Packet level measurement over wireless access

PhDPerformance Measurement of the IP packet networks mainly comprise of monitoring the network performance in terms of packet losses and delays. If used appropriately, these network parameters (i.e. delay, loss and bandwidth etc) can indicate the performance status of the network and they can be used in fault and performance monitoring, network provisioning, and traffic engineering. Globally, there is a growing need for accurate network measurement to support the commercial use of IP networks. In wireless networks, transmission losses and communication delays strongly affect the performance of the network. Compared to wired networks, wireless networks experience higher levels of data dropouts, and corruption due to issues of channel fading, noise, interference and mobility. Performance monitoring is a vital element in the commercial future of broadband packet networking and the ability to guarantee quality of service in such networks is implicit in Service Level Agreements. Active measurements are performed by injecting probes, and this is widely used to determine the end to end performance. End to end delay in wired networks has been extensively investigated, and in this thesis we report on the accuracy achieved by probing for end to end delay over a wireless scenario. We have compared two probing techniques i.e. Periodic and Poisson probing, and estimated the absolute error for both. The simulations have been performed for single hop and multi- hop wireless networks. In addition to end to end latency, Active measurements have also been performed for packet loss rate. The simulation based analysis has been tried under different traffic scenarios using Poisson Traffic Models. We have sampled the user traffic using Periodic probing at different rates for single hop and multiple hop wireless scenarios. 5 Active probing becomes critical at higher values of load forcing the network to saturation much earlier. We have evaluated the impact of monitoring overheads on the user traffic, and show that even small amount of probing overhead in a wireless medium can cause large degradation in network performance. Although probing at high rate provides a good estimation of delay distribution of user traffic with large variance yet there is a critical tradeoff between the accuracy of measurement and the packet probing overhead. Our results suggest that active probing is highly affected by probe size, rate, pattern, traffic load, and nature of shared medium, available bandwidth and the burstiness of the traffic

Prediction of sorption enhanced steam methane reforming products from machine learning based soft-sensor models

Carbon dioxide-abated hydrogen can be synthesised via various processes, one of which is sorption enhanced steam methane reforming (SE-SMR), which produces separated streams of high purity H2 and CO2. Properties of hydrogen and the sorbent material hinder the ability to rapidly upscale SE-SMR, therefore the use of artificial intelligence models is useful in order to assist scale up. Advantages of a data driven soft-sensor model over thermodynamic simulations, is the ability to obtain real time information dependent on actual process conditions. In this study, two soft sensor models have been developed and used to predict and estimate variables that would otherwise be difficult direct measured. Both artificial neural networks and the random forest models were developed as soft sensor prediction models. They were shown to provide good predictions for gas concentrations in the reformer and regenerator reactors of the SE-SMR process using temperature, pressure, steam to carbon ratio and sorbent to carbon ratio as input process features. Both models were very accurate with high R2 values, all above 98%. However, the random forest model was more precise in the predictions, with consistently higher R2 values and lower mean absolute error (0.002-0.014) compared to the neural network model (0.005-0.024)

A slotted-CDMA based wireless-ATM link layer : guaranteeing QoS over a wireless link.

Thesis (M.Sc.)-University of Natal, Durban, 2000.Future wireless networks will have to handle varying combinations of multimedia traffic that present the network with numerous quality of service (QoS) requirements. The continuously growing demand for mobile phones has resulted in radio spectrum becoming a precious resource that cannot be wasted. The current second-generation mobile networks are designed for voice communication and, even with the enhancements being implemented to accommodate data, they cannot efficiently handle the multimedia traffic demands that will be introduced in the near future. This thesis begins with a survey of existing wireless ATM (WATM) protocols, followed by an examination of some medium access control (MAC) protocols, supporting multimedia traffic, and based on code division multiple access (CDMA) physical layers. A WATM link layer protocol based on a CDMA physical layer, and incorporating techniques from some of the surveyed protocols, is then proposed. The MAC protocol supports a wide range of service requirements by utilising a flexible scheduling algorithm that takes advantage of the graceful degradation of CDMA with increasing user interference to schedule cells for transmission according to their maximum bit error rate (BER) requirements. The data link control (DLC) accommodates the various traffic types by allowing virtual channels (VCs) to make use of forward error correction (FEc) or retransmission techniques. The proposed link layer protocol has been implemented on a Blue Wave Systems DSP board that forms part of Alcatel Altech Telecoms' software radio platform. The details and practicality of the implementation are presented. A simulation model for the protocol has been developed using MIL3 's Opnet Modeler. Hence, both simulated and measured performance results are presented before the thesis concludes with suggestions for improvements and future work

Journal of Telecommunications and Information Technology, 2011, nr 3

kwartalni

Intelligent sensing for robot mapping and simultaneous human localization and activity recognition

Ankara : The Department of Electrical and Electronics Engineering and the Institute of Engineering and Science of Bilkent University, 2011.Thesis (Ph. D.) -- Bilkent University, 2011.Includes bibliographical references leaves 147-163.We consider three different problems in two different sensing domains, namely ultrasonic sensing and inertial sensing. Since the applications considered in each domain are inherently different, this thesis is composed of two main parts. The approach common to the two parts is that raw data acquired from simple sensors is processed intelligently to extract useful information about the environment. In the first part, we employ active snake contours and Kohonen’s selforganizing feature maps (SOMs) for representing and evaluating discrete point maps of indoor environments efficiently and compactly. We develop a generic error criterion for comparing two different sets of points based on the Euclidean distance measure. The point sets can be chosen as (i) two different sets of map points acquired with different mapping techniques or different sensing modalities, (ii) two sets of fitted curve points to maps extracted by different mapping techniques or sensing modalities, or (iii) a set of extracted map points and a set of fitted curve points. The error criterion makes it possible to compare the accuracy of maps obtained with different techniques among themselves, as well as with an absolute reference. We optimize the parameters of active snake contours and SOMs using uniform sampling of the parameter space and particle swarm optimization. A demonstrative example from ultrasonic mapping is given based on experimental data and compared with a very accurate laser map, considered an absolute reference. Both techniques can fill the erroneous gaps in discrete point maps. Snake curve fitting results in more accurate maps than SOMs because it is more robust to outliers. The two methods and the error criterion are sufficiently general that they can also be applied to discrete point maps acquired with other mapping techniques and other sensing modalities. In the second part, we use body-worn inertial/magnetic sensor units for recognition of daily and sports activities, as well as for human localization in GPSdenied environments. Each sensor unit comprises a tri-axial gyroscope, a tri-axial accelerometer, and a tri-axial magnetometer. The error characteristics of the sensors are modeled using the Allan variance technique, and the parameters of lowand high-frequency error components are estimated. Then, we provide a comparative study on the different techniques of classifying human activities that are performed using body-worn miniature inertial and magnetic sensors. Human activities are classified using five sensor units worn on the chest, the arms, and the legs. We compute a large number of features extracted from the sensor data, and reduce these features using both Principal Components Analysis (PCA) and sequential forward feature selection (SFFS). We consider eight different pattern recognition techniques and provide a comparison in terms of the correct classification rates, computational costs, and their training and storage requirements. Results with sensors mounted on various locations on the body are also provided. The results indicate that if the system is trained by the data of an individual person, it is possible to obtain over 99% correct classification rates with a simple quadratic classifier such as the Bayesian decision method. However, if the training data of that person are not available beforehand, one has to resort to more complex classifiers with an expected correct classification rate of about 85%. We also consider the human localization problem using body-worn inertial/ magnetic sensors. Inertial sensors are characterized by drift error caused by the integration of their rate output to get position information. Because of this drift, the position and orientation data obtained from inertial sensor signals are reliable over only short periods of time. Therefore, position updates from externally referenced sensors are essential. However, if the map of the environment is known, the activity context of the user provides information about position. In particular, the switches in the activity context correspond to discrete locations on the map. By performing activity recognition simultaneously with localization, one can detect the activity context switches and use the corresponding position information as position updates in the localization filter. The localization filter also involves a smoother, which combines the two estimates obtained by running the zero-velocity update (ZUPT) algorithm both forward and backward in time. We performed experiments with eight subjects in an indoor and an outdoor environment involving “walking,” “turning,” and “standing” activities. Using the error criterion in the first part of the thesis, we show that the position errors can be decreased by about 85% on the average. We also present the results of a 3-D experiment performed in a realistic indoor environment and demonstrate that it is possible to achieve over 90% error reduction in position by performing activity recognition simultaneously with localization.Altun, KeremPh.D

Combining SOA and BPM Technologies for Cross-System Process Automation

This paper summarizes the results of an industry case study that introduced a cross-system business process automation solution based on a combination of SOA and BPM standard technologies (i.e., BPMN, BPEL, WSDL). Besides discussing major weaknesses of the existing, custom-built, solution and comparing them against experiences with the developed prototype, the paper presents a course of action for transforming the current solution into the proposed solution. This includes a general approach, consisting of four distinct steps, as well as specific action items that are to be performed for every step. The discussion also covers language and tool support and challenges arising from the transformation

University of Minnesota-Morris Bulletin 1997-1999

https://digitalcommons.morris.umn.edu/catalog/1032/thumbnail.jp