Optimal Universal Controllers for Roll Stabilization

Roll stabilization is an important problem of ship motion control. This problem becomes especially difficult if the same set of actuators (e.g. a single rudder) has to be used for roll stabilization and heading control of the vessel, so that the roll stabilizing system interferes with the ship autopilot. Finding the "trade-off" between the concurrent goals of accurate vessel steering and roll stabilization usually reduces to an optimization problem, which has to be solved in presence of an unknown wave disturbance. Standard approaches to this problem (loop-shaping, LQG, $H_{\infty}$-control etc.) require to know the spectral density of the disturbance, considered to be a \colored noise". In this paper, we propose a novel approach to optimal roll stabilization, approximating the disturbance by a polyharmonic signal with known frequencies yet uncertain amplitudes and phase shifts. Linear quadratic optimization problems in presence of polyharmonic disturbances can be solved by means of the theory of universal controllers developed by V.A. Yakubovich. An optimal universal controller delivers the optimal solution for any uncertain amplitudes and phases. Using Marine Systems Simulator (MSS) Toolbox that provides a realistic vessel's model, we compare our design method with classical approaches to optimal roll stabilization. Among three controllers providing the same quality of yaw steering, OUC stabilizes the roll motion most efficiently

Rudder roll stabilization for ships

This paper describes the design of an autopilot for rudder roll stabilization for ships. This autopilot uses the rudder not only for course keeping but also for reduction of the roll. The system has a series of properties which make the controller design far from straightforward: the process has only one input (the rudder angle) and two outputs (the heading and the roll angle); the transfer from rudder to roll is non-minimum-phase; because large and high-frequency rudder motions are necessary, the non-linearities of the steering machine cannot be disregarded; the disturbances caused by the waves vary considerably in amplitude and frequency spectrum.\ud \ud In order to solve these problems a new approach to the LQG method has been developed. The control algorithms were tested by means of computer simulations, scale-model experiments and full-scale trials at sea. The results indicate that a rudder roll stabilization system is able to reduce the roll as well as a conventional fin stabilization system, while it requires less investments. Based on the results obtained in this project the Royal Netherlands Navy has decided to implement rudder roll stabilization on a series of ships under construction at this moment

Control of Towing Kites for Seagoing Vessels

In this paper we present the basic features of the flight control of the SkySails towing kite system. After introduction of coordinate definitions and basic system dynamics we introduce a novel model used for controller design and justify its main dynamics with results from system identification based on numerous sea trials. We then present the controller design which we successfully use for operational flights for several years. Finally we explain the generation of dynamical flight patterns.Comment: 12 pages, 18 figures; submitted to IEEE Trans. on Control Systems Technology; revision: Fig. 15 corrected, minor text change

Application of MPC and sliding mode control to IFAC benchmark models

The comparison of Model Predictive Control (MPC) and Sliding Mode Control (SMC) are presented in this paper. This paper investigates the performance of each controller as the navigation system for IFAC benchmark ship models (cargo vessel and oil tanker). In this investigation the navigation system regulates the heading angle of the two types of marine vessel with reference to a desired heading trajectory. In this investigation, the result obtained from MPC is compared with a well-established control methodology, namely Sliding Mode control theory. Wave disturbances and actuator limits are implemented to provide a more realistic evaluation and comparison for the proposed control structure

Genetic programming for the automatic design of controllers for a surface ship

In this paper, the implementation of genetic programming (GP) to design a contoller structure is assessed. GP is used to evolve control strategies that, given the current and desired state of the propulsion and heading dynamics of a supply ship as inputs, generate the command forces required to maneuver the ship. The controllers created using GP are evaluated through computer simulations and real maneuverability tests in a laboratory water basin facility. The robustness of each controller is analyzed through the simulation of environmental disturbances. In addition, GP runs in the presence of disturbances are carried out so that the different controllers obtained can be compared. The particular vessel used in this paper is a scale model of a supply ship called CyberShip II. The results obtained illustrate the benefits of using GP for the automatic design of propulsion and navigation controllers for surface ships

MODEL REFERENCE ADAPTIVE CONTROL-BASED GENETIC ALGORITHM DESIGN FOR HEADING SHIP MOTION

In this paper, the heading control of a large ship is enhanced with a specific end goal, to check the unwanted impact of the waves on the actuator framework. The Nomoto model is investigated to describe the ship’s guiding progression. First and second order models are considered here. The viability of the models is examined based on the principal properties of the Nomoto model. Different controllers are proposed, these are Proportional Integral Derivative (PID), Linear Quadratic Regulator (LQR) and Model Reference Adaptive Control Genetic optimization Algorithm (MRAC-GA) for a ship heading control. The results show that the MRAC-GA controller provides the best results to satisfy the design requirements. The Matlab/Simulink tool is utilized to demonstrate the proposed arrangement in the control loop

Evolutionary design of a full-envelope full-authority flight control system for an unstable high-performance aircraft

The use of an evolutionary algorithm in the framework of H1 control theory is being considered as a means for synthesizing controller gains that minimize a weighted combination of the infinite norm of the sensitivity function (for disturbance attenuation requirements) and complementary sensitivity function (for robust stability requirements) at the same time. The case study deals with a complete full-authority longitudinal control system for an unstable high-performance jet aircraft featuring (i) a stability and control augmentation system and (ii) autopilot functions (speed and altitude hold). Constraints on closed-loop response are enforced, that representing typical requirements on airplane handling qualities, that makes the control law synthesis process more demanding. Gain scheduling is required, in order to obtain satisfactory performance over the whole flight envelope, so that the synthesis is performed at different reference trim conditions, for several values of the dynamic pressure, used as the scheduling parameter. Nonetheless, the dynamic behaviour of the aircraft may exhibit significant variations when flying at different altitudes, even for the same value of the dynamic pressure, so that a trade-off is required between different feasible controllers synthesized at different altitudes for a given equivalent airspeed. A multiobjective search is thus considered for the determination of the best suited solution to be introduced in the scheduling of the control law. The obtained results are then tested on a longitudinal non-linear model of the aircraft

Ship Course Keeping Using Different Sliding Mode Controllers

This study addresses three sliding mode heading controllers for dealing with uncertain wave disturbances. A nonlinear steering model is derived, and the feedback linearization method is chosen to simplify the nonlinear system in this study. The adaptive method and disturbance observer technique are proposed for course keeping and ensuring robust performance of the time varying wave moment and actuator dynamics. Finally, the simulation results on a navy ship illustrate the effectiveness of the presented control algorithms for course keeping

A Study on the Automatic Ship Control Based on Adaptive Neural Networks

Recently, dynamic models of marine ships are often required to design advanced control systems. In practice, the dynamics of marine ships are highly nonlinear and are affected by highly nonlinear, uncertain external disturbances. This results in parametric and structural uncertainties in the dynamic model, and requires the need for advanced robust control techniques. There are two fundamental control approaches to consider the uncertainty in the dynamic model: robust control and adaptive control. The robust control approach consists of designing a controller with a fixed structure that yields an acceptable performance over the full range of process variations. On the other hand, the adaptive control approach is to design a controller that can adapt itself to the process uncertainties in such a way that adequate control performance is guaranteed. In adaptive control, one of the common assumptions is that the dynamic model is linearly parameterizable with a fixed dynamic structure. Based on this assumption, unknown or slowly varying parameters are found adaptively. However, structural uncertainty is not considered in the existing control techniques. To cope with the nonlinear and uncertain natures of the controlled ships, an adaptive neural network (NN) control technique is developed in this thesis. The developed neural network controller (NNC) is based on the adaptive neural network by adaptive interaction (ANNAI). To enhance the adaptability of the NNC, an algorithm for automatic selection of its parameters at every control cycle is introduced. The proposed ANNAI controller is then modified and applied to some ship control problems. Firstly, an ANNAI-based heading control system for ship is proposed. The performance of the ANNAI-based heading control system in course-keeping and turning control is simulated on a mathematical ship model using computer. For comparison, a NN heading control system using conventional backpropagation (BP) training methods is also designed and simulated in similar situations. The improvements of ANNAI-based heading control system compared to the conventional BP one are discussed. Secondly, an adaptive ANNAI-based track control system for ship is developed by upgrading the proposed ANNAI controller and combining with Line-of-Sight (LOS) guidance algorithm. The off-track distance from ship position to the intended track is included in learning process of the ANNAI controller. This modification results in an adaptive NN track control system which can adapt with the unpredictable change of external disturbances. The performance of the ANNAI-based track control system is then demonstrated by computer simulations under the influence of external disturbances. Thirdly, another application of the ANNAI controller is presented. The ANNAI controller is modified to control ship heading and speed in low-speed maneuvering of ship. Being combined with a proposed berthing guidance algorithm, the ANNAI controller becomes an automatic berthing control system. The computer simulations using model of a container ship are carried out and shows good performance. Lastly, a hybrid neural adaptive controller which is independent of the exact mathematical model of ship is designed for dynamic positioning (DP) control. The ANNAI controllers are used in parallel with a conventional proportional-derivative (PD) controller to adaptively compensate for the environmental effects and minimize positioning as well as tracking error. The control law is simulated on a multi-purpose supply ship. The results are found to be encouraging and show the potential advantages of the neural-control scheme.1. Introduction = 1 1.1 Background and Motivations = 1 1.1.1 The History of Automatic Ship Control = 1 1.1.2 The Intelligent Control Systems = 2 1.2 Objectives and Summaries = 6 1.3 Original Distributions and Major Achievements = 7 1.4 Thesis Organization = 8 2. Adaptive Neural Network by Adaptive Interaction = 9 2.1 Introduction = 9 2.2 Adaptive Neural Network by Adaptive Interaction = 11 2.2.1 Direct Neural Network Control Applications = 11 2.2.2 Description of the ANNAI Controller = 13 2.3 Training Method of the ANNAI Controller = 17 2.3.1 Intensive BP Training = 17 2.3.2 Moderate BP Training = 17 2.3.3 Training Method of the ANNAI Controller = 18 3. ANNAI-based Heading Control System = 21 3.1 Introduction = 21 3.2 Heading Control System = 22 3.3 Simulation Results = 26 3.3.1 Fixed Values of n and = 28 3.3.2 With adaptation of n and r = 33 3.4 Conclusion = 39 4. ANNAI-based Track Control System = 41 4.1 Introduction = 41 4.2 Track Control System = 42 4.3 Simulation Results = 48 4.3.1 Modules for Guidance using MATLAB = 48 4.3.2 M-Maps Toolbox for MATLAB = 49 4.3.3 Ship Model = 50 4.3.4 External Disturbances and Noise = 50 4.3.5 Simulation Results = 51 4.4 Conclusion = 55 5. ANNAI-based Berthing Control System = 57 5.1 Introduction = 57 5.2 Berthing Control System = 58 5.2.1 Control of Ship Heading = 59 5.2.2 Control of Ship Speed = 61 5.2.3 Berthing Guidance Algorithm = 63 5.3 Simulation Results = 66 5.3.1 Simulation Setup = 66 5.3.2 Simulation Results and Discussions = 67 5.4 Conclusion = 79 6. ANNAI-based Dynamic Positioning System = 80 6.1 Introduction = 80 6.2 Dynamic Positioning System = 81 6.2.1 Station-keeping Control = 82 6.2.2 Low-speed Maneuvering Control = 86 6.3 Simulation Results = 88 6.3.1 Station-keeping = 89 6.3.2 Low-speed Maneuvering = 92 6.4 Conclusion = 98 7. Conclusions and Recommendations = 100 7.1 Conclusion = 100 7.1.1 ANNAI Controller = 100 7.1.2 Heading Control System = 101 7.1.3 Track Control System = 101 7.1.4 Berthing Control System = 102 7.1.5 Dynamic Positioning System = 102 7.2 Recommendations for Future Research = 103 References = 104 Appendixes A = 112 Appendixes B = 11