification and delay testing methodologies for IC designs

textThe task of ensuring the correct temporal behavior of IC designs, both before and after fabrication, is extremely important. It is becoming even more imperative as the demand for performance increases and process technology advances into the deep sub-micron region. This dissertation tackles the key issues in the timing verification and delay testing methodologies. An efficient methodology is presented to identify false timing paths in the timing verification methodology which utilizes ATPG technique and timing information from an ordered list of timing paths according to the delay information. This dissertation also presents a speed binning methodology which utilizes structural delay tests successfully instead of functional tests. In addition, it establishes a methodology which quantifies the correlation between the timing verification prediction and actual silicon measurement of timing paths. This quantification methodology lays the foundation for further research to study the impact of deep submicron effects on design performanceElectrical and Computer Engineerin

Design and test for timing uncertainty in VLSI circuits.

由於特徵尺寸不斷縮小，集成電路在生產過程中的工藝偏差在運行環境中溫度和電壓等參數的波動以及在使用過程中的老化等效應越來越嚴重，導致芯片的時序行為出現很大的不確定性。多數情況下，芯片的關鍵路徑會不時出現時序錯誤。加入更多的時序餘量不是一種很好的解決方案，因為這種保守的設計方法會抵消工藝進步帶來的性能上的好處。這就為設計一個時序可靠的系統提出了極大的挑戰，其中的一些關鍵問題包括：(一)如何有效地分配有限的功率預算去優化那些正爆炸式增加的關鍵路徑的時序性能；(二)如何產生能夠捕捉準確的最壞情況時延的高品質測試向量；(三)為了能夠取得更好的功耗和性能上的平衡，我們將不得不允許芯片在使用過程中出現一些頻率很低的時序錯誤。隨之而來的問題是如何做到在線的檢錯和糾錯。為了解決上述問題，我們首先發明了一種新的技術用於識別所謂的虛假路徑，該方法使我們能夠發現比傳統方法更多的虛假路徑。當將所提取的虛假路徑集成到靜態時序分析工具里以後，我們可以得到更為準確的時序分析結果，同時也能節省本來用於優化這些路徑的成本。接著，考慮到現有的延時自動向量生成(ATPG) 方法會產生功能模式下無法出現的測試向量，這種向量可能會造成測試過程中在被激活的路徑周圍出現過多(或過少)的電源噪聲(PSN) ，從而導致測試過度或者測試不足情況。為此，我們提出了一種新的偽功能ATPG工具。通過同時考慮功能約束以及電路的物理佈局信息，我們使用類似ATPG 的算法產生狀態跳變使其能最大化已激活的路徑周圍的PSN影響。最後，基於近似電路的原理，我們提出了一種新的在線原位校正技術，即InTimeFix，用於糾正時序錯誤。由於實現近似電路的綜合僅需要簡單的電路結構分析，因此該技術能夠很容易的擴展到大型電路設計上去。With technology scaling, integrated circuits (ICs) suffer from increasing process, voltage, and temperature (PVT) variations and aging effects. In most cases, these reliability threats manifest themselves as timing errors on speed-paths (i.e., critical or near-critical paths) of the circuit. Embedding a large design guard band to prevent timing errors to occur is not an attractive solution, since this conservative design methodology diminishes the benefit of technology scaling. This creates several challenges on build a reliable systems, and the key problems include (i) how to optimize circuit’s timing performance with limited power budget for explosively increased potential speed-paths; (ii) how to generate high quality delay test pattern to capture ICs’ accurate worst-case delay; (iii) to have better power and performance tradeoff, we have to accept some infrequent timing errors in circuit’s the usage phase. Therefore, the question is how to achieve online timing error resilience.To address the above issues, we first develop a novel technique to identify so-called false paths, which facilitate us to find much more false paths than conventional methods. By integrating our identified false paths into static timing analysis tool, we are able to achieve more accurate timing information and also save the cost used to optimize false paths. Then, due to the fact that existing delay automated test pattern generation (ATPG) methods may generate test patterns that are functionally-unreachable, and such patterns may incur excessive (or limited) power supply noise (PSN) on sensitized paths in test mode, thus leading to over-testing or under-testing of the circuits, we propose a novel pseudo-functional ATPG tool. By taking both circuit layout information and functional constrains into account, we use ATPG like algorithm to justify transitions that pose the maximized functional PSN effects on sensitized critical paths. Finally, we propose a novel in-situ correction technique to mask timing errors, namely InTimeFix, by introducing redundant approximation circuit with more timing slack for speed-paths into the design. The synthesis of the approximation circuit relies on simple structural analysis of the original circuit, which is easily scalable to large IC designs.Detailed summary in vernacular field only.Detailed summary in vernacular field only.Yuan, Feng.Thesis (Ph.D.)--Chinese University of Hong Kong, 2012.Includes bibliographical references (leaves 88-100).Abstract also in Chinese.Abstract --- p.iAcknowledgement --- p.ivChapter 1 --- Introduction --- p.1Chapter 1.1 --- Challenges to Solve Timing Uncertainty Problem --- p.2Chapter 1.2 --- Contributions and Thesis Outline --- p.5Chapter 2 --- Background --- p.7Chapter 2.1 --- Sources of Timing Uncertainty --- p.7Chapter 2.1.1 --- Process Variation --- p.7Chapter 2.1.2 --- Runtime Environment Fluctuation --- p.9Chapter 2.1.3 --- Aging Effect --- p.10Chapter 2.2 --- Technical Flow to Solve Timing Uncertainty Problem --- p.10Chapter 2.3 --- False Path --- p.12Chapter 2.3.1 --- Path Sensitization Criteria --- p.12Chapter 2.3.2 --- False Path Aware Timing Analysis --- p.13Chapter 2.4 --- Manufacturing Testing --- p.14Chapter 2.4.1 --- Functional Testing vs. Structural Testing --- p.14Chapter 2.4.2 --- Scan-Based DfT --- p.15Chapter 2.4.3 --- Pseudo-Functional Testing --- p.17Chapter 2.5 --- Timing Error Tolerance --- p.19Chapter 2.5.1 --- Timing Error Detection --- p.19Chapter 2.5.2 --- Timing Error Recover --- p.20Chapter 3 --- Timing-Independent False Path Identification --- p.23Chapter 3.1 --- Introduction --- p.23Chapter 3.2 --- Preliminaries and Motivation --- p.26Chapter 3.2.1 --- Motivation --- p.27Chapter 3.3 --- False Path Examination Considering Illegal States --- p.28Chapter 3.3.1 --- Path Sensitization Criterion --- p.28Chapter 3.3.2 --- Path-Aware Illegal State Identification --- p.30Chapter 3.3.3 --- Proposed Examination Procedure --- p.31Chapter 3.4 --- False Path Identification --- p.32Chapter 3.4.1 --- Overall Flow --- p.34Chapter 3.4.2 --- Static Implication Learning --- p.35Chapter 3.4.3 --- Suspicious Node Extraction --- p.36Chapter 3.4.4 --- S-Frontier Propagation --- p.37Chapter 3.5 --- Experimental Results --- p.38Chapter 3.6 --- Conclusion and Future Work --- p.42Chapter 4 --- PSN Aware Pseudo-Functional Delay Testing --- p.43Chapter 4.1 --- Introduction --- p.43Chapter 4.2 --- Preliminaries and Motivation --- p.45Chapter 4.2.1 --- Motivation --- p.46Chapter 4.3 --- Proposed Methodology --- p.48Chapter 4.4 --- Maximizing PSN Effects under Functional Constraints --- p.50Chapter 4.4.1 --- Pseudo-Functional Relevant Transitions Generation --- p.51Chapter 4.5 --- Experimental Results --- p.59Chapter 4.5.1 --- Experimental Setup --- p.59Chapter 4.5.2 --- Results and Discussion --- p.60Chapter 4.6 --- Conclusion --- p.64Chapter 5 --- In-Situ Timing Error Masking in Logic Circuits --- p.65Chapter 5.1 --- Introduction --- p.65Chapter 5.2 --- Prior Work and Motivation --- p.67Chapter 5.3 --- In-Situ Timing Error Masking with Approximate Logic --- p.69Chapter 5.3.1 --- Equivalent Circuit Construction with Approximate Logic --- p.70Chapter 5.3.2 --- Timing Error Masking with Approximate Logic --- p.72Chapter 5.4 --- Cost-Efficient Synthesis for InTimeFix --- p.75Chapter 5.4.1 --- Overall Flow --- p.76Chapter 5.4.2 --- Prime Critical Segment Extraction --- p.77Chapter 5.4.3 --- Prime Critical Segment Merging --- p.79Chapter 5.5 --- Experimental Results --- p.81Chapter 5.5.1 --- Experimental Setup --- p.81Chapter 5.5.2 --- Results and Discussion --- p.82Chapter 5.6 --- Conclusion --- p.85Chapter 6 --- Conclusion and Future Work --- p.86Bibliography --- p.10