Wind Preview-Based Model Predictive Control of Multi-Rotor UAVs Using LiDAR

Autonomous outdoor operations of Unmanned Aerial Vehicles (UAVs), such as quadrotors, expose the aircraft to wind gusts causing a significant reduction in their position-holding performance. This vulnerability becomes more critical during the automated docking of these vehicles to outdoor charging stations. Utilising real-time wind preview information for the gust rejection control of UAVs has become more feasible due to the advancement of remote wind sensing technology such as LiDAR. This work proposes the use of a wind-preview-based Model Predictive Controller (MPC) to utilise remote wind measurements from a LiDAR for disturbance rejection. Here a ground-based LiDAR unit is used to predict the incoming wind disturbance at the takeoff and landing site of an autonomous quadrotor UAV. This preview information is then utilised by an MPC to provide the optimal compensation over the defined horizon. Simulations were conducted with LiDAR data gathered from field tests to verify the efficacy of the proposed system and to test the robustness of the wind-preview-based control. The results show a favourable improvement in the aircraft response to wind gusts with the addition of wind preview to the MPC; An 80% improvement in its position-holding performance combined with reduced rotational rates and peak rotational angles signifying a less aggressive approach to increased performance when compared with only feedback based MPC disturbance rejection. System robustness tests demonstrated a 1.75 s or 120% margin in the gust preview’s timing or strength respectively before adverse performance impact. The addition of wind-preview to an MPC has been shown to increase the gust rejection of UAVs over standard feedback-based MPC thus enabling their precision landing onto docking stations in the presence of wind gusts

Analysis and Control of a Variable-Pitch Quadrotor for Agile Flight

Fixed-pitch quadrotors are popular research and hobby platforms largely due to their mechanical simplicity relative to other hovering aircraft. This simplicity, however, places fundamental limits on the achievable actuator bandwidth and the possible flight maneuvers. This paper shows that many of these limitations can be overcome by utilizing variable-pitch propellers on a quadrotor. A detailed analysis of the potential benefits of variable-pitch propellers over fixed-pitch propellers for a quadrotor is presented. This analysis is supported with experimental testing to show that variable-pitch propellers, in addition to allowing for generation of reverse thrust, substantially increase the maximum rate of thrust change. A nonlinear, quaternion-based control algorithm for controlling the quadrotor is also presented with an accompanying trajectory generation method that finds polynomial minimum-time paths based on actuator saturation levels. The control law and trajectory generation algorithms are implemented on a custom variable-pitch quadrotor. Several flight tests are shown, which highlight the benefits of a variable-pitch quadrotor over a standard fixed-pitch quadrotor for performing aggressive and aerobatic maneuvers.National Science Foundation (U.S.) (0645960

Design and Demonstration of a Two-Dimentional Test Bed for UAV Controller Evaluation

A three degree-of-freedom (DOF) planar test bed for Unmanned Aerial Vehicle (UAV) controller evaluation was built. The test-bed consists of an instrumented tether and an experimental twin-rotor, planar UAV mounted with a one DOF manipulator mounted below the UAV body. The tether was constructed to constrain the UAV under test to motion on the surface of a sphere. Experiments can be conducted through the tether, approximating motion in a vertical plane by a UAV under test. The tether provides the means to measure the position and attitude of the UAV under test. The experimental twin-rotor UAV and one-link on-board manipulator, were designed and built to explore a unified control strategy for Manipulator on VTOL Aircraft (MOVA), in which the interaction of UAV body dynamics with the manipulator motion is of primary interest. The dynamics of the propulsion unit was characterized through experiments, based on which a phase lead compensator was designed to improve the UAV frequency response. A \u27separate\u27 controller based on independent nonlinear control of the VTOL aircraft and PD linear control of the on-board manipulator was designed as a reference for comparison to the unified MOVA controller. Tests with the separate controller show the negative effect that a coupled manipulator can have on the UAV body motion, while the tests on MOVA show the potential benefit of explicit compensation of the UAV and manipulator interaction