On the Use of Reciprocal Filter against WiFi Packets for Passive Radar

This paper aims at a critical review of the signal processing scheme used in WiFi-based passive radar in order to limit its complexity and enhance its suitability for short range civilian applications. To this purpose the exploitation of a reciprocal filtering strategy is investigated as an alternative to conventional matched filtering at the range compression stage. Along with the well-known advantage of a remarkable sidelobes control capability for the resulting range-Doppler response, the use of a reciprocal filter is shown to provide additional benefits for the specific sensor subject of this study. Specifically, it allows to streamline the disturbance cancellation stage and to implement a unified signal processing architecture which is capable to handle the different modulation schemes typically adopted in WiFi transmissions. Appropriate adjustments are also proposed to the theoretical reciprocal filter in order to cope with the inherent loss in term of signal-to-noise power ratio. The effectiveness of the revised signal processing scheme encompassing the reciprocal filtering strategy is proved against both simulated and experimental datasets

Joint Compressed Sensing and Manipulation of Wireless Emissions with Intelligent Surfaces

Programmable, intelligent surfaces can manipulate electromagnetic waves impinging upon them, producing arbitrarily shaped reflection, refraction and diffraction, to the benefit of wireless users. Moreover, in their recent form of HyperSurfaces, they have acquired inter-networking capabilities, enabling the Internet of Material Properties with immense potential in wireless communications. However, as with any system with inputs and outputs, accurate sensing of the impinging wave attributes is imperative for programming HyperSurfaces to obtain a required response. Related solutions include field nano-sensors embedded within HyperSurfaces to perform minute measurements over the area of the HyperSurface, as well as external sensing systems. The present work proposes a sensing system that can operate without such additional hardware. The novel scheme programs the HyperSurface to perform compressed sensing of the impinging wave via simple one-antenna power measurements. The HyperSurface can jointly be programmed for both wave sensing and wave manipulation duties at the same time. Evaluation via simulations validates the concept and highlight its promising potential.Comment: Published at IEEE DCOSS 2019 / IoT4.0 workshop (https://www.dcoss.org/workshops.html). Funded by the European Union via the Horizon 2020: Future Emerging Topics - Research and Innovation Action call (FETOPEN-RIA), grant EU736876, project VISORSURF (http://www.visorsurf.eu

Using Radio Frequency and Motion Sensing to Improve Camera Sensor Systems

Camera-based sensor systems have advanced significantly in recent years. This advancement is a combination of camera CMOS (complementary metal-oxide-semiconductor) hardware technology improvement and new computer vision (CV) algorithms that can better process the rich information captured. As the world becoming more connected and digitized through increased deployment of various sensors, cameras have become a cost-effective solution with the advantages of small sensor size, intuitive sensing results, rich visual information, and neural network-friendly. The increased deployment and advantages of camera-based sensor systems have fueled applications such as surveillance, object detection, person re-identification, scene reconstruction, visual tracking, pose estimation, and localization. However, camera-based sensor systems have fundamental limitations such as extreme power consumption, privacy-intrusive, and inability to see-through obstacles and other non-ideal visual conditions such as darkness, smoke, and fog. In this dissertation, we aim to improve the capability and performance of camera-based sensor systems by utilizing additional sensing modalities such as commodity WiFi and mmWave (millimeter wave) radios, and ultra-low-power and low-cost sensors such as inertial measurement units (IMU). In particular, we set out to study three problems: (1) power and storage consumption of continuous-vision wearable cameras, (2) human presence detection, localization, and re-identification in both indoor and outdoor spaces, and (3) augmenting the sensing capability of camera-based systems in non-ideal situations. We propose to use an ultra-low-power, low-cost IMU sensor, along with readily available camera information, to solve the first problem. WiFi devices will be utilized in the second problem, where our goal is to reduce the hardware deployment cost and leverage existing WiFi infrastructure as much as possible. Finally, we will use a low-cost, off-the-shelf mmWave radar to extend the sensing capability of a camera in non-ideal visual sensing situations.Doctor of Philosoph

Device Free Localisation Techniques in Indoor Environments

The location estimation of a target for a long period was performed only by device based localisation technique which is difficult in applications where target especially human is non-cooperative. A target was detected by equipping a device using global positioning systems, radio frequency systems, ultrasonic frequency systems, etc. Device free localisation (DFL) is an upcoming technology in automated localisation in which target need not equip any device for identifying its position by the user. For achieving this objective, the wireless sensor network is a better choice due to its growing popularity. This paper describes the possible categorisation of recently developed DFL techniques using wireless sensor network. The scope of each category of techniques is analysed by comparing their potential benefits and drawbacks. Finally, future scope and research directions in this field are also summarised

Multiple Sparse Measurement Gradient Reconstruction Algorithm for DOA Estimation in Compressed Sensing

A novel direction of arrival (DOA) estimation method in compressed sensing (CS) is proposed, in which the DOA estimation problem is cast as the joint sparse reconstruction from multiple measurement vectors (MMV). The proposed method is derived through transforming quadratically constrained linear programming (QCLP) into unconstrained convex optimization which overcomes the drawback that l1-norm is nondifferentiable when sparse sources are reconstructed by minimizing l1-norm. The convergence rate and estimation performance of the proposed method can be significantly improved, since the steepest descent step and Barzilai-Borwein step are alternately used as the search step in the unconstrained convex optimization. The proposed method can obtain satisfactory performance especially in these scenarios with low signal to noise ratio (SNR), small number of snapshots, or coherent sources. Simulation results show the superior performance of the proposed method as compared with existing methods

Passive Synthetic Aperture Radar Imaging Using Commercial OFDM Communication Networks

Modern communication systems provide myriad opportunities for passive radar applications. OFDM is a popular waveform used widely in wireless communication networks today. Understanding the structure of these networks becomes critical in future passive radar systems design and concept development. This research develops collection and signal processing models to produce passive SAR ground images using OFDM communication networks. The OFDM-based WiMAX network is selected as a relevant example and is evaluated as a viable source for radar ground imaging. The monostatic and bistatic phase history models for OFDM are derived and validated with experimental single dimensional data. An airborne passive collection model is defined and signal processing approaches are proposed providing practical solutions to passive SAR imaging scenarios. Finally, experimental SAR images using general OFDM and WiMAX waveforms are shown to validate the overarching signal processing concept