Design Techniques for High-Performance SAR A/D Converters

The design of electronics needs to account for the non-ideal characteristics of the device technologies used to realize practical circuits. This is particularly important in mixed analog-digital design since the best device technologies are very different for digital compared to analog circuits. One solution for this problem is to use a calibration correction approach to remove the errors introduced by devices, but this adds complexity and power dissipation, as well as reducing operation speed, and so must be optimised. This thesis addresses such an approach to improve the performance of certain types of analog-to-digital converter (ADC) used in advanced telecommunications, where speed, accuracy and power dissipation currently limit applications. The thesis specifically focuses on the design of compensation circuits for use in successive approximation register (SAR) ADCs. ADCs are crucial building blocks in communication systems, in general, and for mobile networks, in particular. The recently launched fifth generation of mobile networks (5G) has required new ADC circuit techniques to meet the higher speed and lower power dissipation requirements for 5G technology. The SAR has become one of the most favoured architectures for designing high-performance ADCs, but the successive nature of the circuit operation makes it difficult to reach ∼GS/s sampling rates at reasonable power consumption. Here, two calibration techniques for high-performance SAR ADCs are presented. The first uses an on-chip stochastic-based mismatch calibration technique that is able to accurately compute and compensate for the mismatch of a capacitive DAC in a SAR ADC. The stochastic nature of the proposed calibration method enables determination of the mismatch of the CAPDAC with a resolution much better than that of the DAC. This allows the unit capacitor to scale down to as low as 280aF for a 9-bit DAC. Since the CAP-DAC causes a large part of the overall dynamic power consumption and directly determines both the sizes of the driving and sampling switches and the size of the input capacitive load of the ADC and the kT/C noise power, a small CAP-DAC helps the power efficiency. To validate the proposed calibration idea, a 10-bit asynchronous SAR ADC was fabricated in 28-nm CMOS. Measurement results show that the proposed stochastic calibration improves the ADC’s SFDR and SNDR by 14.9 dB, 11.5 dB, respectively. After calibration, the fabricated SAR ADC achieves an ENOB of 9.14 bit at a sampling rate of 85 MS/s, resulting in a Walden FoM of 10.9 fJ/c-s. The second calibration technique is a timing-skew calibration for a time-interleaved (TI) SAR ADC that calibrates/computes the inter-channel timing and offset mismatch simultaneously. Simulation results show the effectiveness of this calibration method. When used together, the proposed mismatch calibration technique and the timing-skew calibration technique enables a TI SAR ADC to be designed that can achieve a sampling rate of ∼GS/s with 10-bit resolution and a power consumption as low as ∼10mW; specifications that satisfy the requirements of 5G technology

A built-in self-test technique for high speed analog-to-digital converters

Fundação para a Ciência e a Tecnologia (FCT) - PhD grant (SFRH/BD/62568/2009

Design and debugging of multi-step analog to digital converters

With the fast advancement of CMOS fabrication technology, more and more signal-processing functions are implemented in the digital domain for a lower cost, lower power consumption, higher yield, and higher re-configurability. The trend of increasing integration level for integrated circuits has forced the A/D converter interface to reside on the same silicon in complex mixed-signal ICs containing mostly digital blocks for DSP and control. However, specifications of the converters in various applications emphasize high dynamic range and low spurious spectral performance. It is nontrivial to achieve this level of linearity in a monolithic environment where post-fabrication component trimming or calibration is cumbersome to implement for certain applications or/and for cost and manufacturability reasons. Additionally, as CMOS integrated circuits are accomplishing unprecedented integration levels, potential problems associated with device scaling – the short-channel effects – are also looming large as technology strides into the deep-submicron regime. The A/D conversion process involves sampling the applied analog input signal and quantizing it to its digital representation by comparing it to reference voltages before further signal processing in subsequent digital systems. Depending on how these functions are combined, different A/D converter architectures can be implemented with different requirements on each function. Practical realizations show the trend that to a first order, converter power is directly proportional to sampling rate. However, power dissipation required becomes nonlinear as the speed capabilities of a process technology are pushed to the limit. Pipeline and two-step/multi-step converters tend to be the most efficient at achieving a given resolution and sampling rate specification. This thesis is in a sense unique work as it covers the whole spectrum of design, test, debugging and calibration of multi-step A/D converters; it incorporates development of circuit techniques and algorithms to enhance the resolution and attainable sample rate of an A/D converter and to enhance testing and debugging potential to detect errors dynamically, to isolate and confine faults, and to recover and compensate for the errors continuously. The power proficiency for high resolution of multi-step converter by combining parallelism and calibration and exploiting low-voltage circuit techniques is demonstrated with a 1.8 V, 12-bit, 80 MS/s, 100 mW analog to-digital converter fabricated in five-metal layers 0.18-µm CMOS process. Lower power supply voltages significantly reduce noise margins and increase variations in process, device and design parameters. Consequently, it is steadily more difficult to control the fabrication process precisely enough to maintain uniformity. Microscopic particles present in the manufacturing environment and slight variations in the parameters of manufacturing steps can all lead to the geometrical and electrical properties of an IC to deviate from those generated at the end of the design process. Those defects can cause various types of malfunctioning, depending on the IC topology and the nature of the defect. To relive the burden placed on IC design and manufacturing originated with ever-increasing costs associated with testing and debugging of complex mixed-signal electronic systems, several circuit techniques and algorithms are developed and incorporated in proposed ATPG, DfT and BIST methodologies. Process variation cannot be solved by improving manufacturing tolerances; variability must be reduced by new device technology or managed by design in order for scaling to continue. Similarly, within-die performance variation also imposes new challenges for test methods. With the use of dedicated sensors, which exploit knowledge of the circuit structure and the specific defect mechanisms, the method described in this thesis facilitates early and fast identification of excessive process parameter variation effects. The expectation-maximization algorithm makes the estimation problem more tractable and also yields good estimates of the parameters for small sample sizes. To allow the test guidance with the information obtained through monitoring process variations implemented adjusted support vector machine classifier simultaneously minimize the empirical classification error and maximize the geometric margin. On a positive note, the use of digital enhancing calibration techniques reduces the need for expensive technologies with special fabrication steps. Indeed, the extra cost of digital processing is normally affordable as the use of submicron mixed signal technologies allows for efficient usage of silicon area even for relatively complex algorithms. Employed adaptive filtering algorithm for error estimation offers the small number of operations per iteration and does not require correlation function calculation nor matrix inversions. The presented foreground calibration algorithm does not need any dedicated test signal and does not require a part of the conversion time. It works continuously and with every signal applied to the A/D converter. The feasibility of the method for on-line and off-line debugging and calibration has been verified by experimental measurements from the silicon prototype fabricated in standard single poly, six metal 0.09-µm CMOS process

Doctor of Philosophy

dissertationSince the late 1950s, scientists have been working toward realizing implantable devices that would directly monitor or even control the human body's internal activities. Sophisticated microsystems are used to improve our understanding of internal biological processes in animals and humans. The diversity of biomedical research dictates that microsystems must be developed and customized specifically for each new application. For advanced long-term experiments, a custom designed system-on-chip (SoC) is usually necessary to meet desired specifications. Custom SoCs, however, are often prohibitively expensive, preventing many new ideas from being explored. In this work, we have identified a set of sensors that are frequently used in biomedical research and developed a single-chip integrated microsystem that offers the most commonly used sensor interfaces, high computational power, and which requires minimum external components to operate. Included peripherals can also drive chemical reactions by setting the appropriate voltages or currents across electrodes. The SoC is highly modular and well suited for prototyping in and ex vivo experimental devices. The system runs from a primary or secondary battery that can be recharged via two inductively coupled coils. The SoC includes a 16-bit microprocessor with 32 kB of on chip SRAM. The digital core consumes 350 μW at 10 MHz and is capable of running at frequencies up to 200 MHz. The integrated microsystem has been fabricated in a 65 nm CMOS technology and the silicon has been fully tested. Integrated peripherals include two sigma-delta analog-to-digital converters, two 10-bit digital-to-analog converters, and a sleep mode timer. The system also includes a wireless ultra-wideband (UWB) transmitter. The fullydigital transmitter implementation occupies 68 x 68 μm2 of silicon area, consumes 0.72 μW static power, and achieves an energy efficiency of 19 pJ/pulse at 200 MHz pulse repetition frequency. An investigation of the suitability of the UWB technology for neural recording systems is also presented. Experimental data capturing the UWB signal transmission through an animal head are presented and a statistical model for large-scale signal fading is developed

Digital signal processing for segmented HPGe detectors preprocessingalgorithms and pulse shape analysis

MINIBALL is an versatile spectrometer consisting of 24 longitudinally six-fold segmented HPGe detectors, build for the efficient detection of rare γ decays in nuclear reactions of radioactive ion beams. MINIBALL was the first spectrometer equipped with digital electronics. Pulse shape analysis algorithms to determine the interaction position of γ -rays were implemented on a Digital Signal Processor and validated in an experiment using a collimated γ -ray source. Emphasis was placed on the properties of the different digital signal processing algorithms, the consequences for the implementation and the applicability for position determination. The next generation of γ -ray spectrometers will consist of highly segmented HPGe detectors equipped with digital electronics, resulting in a more than ten-fold increase in complexity compared to current spectrometers. To enable the construction of a γ -ray tracking spectrometer, new and powerful digital electronics will be developed. Preprocessing algorithms, giving the γ -ray energy and generating event triggers, were implemented on a VME module equipped with fast A/D converters and tested with different detectors and sources. Emphasis was placed on the detailed simulation and understanding of the algorithms as well as the influence of electronics and detector onto the energy resolution

Architectural Alternatives to Implement High-Performance Delta-Sigma Modulators

RÉSUMÉ Le besoin d’appareils portatifs, de téléphones intelligents et de systèmes microélectroniques implantables médicaux s’accroît remarquablement. Cependant, l’optimisation de l’alimentation de tous ces appareils électroniques portables est l’un des principaux défis en raison du manque de piles à grande capacité utilisées pour les alimenter. C’est un fait bien établi que le convertisseur analogique-numérique (CAN) est l’un des blocs les plus critiques de ces appareils et qu’il doit convertir efficacement les signaux analogiques au monde numérique pour effectuer un post-traitement tel que l’extraction de caractéristiques. Parmi les différents types de CAN, les modulateurs Delta Sigma (��M) ont été utilisés dans ces appareils en raison des fonctionnalités alléchantes qu’ils offrent. En raison du suréchantillonnage et pour éloigner le bruit de la bande d’intérêt, un CAN haute résolution peut être obtenu avec les architectures ��. Il offre également un compromis entre la fréquence d’échantillonnage et la résolution, tout en offrant une architecture programmable pour réaliser un CAN flexible. Ces CAN peuvent être implémentés avec des blocs analogiques de faible précision. De plus, ils peuvent être efficacement optimisés au niveau de l’architecture et circuits correspondants. Cette dernière caractéristique a été une motivation pour proposer différentes architectures au fil des ans. Cette thèse contribue à ce sujet en explorant de nouvelles architectures pour optimiser la structure ��M en termes de résolution, de consommation d’énergie et de surface de silicium. Des soucis particuliers doivent également être pris en compte pour faciliter la mise en œuvre du ��M. D’autre part, les nouveaux procédés CMOS de conception et fabrication apportent des améliorations remarquables en termes de vitesse, de taille et de consommation d’énergie lors de la mise en œuvre de circuits numériques. Une telle mise à l’échelle agressive des procédés, rend la conception de blocs analogiques tel que un amplificateur de transconductance opérationnel (OTA), difficile. Par conséquent, des soins spéciaux sont également pris en compte dans cette thèse pour surmonter les problèmes énumérés. Ayant mentionné ci-dessus que cette thèse est principalement composée de deux parties principales. La première concerne les nouvelles architectures implémentées en mode de tension et la seconde partie contient une nouvelle architecture réalisée en mode hybride tension et temps.----------ABSTRACT The need for hand-held devices, smart-phones and medical implantable microelectronic sys-tems, is remarkably growing up. However, keeping all these electronic devices power optimized is one of the main challenges due to the lack of long life-time batteries utilized to power them up. It is a well-established fact that analog-to-digital converter (ADC) is one of the most critical building blocks of such devices and it needs to efficiently convert analog signals to the digital world to perform post processing such as channelizing, feature extraction, etc. Among various type of ADCs, Delta Sigma Modulators (��Ms) have been widely used in those devices due to the tempting features they offer. In fact, due to oversampling and noise-shaping technique a high-resolution ADC can be achieved with �� architectures. It also offers a compromise between sampling frequency and resolution while providing a highly-programmable approach to realize an ADC. Moreover, such ADCs can be implemented with low-precision analog blocks. Last but not the least, they are capable of being effectively power optimized at both architectural and circuit levels. The latter has been a motivation to proposed different architectures over the years.This thesis contributes to this topic by exploring new architectures to effectively optimize the ��M structure in terms of resolution, power consumption and chip area. Special cares must also be taken into account to ease the implementation of the ��M. On the other hand, advanced node CMOS processes bring remarkable improvements in terms of speed, size and power consumption while implementing digital circuits. Such an aggressive process scaling, however, make the design of analog blocks, e.g. operational transconductance amplifiers (OTAs), cumbersome. Therefore, special cares are also taken into account in this thesis to overcome the mentioned issues. Having had above mentioned discussion, this thesis is mainly split in two main categories. First category addresses new architectures implemented in a pure voltage domain and the second category contains new architecture realized in a hybrid voltage and time domain. In doing so, the thesis first focuses on a switched-capacitor implementation of a ��M while presenting an architectural solution to overcome the limitations of the previous approaches. This limitations include a power hungry adder in a conventional feed-forward topology as well as power hungry OTAs

Integrated Circuits and Systems for Smart Sensory Applications

Connected intelligent sensing reshapes our society by empowering people with increasing new ways of mutual interactions. As integration technologies keep their scaling roadmap, the horizon of sensory applications is rapidly widening, thanks to myriad light-weight low-power or, in same cases even self-powered, smart devices with high-connectivity capabilities. CMOS integrated circuits technology is the best candidate to supply the required smartness and to pioneer these emerging sensory systems. As a result, new challenges are arising around the design of these integrated circuits and systems for sensory applications in terms of low-power edge computing, power management strategies, low-range wireless communications, integration with sensing devices. In this Special Issue recent advances in application-specific integrated circuits (ASIC) and systems for smart sensory applications in the following five emerging topics: (I) dedicated short-range communications transceivers; (II) digital smart sensors, (III) implantable neural interfaces, (IV) Power Management Strategies in wireless sensor nodes and (V) neuromorphic hardware

Direct digital synthesizers : theory, design and applications

Traditional designs of high bandwidth frequency synthesizers employ the use of a phase-locked-loop (PLL). A direct digital synthesizer (DDS) provides many significant advantages over the PLL approaches. Fast settling time, sub-Hertz frequency resolution, continuous-phase switching response and low phase noise are features easily obtainable in the DDS systems. Although the principle of the DDS has been known for many years, the DDS did not play a dominant role in wideband frequency generation until recent years. Earlier DDSs were limited to produce narrow bands of closely spaced frequencies, due to limitations of digital logic and D/A-converter technologies. Recent advantages in integrated circuit (IC) technologies have brought about remarkable progress in this area. By programming the DDS, adaptive channel bandwidths, modulation formats, frequency hopping and data rates are easily achieved. This is an important step towards a "software-radio" which can be used in various systems. The DDS could be applied in the modulator or demodulator in the communication systems. The applications of DDS are restricted to the modulator in the base station. The aim of this research was to find an optimal front-end for a transmitter by focusing on the circuit implementations of the DDS, but the research also includes the interface to baseband circuitry and system level design aspects of digital communication systems. The theoretical analysis gives an overview of the functioning of DDS, especially with respect to noise and spurs. Different spur reduction techniques are studied in detail. Four ICs, which were the circuit implementations of the DDS, were designed. One programmable logic device implementation of the CORDIC based quadrature amplitude modulation (QAM) modulator was designed with a separate D/A converter IC. For the realization of these designs some new building blocks, e.g. a new tunable error feedback structure and a novel and more cost-effective digital power ramp generator, were developed.reviewe