Noise shaping Asynchronous SAR ADC based time to digital converter

Time-to-digital converters (TDCs) are key elements for the digitization of timing information in modern mixed-signal circuits such as digital PLLs, DLLs, ADCs, and on-chip jitter-monitoring circuits. Especially, high-resolution TDCs are increasingly employed in on-chip timing tests, such as jitter and clock skew measurements, as advanced fabrication technologies allow fine on-chip time resolutions. Its main purpose is to quantize the time interval of a pulse signal or the time interval between the rising edges of two clock signals. Similarly to ADCs, the performance of TDCs are also primarily characterized by Resolution, Sampling Rate, FOM, SNDR, Dynamic Range and DNL/INL. This work proposes and demonstrates 2nd order noise shaping Asynchronous SAR ADC based TDC architecture with highest resolution of 0.25 ps among current state of art designs with respect to post-layout simulation results. This circuit is a combination of low power/High Resolution 2nd Order Noise Shaped Asynchronous SAR ADC backend with simple Time to Amplitude converter (TAC) front-end and is implemented in 40nm CMOS technology. Additionally, special emphasis is given on the discussion on various current state of art TDC architectures.Electrical and Computer Engineerin

Fully-passive switched-capacitor techniques for high performance SAR ADC design

In recent years, SAR ADC becomes more and more popular in various low-power applications such as wireless sensors and low energy radios due to its circuit simplicity, high power efficiency, and scaling compatibility. However, its speed is limited by its successive approximation procedures and its power efficiency greatly reduces with the ADC resolution going beyond 10 bit. To address these issues, this thesis proposes to embed two techniques: 1) compressive sensing (CS) and 2) noise shaping (NS) to a conventional SAR ADC. The realization of both techniques are based on fully-passive switched-capacitor techniques. CS is a recently emerging sampling paradigm, stating that the sparsity of a signal can be exploited to reduce the ADC sampling rate below the Nyquist rate. Different from conventional CS frameworks which require dedicated analog CS encoders, this thesis proposes a fully-passive CS-SAR ADC architecture which only requires minor modification to a conventional SAR ADC. Two chips are fabricated in a 0.13 µm process to prove the concept. One chip is a single-channel CS-SAR ADC which can reduce the ADC conversion rate by 4 times, thus reducing the ADC power by 4 times. In many wireless sensing applications, multiple ADCs are commonly required to sense multi-channel signals such as multi-lead ECG sensing and parallel neural recording. Therefore, the other chip is a multi-channel CS-SAR ADC which can simultaneously convert 4-channel signals with a sampling rate of one channel’s Nyquist rate. At 0.8 V and 1 MS/s, both chips achieve an effective Walden FoM of around 5 fJ/conversion-step. This thesis also proposes a novel NS SAR ADC architecture that is simple, robust and low power for high-resolution applications. Compared to conventional ∆Σ ADCs, it replaces the power-hungry active integrator with a passive integrator which only requires one switch and two capacitors. Compared to previous 1st-order NS SAR ADC works, it achieves the best NS performance and can be easily extended to 2nd-order. A 1st-order 10-bit NS SAR ADC is fabricated in a 0.13 µm process. Through NS, SNDR increases by 6 dB with OSR doubled, achieving a 12- bit ENOB at OSR = 8. An improved version of a 2nd-order 9-bit NS SAR ADC is designed and simulated in a 40 nm process. The SNDR increases by 10 dB with OSR doubled, achieving a 14-bit ENOB at OSR = 16. At a bandwidth of 312.5 kHz, the Schreier FoM is 181 dB and the Walden FoM is 12.5 fJ/conversion-step, proving that the proposed NS SAR ADC architecture can achieve high resolution and high power efficiency simultaneously.Electrical and Computer Engineerin

Design of Analog-to-Digital Converters with Embedded Mixing for Ultra-Low-Power Radio Receivers

In the field of radio receivers, down-conversion methods usually rely on one (or more) explicit mixing stage(s) before the analog-to-digital converter (ADC). These stages not only contribute to the overall power consumption but also have an impact on area and can compromise the receiver’s performance in terms of noise and linearity. On the other hand, most ADCs require some sort of reference signal in order to properly digitize an analog input signal. The implementation of this reference signal usually relies on bandgap circuits and reference buffers to generate a constant, stable, dc signal. Disregarding this conventional approach, the work developed in this thesis aims to explore the viability behind the usage of a variable reference signal. Moreover, it demonstrates that not only can an input signal be properly digitized, but also shifted up and down in frequency, effectively embedding the mixing operation in an ADC. As a result, ADCs in receiver chains can perform double-duty as both a quantizer and a mixing stage. The lesser known charge-sharing (CS) topology, within the successive approximation register (SAR) ADCs, is used for a practical implementation, due to its feature of “pre-charging” the reference signal prior to the conversion. Simulation results from an 8-bit CS-SAR ADC designed in a 0.13 μm CMOS technology validate the proposed technique

A jittered-sampling correction technique for ADCs

In Analogue to Digital Converters (ADCs) jittered sampling raises the noise floor; this leads to a decrease in its Signal to Noise ratio (SNR) and its effective number of bits (ENOB). This research studies a technique that compensate for the effects of sampling with a jittered clock. A thorough understanding of sampling in various data converters is complied

High-Bandwidth Voltage-Controlled Oscillator based architectures for Analog-to-Digital Conversion

The purpose of this thesis is the proposal and implementation of data conversion open-loop architectures based on voltage-controlled oscillators (VCOs) built with ring oscillators (RO-based ADCs), suitable for highly digital designs, scalable to the newest complementary metal-oxide-semiconductor (CMOS) nodes. The scaling of the design technologies into the nanometer range imposes the reduction of the supply voltage towards small and power-efficient architectures, leading to lower voltage overhead of the transistors. Additionally, phenomena like a lower intrinsic gain, inherent noise, and parasitic effects (mismatch between devices and PVT variations) make the design of classic structures for ADCs more challenging. In recent years, time-encoded A/D conversion has gained relevant popularity due to the possibility of being implemented with mostly digital structures. Within this trend, VCOs designed with ring oscillator based topologies have emerged as promising candidates for the conception of new digitization techniques. RO-based data converters show excellent scalability and sensitivity, apart from some other desirable properties, such as inherent quantization noise shaping and implicit anti-aliasing filtering. However, their nonlinearity and the limited time delay achievable in a simple NOT gate drastically limits the resolution of the converter, especially if we focus on wide-band A/D conversion. This thesis proposes new ways to alleviate these issues. Firstly, circuit-based techniques to compensate for the nonlinearity of the ring oscillator are proposed and compared to equivalent state-of-the-art solutions. The proposals are designed and simulated in a 65-nm CMOS node for open-loop RO-based ADC architectures. One of the techniques is also validated experimentally through a prototype. Secondly, new ways to artificially increase the effective oscillation frequency are introduced and validated by simulations. Finally, new approaches to shape the quantization noise and filter the output spectrum of a RO-based ADC are proposed theoretically. In particular, a quadrature RO-based band-pass ADC and a power-efficient Nyquist A/D converter are proposed and validated by simulations. All the techniques proposed in this work are especially devoted for highbandwidth applications, such as Internet-of-Things (IoT) nodes or maximally digital radio receivers. Nevertheless, their field of application is not restricted to them, and could be extended to others like biomedical instrumentation or sensing.El propósito de esta tesis doctoral es la propuesta y la implementación de arquitecturas de conversión de datos basadas en osciladores en anillos, compatibles con diseños mayoritariamente digitales, escalables en los procesos CMOS de fabricación más modernos donde las estructuras digitales se ven favorecidas. La miniaturización de las tecnologías CMOS de diseño lleva consigo la reducción de la tensión de alimentación para el desarrollo de arquitecturas pequeñas y eficientes en potencia. Esto reduce significativamente la disponibilidad de tensión para saturar transistores, lo que añadido a una ganancia cada vez menor de los mismos, ruido y efectos parásitos como el “mismatch” y las variaciones de proceso, tensión y temperatura han llevado a que sea cada vez más complejo el diseño de estructuras analógicas eficientes. Durante los últimos años la conversión A/D basada en codificación temporal ha ganado gran popularidad dado que permite la implementación de estructuras mayoritariamente digitales. Como parte de esta evolución, los osciladores controlados por tensión diseñados con topologías de oscilador en anillo han surgido como un candidato prometedor para la concepción de nuevas técnicas de digitalización. Los convertidores de datos basados en osciladores en anillo son extremadamente sensibles (variación de frecuencia con respecto a la señal de entrada) así como escalables, además de otras propiedades muy atractivas, como el conformado espectral de ruido de cuantificación y el filtrado “anti-aliasing”. Sin embargo, su respuesta no lineal y el limitado tiempo de retraso alcanzable por una compuerta NOT restringen la resolución del conversor, especialmente para conversión A/D en aplicaciones de elevado ancho de banda. Esta tesis doctoral propone nuevas técnicas para aliviar este tipo de problemas. En primer lugar, se proponen técnicas basadas en circuito para compensar el efecto de la no linealidad en los osciladores en anillo, y se comparan con soluciones equivalentes ya publicadas. Las propuestas se diseñan y simulan en tecnología CMOS de 65 nm para arquitecturas en lazo abierto. Una de estas técnicas presentadas es también validada experimentalmente a través de un prototipo. En segundo lugar, se introducen y validan por simulación varias formas de incrementar artificialmente la frecuencia de oscilación efectiva. Para finalizar, se proponen teóricamente dos enfoques para configurar nuevas formas de conformación del ruido de cuantificación y filtrado del espectro de salida de los datos digitales. En particular, son propuestos y validados por simulación un ADC pasobanda en cuadratura de fase y un ADC de Nyquist de gran eficiencia en potencia. Todas las técnicas propuestas en este trabajo están destinadas especialmente para aplicaciones de alto ancho de banda, tales como módulos para el Internet de las cosas o receptores de radiofrecuencia mayoritariamente digitales. A pesar de ello, son extrapolables también a otros campos como el de la instrumentación biomédica o el de la medición de señales mediante sensores.Programa de Doctorado en Ingeniería Eléctrica, Electrónica y Automática por la Universidad Carlos III de MadridPresidente: Juan Pablo Alegre Pérez.- Secretario: Celia López Ongil.- Vocal: Fernando Cardes Garcí

Integrated Electronics for Wireless Imaging Microsystems with CMUT Arrays

Integration of transducer arrays with interface electronics in the form of single-chip CMUT-on-CMOS has emerged into the field of medical ultrasound imaging and is transforming this field. It has already been used in several commercial products such as handheld full-body imagers and it is being implemented by commercial and academic groups for Intravascular Ultrasound and Intracardiac Echocardiography. However, large attenuation of ultrasonic waves transmitted through the skull has prevented ultrasound imaging of the brain. This research is a prime step toward implantable wireless microsystems that use ultrasound to image the brain by bypassing the skull. These microsystems offer autonomous scanning (beam steering and focusing) of the brain and transferring data out of the brain for further processing and image reconstruction. The objective of the presented research is to develop building blocks of an integrated electronics architecture for CMUT based wireless ultrasound imaging systems while providing a fundamental study on interfacing CMUT arrays with their associated integrated electronics in terms of electrical power transfer and acoustic reflection which would potentially lead to more efficient and high-performance systems. A fully wireless architecture for ultrasound imaging is demonstrated for the first time. An on-chip programmable transmit (TX) beamformer enables phased array focusing and steering of ultrasound waves in the transmit mode while its on-chip bandpass noise shaping digitizer followed by an ultra-wideband (UWB) uplink transmitter minimizes the effect of path loss on the transmitted image data out of the brain. A single-chip application-specific integrated circuit (ASIC) is de- signed to realize the wireless architecture and interface with array elements, each of which includes a transceiver (TRX) front-end with a high-voltage (HV) pulser, a high-voltage T/R switch, and a low-noise amplifier (LNA). Novel design techniques are implemented in the system to enhance the performance of its building blocks. Apart from imaging capability, the implantable wireless microsystems can include a pressure sensing readout to measure intracranial pressure. To do so, a power-efficient readout for pressure sensing is presented. It uses pseudo-pseudo differential readout topology to cut down the static power consumption of the sensor for further power savings in wireless microsystems. In addition, the effect of matching and electrical termination on CMUT array elements is explored leading to new interface structures to improve bandwidth and sensitivity of CMUT arrays in different operation regions. Comprehensive analysis, modeling, and simulation methodologies are presented for further investigation.Ph.D

Low-pass CMOS Sigma-Delta Converter

A crescente necessidade em dar-se uma melhor saúde à população obriga ao desenvolvimento de novos e melhores dispositivos médicos. Atualmente, uma área de desenvolvimento importante é a de dispositivos portáteis para análise de sinais biológicos, tais como o eletrocardiograma ou o electroencefalograma, ajudando os profissionais de saúde a fazer rápidos diagnósticos no terreno, ou mesmo para serem usados por cidadãos que necessitem de vigilância constante. O desenvolvimento destes aparelhos traz novos desafios para a comunidade cientifica, nomeadamente na interface analógico/digital, na qualidade dos dados obtidos e no gasto energético. Para se conceber um bom dispositivos médico é necessário um conversor analógico/digital para frequências baixas, com baixo consumo energético e elevada resolução. Esta dissertação começa por fornecer ao leitor a teoria básica sobre conversores analógico/digital (ADC) e estado de arte. Como principal objetivo do trabalho desenvolvido, é descrito o desenho de um ADC baseado numa arquitetura Sigma-Delta que vá de encontro aos requisitos mencionados. O conversor foi implementado numa tecnologia 130 nm CMOS, usando uma frequência de amostragem de 1 MHz, com uma largura de banda de 1 kHz e tensão de alimentação 1,2 V. É usada, nos integradores do sigma-delta, uma invulgar tipologia de Opamp de forma a obter um ganho elevado, sem recurso a técnicas cascode. O quantizador possui uma resolução de 1,5 bits e é realizado com dois comparadores dinâmicos, de forma a minimizar o consumo energético.The growing need to provide better health for the population requires the development of new and better medical devices. Portable devices for the analysis of biological signals, such as the electrocardiogram or electroencephalogram, is nowadays an important development, helping health professionals to come up with fast diagnoses on the field, or even for use by citizens who require constant vigilance . Developing these devices brings new challenges to the scientific community, namely at the analog/digital interface, the quality of data and power consumption. In order to design a good medical device it is necessary an analog/digital converter for low frequencies, with low power consumption and high resolution. This dissertation begins by providing the reader with the basic theory of analog/digital (ADC) and its state of the art. The main goal of the work is the design of an ADC based on a Sigma-Delta architecture that meets the necessary medical requirements. The converter was implemented in a 130 nm CMOS technology using a sampling frequency of 1 MHz, with a bandwidth of 1 kHz, and a source voltage of 1.2 V. The integrators of sigma-delta employs an unusual Opamp typology in order to reach a high gain, without resourcing to cascode techniques. The quantizer has a resolution of 1.5 bits and is realized with two dynamic comparators, in order to minimize power consumption

Ultra-low noise, high-frame rate readout design for a 3D-stacked CMOS image sensor

Due to the switch from CCD to CMOS technology, CMOS based image sensors have become smaller, cheaper, faster, and have recently outclassed CCDs in terms of image quality. Apart from the extensive set of applications requiring image sensors, the next technological breakthrough in imaging would be to consolidate and completely shift the conventional CMOS image sensor technology to the 3D-stacked technology. Stacking is recent and an innovative technology in the imaging field, allowing multiple silicon tiers with different functions to be stacked on top of each other. The technology allows for an extreme parallelism of the pixel readout circuitry. Furthermore, the readout is placed underneath the pixel array on a 3D-stacked image sensor, and the parallelism of the readout can remain constant at any spatial resolution of the sensors, allowing extreme low noise and a high-frame rate (design) at virtually any sensor array resolution. The objective of this work is the design of ultra-low noise readout circuits meant for 3D-stacked image sensors, structured with parallel readout circuitries. The readout circuit’s key requirements are low noise, speed, low-area (for higher parallelism), and low power. A CMOS imaging review is presented through a short historical background, followed by the description of the motivation, the research goals, and the work contributions. The fundamentals of CMOS image sensors are addressed, as a part of highlighting the typical image sensor features, the essential building blocks, types of operation, as well as their physical characteristics and their evaluation metrics. Following up on this, the document pays attention to the readout circuit’s noise theory and the column converters theory, to identify possible pitfalls to obtain sub-electron noise imagers. Lastly, the fabricated test CIS device performances are reported along with conjectures and conclusions, ending this thesis with the 3D-stacked subject issues and the future work. A part of the developed research work is located in the Appendices.Devido à mudança da tecnologia CCD para CMOS, os sensores de imagem em CMOS tornam se mais pequenos, mais baratos, mais rápidos, e mais recentemente, ultrapassaram os sensores CCD no que respeita à qualidade de imagem. Para além do vasto conjunto de aplicações que requerem sensores de imagem, o próximo salto tecnológico no ramo dos sensores de imagem é o de mudar completamente da tecnologia de sensores de imagem CMOS convencional para a tecnologia “3D-stacked”. O empilhamento de chips é relativamente recente e é uma tecnologia inovadora no campo dos sensores de imagem, permitindo vários planos de silício com diferentes funções poderem ser empilhados uns sobre os outros. Esta tecnologia permite portanto, um paralelismo extremo na leitura dos sinais vindos da matriz de píxeis. Além disso, num sensor de imagem de planos de silício empilhados, os circuitos de leitura estão posicionados debaixo da matriz de píxeis, sendo que dessa forma, o paralelismo pode manter-se constante para qualquer resolução espacial, permitindo assim atingir um extremo baixo ruído e um alto debito de imagens, virtualmente para qualquer resolução desejada. O objetivo deste trabalho é o de desenhar circuitos de leitura de coluna de muito baixo ruído, planeados para serem empregues em sensores de imagem “3D-stacked” com estruturas altamente paralelizadas. Os requisitos chave para os circuitos de leitura são de baixo ruído, rapidez e pouca área utilizada, de forma a obter-se o melhor rácio. Uma breve revisão histórica dos sensores de imagem CMOS é apresentada, seguida da motivação, dos objetivos e das contribuições feitas. Os fundamentos dos sensores de imagem CMOS são também abordados para expor as suas características, os blocos essenciais, os tipos de operação, assim como as suas características físicas e suas métricas de avaliação. No seguimento disto, especial atenção é dada à teoria subjacente ao ruído inerente dos circuitos de leitura e dos conversores de coluna, servindo para identificar os possíveis aspetos que dificultem atingir a tão desejada performance de muito baixo ruído. Por fim, os resultados experimentais do sensor desenvolvido são apresentados junto com possíveis conjeturas e respetivas conclusões, terminando o documento com o assunto de empilhamento vertical de camadas de silício, junto com o possível trabalho futuro

Power Efficient Architectures for Low Noise Switched-Capacitor Filters and High Accuracy Analog-to-Digital Converters

Filters and data converters are key analog-and-mixed-signal (AMS) building blocks in communication systems, such as software-defined radios and internet-of-things. In this dissertation, novel switched-capacitor filter and analog-to-digital converter (ADC) circuit configurations have been explored which are power efficient and are digital scaling friendly. First, a novel switched-capacitor low-pass filter architecture is presented. In the proposed scheme, a feedback path is added to a charge-rotating real-pole filter to implement complex poles. The selectivity is enhanced, and the in-band loss is reduced compared with the real-pole filter. The output thermal noise level and the tuning range are both close to those of the real-pole filter. A fourth-order filter prototype was implemented in a 180-nm CMOS technology. The measured in-band loss is reduced by 3.3 dB compared with that of a real-pole filter. The sampling rate of the filter is programmable from 65 to 300 MS/s with a constant DC gain. The 3-dB cut-off frequency of the filter can be tuned from 0.490 to 13.3 MHz with over 100-dB maximum stop-band rejection. The measured in-band third-order output intercept point is 28.7 dBm, and the averaged spot noise is 6.54 nV/Hz. The filter consumes 4.3 mW from a 1.8 V supply. Next, an opamp-free noise shaping successive-approximation register (SAR) ADC is presented. Third-order noise shaping is achieved by implementing a second-order passive filter and a passive error feedback topology. In the proposed scheme, the SAR error signals (including quantization noise, comparator thermal noise, and DAC settling error) are subjected to third-order noise shaping. Therefore, the thermal noise specifications of the comparator can be relaxed. Also, since no active element is used, the proposed scheme achieves a higher power efficiency than earlier SAR ADCs. Finally, a novel 0-2 Multi Stage Noise Shaping (MASH) ADC is presented. The first stage is implemented using a 4-bit SAR ADC. The second stage uses a VCO-based quantizer (VCOQ). Unlike earlier VCOQs which provide first-order noise shaping, the proposed VCOQ achieves second-order noise filtering. To implement this noise shaping, the quantization noise of the VCOQ is extracted as a pulse-width-modulated (PWM) signal, and it is fed back to the VCO input using a charge pump circuit. Any error related to the charge pump circuitry will be first-order shaped at the output. Simulation results confirm the second-order noise shaping of the output of the ADC, and an excellent (14-bit SNDR) performance with oversampling ratio (OSR) of 16