New Passive Instruments Developed for Ocean Monitoring at the Remote Sensing Lab—Universitat Politècnica de Catalunya

Lack of frequent and global observations from space is currently a limiting factor in many Earth Observation (EO) missions. Two potential techniques that have been proposed nowadays are: (1) the use of satellite constellations, and (2) the use of Global Navigation Satellite Signals (GNSS) as signals of opportunity (no transmitter required). Reflectometry using GNSS opportunity signals (GNSS-R) was originally proposed in 1993 by Martin-Neira (ESA-ESTEC) for altimetry applications, but later its use for wind speed determination has been proposed, and more recently to perform the sea state correction required in sea surface salinity retrievals by means of L-band microwave radiometry (TB). At present, two EO space-borne missions are currently planned to be launched in the near future: (1) ESA's SMOS mission, using a Y-shaped synthetic aperture radiometer, launch date November 2nd, 2009, and (2) NASA-CONAE AQUARIUS/SAC-D mission, using a three beam push-broom radiometer. In the SMOS mission, the multi-angle observation capabilities allow to simultaneously retrieve not only the surface salinity, but also the surface temperature and an “effective” wind speed that minimizes the differences between observations and models. In AQUARIUS, an L-band scatterometer measuring the radar backscatter (σ0) will be used to perform the necessary sea state corrections. However, none of these approaches are fully satisfactory, since the effective wind speed captures some sea surface roughness effects, at the expense of introducing another variable to be retrieved, and on the other hand the plots (TB-σ0) present a large scattering. In 2003, the Passive Advance Unit for ocean monitoring (PAU) project was proposed to the European Science Foundation in the frame of the EUropean Young Investigator Awards (EURYI) to test the feasibility of GNSS-R over the sea surface to make sea state measurements and perform the correction of the L-band brightness temperature. This paper: (1) provides an overview of the Physics of the L-band radiometric and GNSS reflectometric observations over the ocean, (2) describes the instrumentation that has been (is being) developed in the frame of the EURYI-funded PAU project, (3) the ground-based measurements carried out so far, and their interpretation in view of placing a GNSS-reflectometer as secondary payload in future SMOS follow-on missions

El uso de señales de oportunidad GPS para observación de la Tierra

Peer Reviewe

De campañas de medidas a productos de salinidad: un tributo a las contribuciones de Jordi Font a la mision SMOS

Camps, Adriano ... et al.-- Special volume: Planet Ocean. Scientia Marina 80(Suppl.1) 2016.-- 14 pages, 20 figures[EN] This article summarizes some of the activities in which Jordi Font, research professor and head of the Department of Physical and Technological Oceanography, Institut de Ciències del Mar (CSIC, Spanish National Research Council) in Barcelona, has been involved as co-Principal Investigator for Ocean Salinity of the European Space Agency Soil Moisture and Ocean Salinity (SMOS) Earth Explorer Mission from the perspective of the Remote Sensing Lab at the Universitat Politècnica de Catalunya. We have probably left out some of his many contributions to salinity remote sensing, but we hope that this review will give an idea of the importance of his work. We focus on the following issues: 1) the new accurate measurements of the sea water dielectric constant, 2) the WISE and EuroSTARRS field experiments that helped to define the geophysical model function relating brightness temperature to sea state, 3) the FROG 2003 field experiment that helped to understand the emission of sea foam, 4) GNSS-R techniques for improving sea surface salinity retrieval, 5) instrument characterization campaigns, and 6) the operational implementation of the Processing Centre of Levels 3 and 4 at the SMOS Barcelona Expert Centre[ES] Este artículo resume algunas de las actividades en las que Jordi Font, profesor de investigación y jefe del Departamento de Física y Tecnología Oceanográfica, del Institut de Ciències del Mar (CSIC) en Barcelona, ha estado desarrollando como co-Investigador Principal de la parte de la misión SMOS de la ESA, una misión Earth Explorer, desde la perspectiva del Remote Sensing Lab, de la Universitat Politècnica de Catalunya. Seguramente, estamos olvidando algunas de sus muchas contribuciones a la teledetección de la salinidad, pero esperamos que esta revisión dé una idea de la importancia de su trabajo. Este artículo se focaliza en los siguientes puntos: 1) las medidas de alta calidad de la constante dieléctrica del agua marina, 2) las campañas de medidas WISE y EuroSTARRS que ayudaron a la definición del modelo geofísico relacionando la temperatura de brillo con el estado del mar, 3) la campaña de medidas FROG 2003 que ayudó a entender la emisión de la espuma marina 4) presentación de las técnicas de GNSS-R para la mejora de la recuperación de la salinidad superficial 5) campañas para la caracterización del instrumento y 6) la implantación del centro de procesado operacional de niveles 3 y 4 en el SMOS Barcelona Expert CentreThis work has been performed under research grants TEC2005-06863-C02-01/TCM, ESP2005-06823-C05 and ESP2007-65667-C04, AYA2008-05906-C02-01/ESP, AYA2010-22062-C05 and ESP2015-70014-C2-1-R, and EURYI 2004 awardPeer Reviewe

De campañas de medidas a productos de salinidad: un tributo a las contribuciones de Jordi Font a la mision SMOS

This article summarizes some of the activities in which Jordi Font, research professor and head of the Department of Physical and Technological Oceanography, Institut de Ciències del Mar (CSIC, Spanish National Research Council) in Barcelona, has been involved as co-Principal Investigator for Ocean Salinity of the European Space Agency Soil Moisture and Ocean Salinity (SMOS) Earth Explorer Mission from the perspective of the Remote Sensing Lab at the Universitat Politècnica de Catalunya. We have probably left out some of his many contributions to salinity remote sensing, but we hope that this review will give an idea of the importance of his work. We focus on the following issues: 1) the new accurate measurements of the sea water dielectric constant, 2) the WISE and EuroSTARRS field experiments that helped to define the geophysical model function relating brightness temperature to sea state, 3) the FROG 2003 field experiment that helped to understand the emission of sea foam, 4) GNSS-R techniques for improving sea surface salinity retrieval, 5) instrument characterization campaigns, and 6) the operational implementation of the Processing Centre of Levels 3 and 4 at the SMOS Barcelona Expert Centre.Este artículo resume algunas de las actividades en las que Jordi Font, profesor de investigación y jefe del Departamento de Física y Tecnología Oceanográfica, del Institut de Ciències del Mar (CSIC) en Barcelona, ha estado desarrollando como co-Investigador Principal de la parte de la misión SMOS de la ESA, una misión Earth Explorer, desde la perspectiva del Remote Sensing Lab, de la Universitat Politècnica de Catalunya. Seguramente, estamos olvidando algunas de sus muchas contribuciones a la teledetección de la salinidad, pero esperamos que esta revisión dé una idea de la importancia de su trabajo. Este artículo se focaliza en los siguientes puntos: 1) las medidas de alta calidad de la constante dieléctrica del agua marina, 2) las campañas de medidas WISE y EuroSTARRS que ayudaron a la definición del modelo geofísico relacionando la temperatura de brillo con el estado del mar, 3) la campaña de medidas FROG 2003 que ayudó a entender la emisión de la espuma marina 4) presentación de las técnicas de GNSS-R para la mejora de la recuperación de la salinidad superficial 5) campañas para la caracterización del instrumento y 6) la implantación del centro de procesado operacional de niveles 3 y 4 en el SMOS Barcelona Expert Centre

Selection of the key earth observation sensors and platforms focusing on applications for Polar Regions in the scope of Copernicus system 2020-2030

An optimal payload selection conducted in the frame of the H2020 ONION project (id 687490) is presented based on the ability to cover the observation needs of the Copernicus system in the time period 2020–2030. Payload selection is constrained by the variables that can be measured, the power consumption, and weight of the instrument, and the required accuracy and spatial resolution (horizontal or vertical). It involved 20 measurements with observation gaps according to the user requirements that were detected in the top 10 use cases in the scope of Copernicus space infrastructure, 9 potential applied technologies, and 39 available commercial platforms. Additional Earth Observation (EO) infrastructures are proposed to reduce measurements gaps, based on a weighting system that assigned high relevance for measurements associated to Marine for Weather Forecast over Polar Regions. This study concludes with a rank and mapping of the potential technologies and the suitable commercial platforms to cover most of the requirements of the top ten use cases, analyzing the Marine for Weather Forecast, Sea Ice Monitoring, Fishing Pressure, and Agriculture and Forestry: Hydric stress as the priority use cases.Peer ReviewedPostprint (published version

Contributions to the design of energy harvesting systems for autonomous sensors in low power marine applications

Tesi en modalitat de compendi de publicacionsOceanographic sensor platforms provide biological and meteorological data to help understand changes in marine environment and help to preserve it. Lagrangian drifters are autonomous passive floating platforms used in climate research to obtain surface marine data. They are low-cost, versatile, easy-to-deploy and can cover large extensions of the ocean when deployed in group. These deployments can last for years, so one of the main design challenges is the autonomy of the drifter. Several energy harvesting (EH) sources are being explored to reduce costs in battery replacement maintenance efforts such as solar panels. Drifters must avoid the impact of the wind because this may compromise proper surface current tracking and therefore, should ideally be mostly submerged. This interferes with the feasibility of solar harvesting, so other EH sources are being explored such as the oscillatory movement of the drifter caused by ocean waves. Wave energy converters (WEC) are the devices that turn this movement into energy. The motion of the drifter can principally be described by 3 oscillatory degrees of freedom (DoF); surge, heave and pitch. The heave motion includes the buoyancy’s response of the drifter, which can be explained by a mass-spring-damping model. By including the wave’s hydrodynamic load in this model, it is converted into a nonlinear system whose frequency response includes the wave’s frequency and the natural frequencies from the linear system. A smart option to maximize the captured energy is to design the inner WEC with a natural frequency similar to that of the drifter's movement. In this thesis, a 4 DoF model is obtained. This model includes the heave, the surge and the pitch motion of the drifter in addition to the inner pendulum motion relative to the buoy. Simultaneously, different pendulum-type WECs for small-size oceanic drifters are proposed. One of these converters consists of an articulated double-pendulum arm with a proof mass that generates energy through its relative motion with the buoy. Different experimental tests are carried out, with a prototype below 10 cm in diameter and 300 g of total mass, proving the capability of harvesting hundreds of microwatts in standard sea conditions EH sources require an additional power management unit (PMU) to convert their variable output into a constant and clean source to be able to feed the sensor electronics. PMUs should also ensure that the maximum available energy is harvested with a maximum power point tracking (MPPT) algorithm. Some sources, such as WECs, require fast MPPT as its output can show relatively rapid variations. However, increasing the sampling rate may reduce the harvested energy. In this thesis, this trade-off is analyzed using the resistor-based fractional open circuit voltage-MPPT technique, which is appropriate for low-power EH sources. Several experiments carried out in marine environments demonstrate the need for increasing the sampling rate. For this purpose, the use of a commercial PMU IC with additional low-power circuitry is proposed. Three novel circuits with a sampling period of 60 ms are manufactured and experimentally evaluated with a small-scale and low-power WEC. Results show that these configurations improve the harvested energy by 26% in comparison to slow sampling rate configurations. Finally, an EH-powered oceanographic monitoring system with a custom wave measuring algorithm is designed. By using the energy collected by a small-size WEC, this system is capable of transmitting up to 22 messages per day containing data on its location and measured wave parameters.Les plataformes d’observació oceanogràfiques integren sensors que proporcionen dades físiques i biogeoquímiques de l’oceà que ajuden a entendre canvis en l’entorn marí. Un exemple d’aquestes plataformes són les boies de deriva (drifters), que són dispositius autònoms i passius utilitzats en l’àmbit de la recerca climàtica per obtenir dades in-situ de la superfície marina. Aquests instruments són de baix cost, versàtils, fàcils de desplegar i poden cobrir grans superfícies quan s’utilitzen en grup. L’autonomia és un dels principals desafiaments en el disseny de drifters. Per tal d’evitar els costos en la substitució de bateries, s’estudien diferents fonts de captació d’energia com per exemple la solar. Els drifters utilitzats per l’estudi dels corrents marins superficials han d’evitar l’impacte directe del vent ja que afecta al correcte seguiment de les corrents i, per tant, cal que estiguin majoritàriament submergides. Això compromet la viabilitat de l’energia solar, fet que requereix l’estudi d’altres fonts de captació com el propi moviment de la boia causat per les onades. Els convertidors d’energia de les onades (WEC, wave energy converters) compleixen aquesta funció. El moviment dels drifters pot explicar-se bàsicament a través de 3 graus de llibertat oscil·latoris: la translació vertical i la horitzontal i el balanceig. La translació vertical inclou la flotabilitat del dispositiu, que es pot descriure mitjançant el model massamolla- amortidor. Incloure la càrrega hidrodinàmica de l’onada en aquest model el converteix en un sistema no lineal amb una resposta freqüencial que inclou la de l’onada i les naturals del sistema lineal. Una opció per maximitzar l’energia captada és dissenyar el WEC amb una freqüència natural similar a la del moviment de la boia. En aquesta tesis es proposa un model de 4 graus de llibertat per a l’estudi del moviment del drifter. Aquest inclou els 3 graus de llibertat de la boia i el moviment del pèndul relatiu a ella. En paral·lel, es proposen diferents WEC del tipus pendular per drifters de reduïdes dimensions. Un d’aquests WEC consisteix en un doble braç articulat amb massa flotant que genera energia a través del seu moviment relatiu al drifter. S’han dut a terme diferents proves experimentals amb un prototip inferior a 10 cm de diàmetre i 300 g de massa, les quals demostren la seva capacitat de captar centenars de microwatts en condicions marines estàndard. Utilitzar fonts de captació d’energia requereix incloure una unitat gestora de potència (PMU, power management unit) per tal de convertir la seva sortida variable en una font constant i neta que alimenti l’electrònica dels sensors. Les PMU també tenen la funció d’assegurar que es recull la màxima energia mitjançant un algoritme de seguiment del punt de màxima potència. Els WEC requereixen un seguiment d’aquest punt ràpid perquè la seva sortida consta de variacions relativament ràpides. Tanmateix, augmentar la freqüència de mostreig pot reduir l’energia captada. En aquesta tesi, s'analitza a fons aquesta relació utilitzant la tècnica de seguiment de la tensió en circuit obert fraccionada basada en resistències, que és molt adequada per a fonts de baixa potència. Diversos experiments realitzats en el medi marí mostren la necessitat d'augmentar la freqüència de mostreig, així que es proposa l'ús de PMU comercials amb una electrònica addicional de baix consum. S’han fabricat tres circuits diferents amb un període de mostreig de 60 ms i s’han avaluat experimentalment en un WEC de reduïdes dimensions. Els resultats mostren que aquestes configuracions milloren l'energia recollida en un 26% en comparació a PMU amb mostreig més lent. Finalment, s’ha dissenyat un sistema autònom de monitorització marina que inclou un algoritme de mesura d'ones propi. Aquest sistema és capaç de transmetre fins a 22 missatges al diaPostprint (published version

Contributions to GNSS-R earth remote sensing from nano-satellites

Premi extraordinari doctorat UPC curs 2015-2016, àmbit de CiènciesGlobal Navigation Satellite Systems Reflectometry (GNSS-R) is a multi-static radar using navigation signals as signals of opportunity. It provides wide-swath and improved spatio-temporal sampling over current space-borne missions. The lack of experimental datasets from space covering signals from multiple constellations (GPS, GLONASS, Galileo, Beidou) at dual-band (L1 and L2) and dual-polarization (Right Hand Left Hand Circular Polarization: RHCP and LHCP), over the ocean, land and cryosphere remains a bottleneck to further develop these techniques. 3Cat-2 is a 6 units (3 x 2 elementary blocks of 10 x 10 x 10 cm3) CubeSat mission ayming to explore fundamentals issues towards an improvement in the understanding of the bistatic scattering properties of different targets. Since geolocalization of specific reflections points is determined by the geometry only, a moderate pointing accuracy is still required to correct for the antena pattern in scatterometry measurements. 3Cat-2 launch is foreseen for the first quarter 2016 into a Sun-Synchronous orbit of 510 km height using a Long March II D rocket. This Ph.D. Thesis represents the main contributions to the development of the 3Cat-2 GNSS-R Earth observation mission (6U CubeSat) including a novel type of GNSS-R technique: the reconstructed one. The desing, development of the platform, and a number of ground-based, airborne and stratospheric balloon experiments to validate the technique and to optimize the instrument. In particular, the main contributions of this Ph.D. thesis are: 1) A novel dual-band Global Navigation Satellite Systems Reflectometer that uses the P(Y) and C/A signals scattered over the sea surface to perform highly precise altimetric measurements (PYCARO). 2) The first proof-of-concept of PYCARO was performed during two different ground-based field experiments over a dam and over the sea under different surface roughness conditions. 3) The scattering of GNSS signals over a water surface has been studied when the receiver is at low height, as for GNSS-R coastal altimetry applications. The precise determination of the local sea level and wave state from the coast can provide useful altimetry and wave information as "dry" tide and wave gauges. In order to test this concept an experiment has been conducted at the Canal d'Investigació i Experimentació Marítima (CIEM) wave channel for two synthetic "sea" states. 4) Two ESA-sponsored airborne experiments were perfomed to test the precision and the relative accuracy of the conventional GNSS-R. 5) The empirical results of a GNSS-R experiment on-board the ESA-sponsored BAXUS 17 stratospheric balloon campaign performed North of Sweden over boreal forests showed that the power of the reflected signals is nearly independent of the platform height for a high coherent integration time. 6) An improved version of the PYCARO payload was tested in Octover 2014 for the second time during the ESA-sposored BEXUS-19,. This work achieved the first ever dual-frequency, multi-constellation GNSS-R observations over boreal forests and lakes using GPS, GLONASS and Galileo signals. 7) The first-ever dual-frequency multi-constellation GNSS-R dual-polarization measurements over boreal forests and lakes were obtained from the stratosphere during the BEXUS 19 using the PYCARO reflectometer operated in closed-loop mode.Global Navigation Satellite Systems Reflectometry (GNSS-R) es una técnica de radar multi-estático que usa señales de radio-navegación como señales de oportunidad. Esta técnica proporciona "wide-swath" y un mejor sampleado espacio-temporal en comparación con las misiones espaciales actuales. La falta de datos desde el espacio proporcionando señales de múltiples constelaciones (GPS, GLONASS, Galileo, Beidou) en doble banda (L1 y L2) y en doble polarización (RHCP y LHCP) sobre océano, tierra y criosfera continua siendo un problema por solucionar. 3Cat-2 es un cubesat de 6 unidades con el objetivo de explorar elementos fundamentales para mejorar el conocimiento sobre el scattering bi-estático sobre diferentes medios dispersores. Dado que la geolocalización de puntos de reflexión específicos está determinada solo por geometría, es necesario un requisito moderado de apuntamiento para corregir el diagrama de antena en aplicaciones de dispersometría. El lanzamiento del 3Cat-2 será en Q2 2016 en una órbitra heliosíncrona usando un cohete Long March II D. Esta tesis representa las contribuciones principales al desarrollo del satélite 3Cat2 para realizar observación de la tierra con GNSS-R incluyendo una nueva técnica: "the reconstructed-code GNSS-R". El diseño, desarrollo de la plataforma y un número de experimentos en tierra, desde avión y desde globo estratosférico para validar la técnica y optimizar el instrumento han sido realizados. En particular, las contribuciones de esta Ph.D. son: 1) un novedoso Global Navigation Satellite Systems Reflectometer que usa las señales P(Y) y C/A después de ser dispersadas sobre la superficie del mar para realizar medidas altimétricas muy precisas. (PYCARO). 2) La primera prueba de concepto de PYCARO se hizo en dos experimentos sobre un pantano y sobre el mar bajo diferentes condiciones de rugosidad. 3) La disperión de las señales GNSS sobre una superfice de agua ha sido estudiada para bajas altitudes para aplicaciones GNSS-R altimétricas de costa. La determinación precisa del nivel local del mar y el estado de las olas desde la costa puede proporcionar información útil de altimetría e información de olas. Para hacer un test de este concepto un experimento en el Canal d'Investigació i Experimentació Marítima (CIEM) fue realizado para dos estados sintéticos de rugosidad. 4) Dos experimentos en avión con esponsor de la ESA se realizaron para estudiar la preción y la exactitud relativa de cGNSS-R. 5) Los resultados empíricos del experimento GNSS-R en BEXUS 17 con esponsor de la ESA realizado en el norte de Suecia sobre bosques boreales mostró que la potencia reflejada de las señales es independiente de la altitud de la plataforma para un tiempo de integración coherente muy alto. 6) Una versión mejorada del PYCARO fue testeada en octubre del 2014 por segunda vez durante el BEXUS 19 que también fue patrocidado por la ESA. Este trabajo proporcionó las primeras medidas GNSS-R sobre bosques boreales en doble frecuencia usando varias constelaciones GNSS. 7) Las primeras medidas polarimétricas (RHCP y LHCP) de GNSS-R sobre bosques boreales también fueron conseguidas durante el experimento BEXUS 19.Award-winningPostprint (published version

Experimental validation and modeling of plucked piezoelectric for underwater energy harvesting system

Underwater wireless sensing systems are envisioned for stand-alone applications and as an addition to cabled observatory systems such as the OBSEA marine observatory. Therefore, this work presents a solution on how to generate power for marine wireless sensors using underwater motion energy. In this pare it is described a prototype based on a Bristol cylinder which can generate electrical voltage using piezoelectric bimorphs. Collecting water motion energy using piezoelectric energy harvesting is particularly difficult due to the mismatch between the low frequency of water kinetics and the high-frequency requirements of piezoelectric transducers. Therefore, to achieve frequency up-conversion we propose the use of the plucking technique applied to propose the use of the plucking technique applied to piezoelectric energy harvester. Experimental results show that the proposed energy harvester achieves a maximum power density of 350µW/cm3.Peer ReviewedPostprint (published version