5G Radio Access Network Architecture for Terrestrial Broadcast Services

The 3rd Generation Partnership Project (3GPP) has defined based on the Long Term Evolution (LTE) enhanced Multicast Broadcast Multimedia Service (eMBMS) a set of new features to support the distribution of Terrestrial Broadcast services in Release 14. On the other hand, a new 5th Generation (5G) system architecture and radio access technology, 5G New Radio (NR), are being standardised from Release 15 onwards, which so far have only focused on unicast connectivity. This may change in Release 17 given a new Work Item set to specify basic Radio Access Network (RAN) functionalities for the provision of multicast/broadcast communications for NR. This work initially excludes some of the functionalities originally supported for Terrestrial Broadcast services under LTE e.g. free to air, receive-only mode, large-area single frequency networks, etc. This paper proposes an enhanced Next Generation RAN architecture based on 3GPP Release 15 with a series of architectural and functional enhancements, to support an efficient, flexible and dynamic selection between unicast and multicast/broadcast transmission modes and also the delivery of Terrestrial Broadcast services. The paper elaborates on the Cloud-RAN based architecture and proposes new concepts such as the RAN Broadcast/Multicast Areas that allows a more flexible deployment in comparison to eMBMS. High-level assessment methodologies including complexity analysis and inspection are used to evaluate the feasibility of the proposed architecture design and compare it with the 3GPP architectural requirements.Comment: 12 pages, 10 figures, 2 tables, IEEE Trans. Broadcastin

MBMS—IP Multicast/Broadcast in 3G Networks

In this article, the Multimedia Broadcast and Multicast Service (MBMS) as standardized in 3GPP is presented. With MBMS, multicast and broadcast capabilities are introduced into cellular networks. After an introduction into MBMS technology, MBMS radio bearer realizations are presented. Different MBMS bearer services like broadcast mode, enhanced broadcast mode and multicast mode are discussed. Streaming and download services over MBMS are presented and supported media codecs are listed. Service layer components as defined in Open Mobile Alliance (OMA) are introduced. For a Mobile TV use case capacity improvements achieved by MBMS are shown. Finally, evolution of MBMS as part of 3GPP standardization is presented

Interoperability of wireless communication technologies in hybrid networks: Evaluation of end-to-end interoperability issues and quality of service requirements

This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.Hybrid Networks employing wireless communication technologies have nowadays brought closer the vision of communication “anywhere, any time with anyone”. Such communication technologies consist of various standards, protocols, architectures, characteristics, models, devices, modulation and coding techniques. All these different technologies naturally may share some common characteristics, but there are also many important differences. New advances in these technologies are emerging very rapidly, with the advent of new models, characteristics, protocols and architectures. This rapid evolution imposes many challenges and issues to be addressed, and of particular importance are the interoperability issues of the following wireless technologies: Wireless Fidelity (Wi-Fi) IEEE802.11, Worldwide Interoperability for Microwave Access (WiMAX) IEEE 802.16, Single Channel per Carrier (SCPC), Digital Video Broadcasting of Satellite (DVB-S/DVB-S2), and Digital Video Broadcasting Return Channel through Satellite (DVB-RCS). Due to the differences amongst wireless technologies, these technologies do not generally interoperate easily with each other because of various interoperability and Quality of Service (QoS) issues. The aim of this study is to assess and investigate end-to-end interoperability issues and QoS requirements, such as bandwidth, delays, jitter, latency, packet loss, throughput, TCP performance, UDP performance, unicast and multicast services and availability, on hybrid wireless communication networks (employing both satellite broadband and terrestrial wireless technologies). The thesis provides an introduction to wireless communication technologies followed by a review of previous research studies on Hybrid Networks (both satellite and terrestrial wireless technologies, particularly Wi-Fi, WiMAX, DVB-RCS, and SCPC). Previous studies have discussed Wi-Fi, WiMAX, DVB-RCS, SCPC and 3G technologies and their standards as well as their properties and characteristics, such as operating frequency, bandwidth, data rate, basic configuration, coverage, power, interference, social issues, security problems, physical and MAC layer design and development issues. Although some previous studies provide valuable contributions to this area of research, they are limited to link layer characteristics, TCP performance, delay, bandwidth, capacity, data rate, and throughput. None of the studies cover all aspects of end-to-end interoperability issues and QoS requirements; such as bandwidth, delay, jitter, latency, packet loss, link performance, TCP and UDP performance, unicast and multicast performance, at end-to-end level, on Hybrid wireless networks. Interoperability issues are discussed in detail and a comparison of the different technologies and protocols was done using appropriate testing tools, assessing various performance measures including: bandwidth, delay, jitter, latency, packet loss, throughput and availability testing. The standards, protocol suite/ models and architectures for Wi-Fi, WiMAX, DVB-RCS, SCPC, alongside with different platforms and applications, are discussed and compared. Using a robust approach, which includes a new testing methodology and a generic test plan, the testing was conducted using various realistic test scenarios on real networks, comprising variable numbers and types of nodes. The data, traces, packets, and files were captured from various live scenarios and sites. The test results were analysed in order to measure and compare the characteristics of wireless technologies, devices, protocols and applications. The motivation of this research is to study all the end-to-end interoperability issues and Quality of Service requirements for rapidly growing Hybrid Networks in a comprehensive and systematic way. The significance of this research is that it is based on a comprehensive and systematic investigation of issues and facts, instead of hypothetical ideas/scenarios or simulations, which informed the design of a test methodology for empirical data gathering by real network testing, suitable for the measurement of hybrid network single-link or end-to-end issues using proven test tools. This systematic investigation of the issues encompasses an extensive series of tests measuring delay, jitter, packet loss, bandwidth, throughput, availability, performance of audio and video session, multicast and unicast performance, and stress testing. This testing covers most common test scenarios in hybrid networks and gives recommendations in achieving good end-to-end interoperability and QoS in hybrid networks. Contributions of study include the identification of gaps in the research, a description of interoperability issues, a comparison of most common test tools, the development of a generic test plan, a new testing process and methodology, analysis and network design recommendations for end-to-end interoperability issues and QoS requirements. This covers the complete cycle of this research. It is found that UDP is more suitable for hybrid wireless network as compared to TCP, particularly for the demanding applications considered, since TCP presents significant problems for multimedia and live traffic which requires strict QoS requirements on delay, jitter, packet loss and bandwidth. The main bottleneck for satellite communication is the delay of approximately 600 to 680 ms due to the long distance factor (and the finite speed of light) when communicating over geostationary satellites. The delay and packet loss can be controlled using various methods, such as traffic classification, traffic prioritization, congestion control, buffer management, using delay compensator, protocol compensator, developing automatic request technique, flow scheduling, and bandwidth allocation

Point-to-Multipoint Services on Fifth-Generation Mobile Networks

[ES] Esta disertación cubre el estado del arte en LTE eMBMS Release 14, también conocido como Enhanced Television Services (ENTV). ENTV trajo un conjunto de mejoras, tanto a nivel radio como a nivel de núcleo, que transformó a eMBMS en un estándar de televisión terrestre completo. La última versión de esta tecnología se denomina LTE-based 5G Broadcast; pero no usa New Radio ni el núcleo 5G. Para proveer una solución nativa 5G de servicios punto-a-multipunto, hubo investigación en entornos acad\'emicos y colaboraciones público-privada. La iniciativa más notable en este aspecto fue el proyecto del Horizon 2020 5G-Xcast, que transcurrió de 2017 a 2019. 5G-Xcast produjo varias soluciones a nivel de arquitectura, desde la perspectiva de provisión de contenidos, nuevas funciones de red interoperables con el núcleo 5G, hasta modificaciones a la interfaz aire basada en New Radio. Los hallazgos del proyecto están descritos en esta tesis. La tesis incluye dos ejemplos de eMBMS aplicados a verticales diferentes, una para el uso de eMBMS en entornos industriales, y otra presentando eMBMS como un sistema SAP. Incluir servicios punto-a-multipunto como un modo adicional celular trae algunos desafíos, como ya mostró la estandarización de eMBMS: las redes de radiodifusión terrestre y las redes celulares son muy distintas entre ellas. Encontrar una forma de onda viable para ambas infraestructuras es complejo. Esta tesis ofrece un punto de vista distinto al problema: un escenario de colaboración entre cadenas televisivas y operadores móviles, donde la infraestructura de radiodifusión y móvil son compartidas. Este concepto se ha definido como Convergence of Terrestrial and Mobile Networks. Las tecnologías elegidas para converger son ATSC 3.0 y 5G, usando el Advanced Traffic Steering, Switching and Splitting (ATSSS). ATSSS está compuesto de una serie de procedimientos, interfaces, funciones de red, para permitir el uso compartido de un acceso 3GPP con uno non-3GPP, como Wi-Fi. Sin embargo, el uso de ATSSS para juntar radiodifusión y celular no es trivial, ya que ATSSS no fue dise\~{n}ado para enlaces radio unidireccionales como ATSC 3.0. Estas limitaciones son descritas en detalle, y una propuesta para solventarlas tambi\'en está incluida. La solución se basa en Quick UDP Internet Connections (QUIC), y se usa como ejemplo para la provisión de Convergent Services (File Repair y Video Offloading). La tesis concluye con una descripción de Release 17 5MBS, con los nuevos conceptos introducidos. 5MBS es capaz de cambiar entre unicast, multicast y broadcast; dependiendo del servicio, la ubicación geográfica de los usuarios, y las capacidades de la infraestructura móvil involucradas. Para evaluar 5MBS, se ha realizado un estudio de prestaciones, basado en comunicaciones multicast dentro del núcleo de red 5G. Este prototipo 5MBS forma parte del laboratorio VLC Campus 5G, y utiliza el software comercial Open5GCore como base del desarrollo. El modelo de sistema para la experimentación esta formado por un servidor de vídeo, que se conecta al Open5GCore y a las funciones de red mejoradas con funcionalidades 5MBS. Estas funciones de red envían el contenido mediante punto-a-multipunto a un entorno radio y terminales simulados. Los resultados obtenidos resaltan el objetivo principal de la tesis: las comunicaciones punto-a-multipunto son una solución escalable para el envío de contenido multimedia en directo.[CA] Aquesta dissertació cobreix capdavanter en LTE eMBMS Release 14, també conegut com Enhanced Television Services (ENTV). ENTV va portar un conjunt de millores, tant a nivell de ràdio com a nivell de nucli, que va transformar el eMBMS en un estàndard de televisió terrestre complet. La última versió d'aquesta tecnologia es denomina LTE-based 5G Broadcast; però no fa servir New Ràdio ni el nucli 5G. Per a proveir una solució nativa 5G de serveis punt-a-multipunt, va haver-hi investigació en entorns acadèmics i col·laboracions pública i privada. La iniciativa més notable en aquest aspecte va ser el projecte del Horizon 2020 5G-Xcast, que va transcórrer del 2017 a 2019. 5G-Xcast va produir diverses solucions a nivell d'arquitectura, des de la perspectiva de provisió de continguts, noves funcions de xarxa interoperables amb el nucli 5G, fins a modificacions a la interfície aire basada en New Radio. Les troballes del projecte estan descrits en aquesta tesi. La tesi inclou dos exemples de eMBMS aplicats a verticals diferents, una per a l'ús de eMBMS en entorns industrials, i una altra presentant eMBMS com un sistema SAP. Incloure serveis punt-a-multipunt com una manera addicional cel·lular duu alguns desafiaments, com ja va mostrar l'estandardització de eMBMS: les xarxes de radiodifusió terrestre i les xarxes cel·lulars són molt diferents entre elles. Trobar una forma d'ona viable per a totes dues infraestructures és complex. Aquesta tesi ofereix un punt de vista diferent al problema: un escenari de col·laboració entre cadenes televisives i operadors mòbils, on la infraestructura de radiodifusió i mòbil són compartides. Aquest concepte s'ha definit com Convergence of Terrestrial and Mobile Networks. Les tecnologies triades per a convergir són ATSC 3.0 i 5G, usant el Advanced Traffic Steering, Switching and Splitting (ATSSS). ATSSS està compost d'una sèrie de procediments, interfícies, funcions de xarxa, per a permetre l'ús compartit d'un accés 3GPP amb un non-3GPP, com a Wi-Fi. No obstant això, l'ús de ATSSS per a adjuntar radiodifusió i cel·lular no és trivial, ja que ATSSS no va ser dissenyada per a per a enllaços ràdio unidireccionals com ATSC 3.0. Aquestes limitacions són descrites detalladament, i una proposta per a solucionar-les també està inclosa. La solució es basa en Quick UDP Internet Connections (QUIC), i s'usa com a exemple per a la provisió de Convergent Services (File Repair i Vídeo Offloading). La tesi conclou amb una descripció de Release 17 5MBS, amb els nous conceptes introduïts. 5MBS és capaç de canviar entre unicast, multicast i broadcast; depenent del servei, la ubicació geogràfica dels usuaris, i les capacitats de la infraestructura mòbil involucrades. Per a avaluar 5MBS, s'ha realitzat un estudi de prestacions, basat en comunicacions multicast dins del nucli de xarxa 5G. Aquest prototip 5MBS forma part del laboratori VLC Campus 5G, i utilitza el programari comercial Open5GCore com a base del desenvolupament. El model de sistema per a l'experimentació està format per un servidor de vídeo, que es connecta al Open5GCore i a les funcions de xarxa millorades amb funcionalitats 5MBS. Aquestes funcions de xarxa envien el contingut mitjançant punt-a-multipunt a un entorn ràdio i terminals simulats. Els resultats obtinguts ressalten l'objectiu principal de la tesi: les comunicacions punt-a-multipunt són una solució escalable per a l'enviament de contingut multimèdia en directe.[EN] This dissertation covers the state-of-the-art in LTE eMBMS Release 14, also known as Enhanced Television Services (ENTV). ENTV provided a suite of radio and core enhancements that made eMBMS into a viable terrestrial broadcast standard. The latest iteration of this technology is known as LTE-based 5G Broadcast; even though it is not New Radio or 5G Core based. To bridge this gap, research efforts by academia, public and private enterprises evaluated how to provide a 5G-based solution for point-to-multipoint services. The most notable effort in this regard is the Horizon 2020 project 5G-Xcast, which ran from 2017 to 2019. 5G-Xcast provided several architectural solutions, from the content delivery perspective down to air interface specifics; providing new waveforms based on New Radio and Network Functions interoperable with a Release 15 5G Core. The findings are summarized in this thesis. Two examples of eMBMS applied to different verticals are included in the thesis, one for the use of eMBMS in industrial environments, and the other using eMBMS as a PWS technology. Providing point-to-multipoint services as another cellular service poses some problems, as the standardization process of eMBMS showed: the broadcast infrastructure is different than the cellular one. Having a waveform that is suited for both scenarios is a difficult endeavour. The thesis provides a new perspective into this problem: Having existing Terrestrial Broadcast standards and infrastructure be the point-to-multipoint solution of 5G, where mobile operators and broadcasters collaborate together. This is defined in the dissertation as Convergence of Terrestrial and Mobile Networks. The technologies chosen to be converged together were ATSC 3.0 and 5G; using the existing Release 16 framework known as Advanced Traffic Steering, Switching and Splitting (ATSSS). ATSSS is a series of procedures, interfaces, new Network Functions, to allow the joint use of a 3GPP Access Network alongside a non-3GPP one, like Wi-Fi. However, the use of ATSSS for cellular plus broadcast brings challenges, as the ATSSS technology was not designed to be used with a unidirectional access network like ATSC 3.0. These limitations are described in detail, and an architectural proposal that overcomes the limitations is proposed. This solution is based on Quick UDP Internet Connections (QUIC), and how to provide Convergent Services (i.e File Repair and Video Offloading) is shown. The thesis concludes with a description of Release 17 5MBS, including the new concepts introduced. 5MBS features the capacity of switching between unicast, multicast and broadcast; depending on the service addressed, the geographical location of the users, and the capability of the RAN infrastructure targeted. In order to evaluate 5MBS, a performance study of the use of multicast inside the 5G Core has been carried out. The 5MBS prototype was developed as part of the VLC Campus 5G laboratory, using the commercial software Open5GCore which provides the libraries and Network Functions to deploy your own 5G Private Network in testing environments. The system model of the experiment is formed by a video server, connected to the Open5GCore and the 5MBS enhanced functions; which will deliver the content to an emulated RAN environment hosting virtual gNBs and devices. The results obtained reinforce the objective of the thesis, positioning point-to-multipoint as a scalable way to deliver live content.Research projects: 5G-Xcast: Broadcast and Multicast Communication Enablers for the Fifth-Generation of Wireless Systems (H2020 No 761498); 5G-TOURS: SmarT mObility, media and e-health for toURists and citizenS (H2020 No 856950); FUDGE-5G: FUlly DisinteGrated private nEtworks for 5G verticals (H2020 No 957242).Barjau Estevan, CS. (2022). Point-to-Multipoint Services on Fifth-Generation Mobile Networks [Tesis doctoral]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/19140

Analog radio over fiber solutions for multi-band 5g systems

This study presents radio over fiber (RoF) solutions for the fifth-generation (5G) of wireless networks. After the state of the art and a technical background review, four main contributions are reported. The first one is proposing and investigating a RoF technique based on a dual-drive Mach-Zehnder modulator (DD-MZM) for multi-band mobile fronthauls, in which two radiofrequency (RF) signals in the predicted 5G bands individually feed an arm of the optical modulator. Experimental results demonstrate the approach enhances the RF interference mitigation and can prevail over traditional methods. The second contribution comprises the integration of a 5G transceiver, previously developed by our group, in a passive optical network (PON) using RoF technology and wavelength division multiplexing (WDM) overlay. The proposed architecture innovates by employing DD-MZM and enables to simultaneously transport baseband and 5G candidate RF signals in the same PON infrastructure. The proof-of-concept includes the transmission of a generalized frequency division multiplexing (GFDM) signal generated by the 5G transceiver in the 700 MHz band, a 26 GHz digitally modulated signal as a millimeter-waves 5G band, and a baseband signal from an gigabit PON (GPON). Experimental results demonstrate the 5G transceiver digital performance when using RoF technology for distributing the GFDM signal, as well as Gbit/s throughput at 26 GHz. The third contribution is the implementation of a flexible-waveform and multi-application fiber-wireless (FiWi) system toward 5G. Such system includes the FiWi transmission of the GFDM and filtered orthogonal frequency division multiplexing (F-OFDM) signals at 788 MHz, toward long-range cells for remote or rural mobile access, as well as the recently launched 5G NR standard in microwave and mm-waves, aiming enhanced mobile broadband indoor and outdoor applications. Digital signal processing (DSP) is used for selecting the waveform and linearizing the RoF link. Experimental results demonstrate the suitability of the proposed solution to address 5G scenarios and requirements, besides the applicability of using existent fiber-to-the-home (FTTH) networks from Internet service providers for implementing 5G systems. Finally, the fourth contribution is the implementation of a multi-band 5G NR system with photonic-assisted RF amplification (PAA). The approach takes advantage of a novel PAA technique, based on RoF technology and four-wave mixing effect, that allows straightforward integration to the transport networks. Experimental results demonstrate iv uniform and stable 15 dB wideband gain for Long Term Evolution (LTE) and three 5G signals, distributed in the frequency range from 780 MHz to 26 GHz and coexisting in the mobile fronthaul. The obtained digital performance has efficiently met the Third-Generation Partnership Project (3GPP) requirements, demonstrating the applicability of the proposed approach for using fiber-optic links to distribute and jointly amplify LTE and 5G signals in the optical domain.Agência 1Este trabalho apresenta soluções de rádio sobre fibra (RoF) para aplicações em redes sem fio de quinta geração (5G), e inclui quatro contribuições principais. A primeira delas refere-se à proposta e investigação de uma técnica de RoF baseada no modulador eletroóptico de braço duplo, dual-drive Mach-Zehnder (DD-MZM), para a transmissão simultânea de sinais de radiofrequência (RF) em bandas previstas para redes 5G. Resultados experimentais demonstram que o uso do DD-MZM favorece a ausência de interferência entre os sinais de RF transmitidos. A segunda contribuição trata da integração de um transceptor de RF, desenvolvido para aplicações 5G e apto a prover a forma de onda conhecida como generalized frequency division multiplexing (GFDM), em uma rede óptica passiva (PON) ao utilizar RoF e multiplexação por divisão de comprimento de onda (WDM). A arquitetura proposta permite transportar, na mesma infraestrutura de rede, sinais em banda base e de radiofrequência nas faixas do espectro candidatas para 5G. A prova de conceito inclui a distribuição conjunta de três tipos de sinais: um sinal GFDM na banda de 700 MHz, proveniente do transceptor desenvolvido; um sinal digital na frequência de 26 GHz, assumindo a faixa de ondas milimétricas; sinais em banda base provenientes de uma PON dedicada ao serviço de Internet. Resultados experimentais demonstram o desempenho do transceptor de RF ao utilizar a referida arquitetura para distribuir sinais GFDM, além de taxas de transmissão de dados da ordem de Gbit/s na faixa de 26 GHz. A terceira contribuição corresponde à implementação de um sistema fibra/rádio potencial para redes 5G, operando inclusive com o padrão ―5G New Radio (5G NR)‖ nas faixas de micro-ondas e ondas milimétricas. Tal sistema é capaz de prover macro células na banda de 700 MHz para aplicações de longo alcance e/ou rurais, utilizando sinais GFDM ou filtered orthogonal frequency division multiplexing (F-OFDM), assim como femto células na banda de 26 GHz, destinada a altas taxas de transmissão de dados para comunicações de curto alcance. Resultados experimentais demonstram a aplicabilidade da solução proposta para redes 5G, além da viabilidade de utilizar redes ópticas pertencentes a provedores de Internet para favorecer sistemas de nova geração. Por fim, a quarta contribuição trata da implementação de um sistema 5G NR multibanda, assistido por amplificação de RF no domínio óptico. Esse sistema faz uso de um novo método de amplificação, baseado no efeito não linear da mistura de quatro ondas, que vi permite integração direta em redes de transporte envolvendo rádio sobre fibra. Resultados experimentais demonstram ganho de RF igual a 15 dB em uma ampla faixa de frequências (700 MHz até 26 GHz), atendendo simultaneamente tecnologias de quarta e quinta geração. O desempenho digital obtido atendeu aos requisitos estabelecidos pela 3GPP (Third-Generation Partnership Project), indicando a aplicabilidade da solução em questão para distribuir e conjuntamente amplificar sinais de RF em enlaces de fibra óptica

Integration of unidirectional technologies into wireless back-haul architecture

This thesis was submitted for the degree of Docter of Philosophy and awarded by Brunel University.Back-haul infrastructures of today's wireless operators must support the triple-play services demanded by the market or regulatory bodies. To cope with increasing capacity demand, the EU FP7 project CARMEN has developed a cost-effective heterogeneous multi-radio wireless back-haul architecture, which may also leverage the native multicast capabilities of broadcast technologies such as DVB-T to off-load high-bandwidth broadcast content delivery. However, the integration of such unidirectional technologies into a packet-switched architecture requires careful considerations. The contribution of this thesis is the investigation, design and evaluation of protocols and mechanisms facilitating the integration of such unidirectional technologies into the wireless back-haul architecture so that they can be configured and utilized by the spectrum and capacity optimization modules. This integration mainly concerns the control plane and, in particular, the aspects related to resource and capability descriptions, neighborhood, link and Multi Protocol Label Switching (MPLS) Label-Switched Path (LSP) monitoring, unicast and multicast LSP signalling as well as topology forming and maintenance. During the course of this study we have analyzed the problem space, proposed solutions to the resulting research questions and evaluated our approach. Our results show that the now Unidirectional Technology (UDT)-aware architecture can readily consider Unidirectional Technologies (UDTs) to distribute, for example, broadcast content

Multimedia delivery in the future internet

The term “Networked Media” implies that all kinds of media including text, image, 3D graphics, audio and video are produced, distributed, shared, managed and consumed on-line through various networks, like the Internet, Fiber, WiFi, WiMAX, GPRS, 3G and so on, in a convergent manner [1]. This white paper is the contribution of the Media Delivery Platform (MDP) cluster and aims to cover the Networked challenges of the Networked Media in the transition to the Future of the Internet. Internet has evolved and changed the way we work and live. End users of the Internet have been confronted with a bewildering range of media, services and applications and of technological innovations concerning media formats, wireless networks, terminal types and capabilities. And there is little evidence that the pace of this innovation is slowing. Today, over one billion of users access the Internet on regular basis, more than 100 million users have downloaded at least one (multi)media file and over 47 millions of them do so regularly, searching in more than 160 Exabytes1 of content. In the near future these numbers are expected to exponentially rise. It is expected that the Internet content will be increased by at least a factor of 6, rising to more than 990 Exabytes before 2012, fuelled mainly by the users themselves. Moreover, it is envisaged that in a near- to mid-term future, the Internet will provide the means to share and distribute (new) multimedia content and services with superior quality and striking flexibility, in a trusted and personalized way, improving citizens’ quality of life, working conditions, edutainment and safety. In this evolving environment, new transport protocols, new multimedia encoding schemes, cross-layer inthe network adaptation, machine-to-machine communication (including RFIDs), rich 3D content as well as community networks and the use of peer-to-peer (P2P) overlays are expected to generate new models of interaction and cooperation, and be able to support enhanced perceived quality-of-experience (PQoE) and innovative applications “on the move”, like virtual collaboration environments, personalised services/ media, virtual sport groups, on-line gaming, edutainment. In this context, the interaction with content combined with interactive/multimedia search capabilities across distributed repositories, opportunistic P2P networks and the dynamic adaptation to the characteristics of diverse mobile terminals are expected to contribute towards such a vision. Based on work that has taken place in a number of EC co-funded projects, in Framework Program 6 (FP6) and Framework Program 7 (FP7), a group of experts and technology visionaries have voluntarily contributed in this white paper aiming to describe the status, the state-of-the art, the challenges and the way ahead in the area of Content Aware media delivery platforms

Fixed Broadband Wireless Systems

Diplomska naloga opisuje fiksne brezžične širokopasovne sisteme. Opisani so sistemi, ki so jih pred dolgimi leti razvili z namenom distribucije televizijskih programov in sistemi, ki jih uporabljamo danes in omogočajo dvosmerni prenos interneta ter telefonije preko interneta. Bolj podrobno so opisani tudi sistemi, ki jih uporabljamo oz. tisti, ki jih bomo v Sloveniji še uporabljali. Fiksni širokopasovni brezžični sistemi se razlikujejo glede na proizvajalca in na ponudnika storitve, zato so na kratko predstavljene osnovne lastnosti in zgradba najbolj osnovnega sistema, iz katerega izhajajo nadaljnji sistemi. Uporabljajo se lahko različne frekvence, zato je opisano tudi, kako reagirajo različne frekvence v brezžičnem prostoru. Predstavljeni so različni sistemi, ki delujejo na različnih frekvenčnih območjih. Zaradi hitrega širjenja fiksnih brezžičnih širokopasovnih sistemov so se začele pojavljati motnje med njimi in drugimi sistemi na določenih frekvenčnih območjih. Opisane so tudi najpogostejše motnje in v katerih frekvenčnih območjih se pojavljajo. Slovenija je ena od držav, ki uporablja te sisteme za distribucijo dvosmernega širokopasovnega prenosa. Predstavljena so frekvenčna območja, ki so namenjena fiksnim širokopasovnim brezžičnim sistemom na slovenskem ozemlju in nekatera pravila, ki jih morajo operaterji upoštevati.This thesis describes fixed broadband wireless systems. Also described are systems that have been developed for distributing television programs and systems that are being currently used for bi-directional internet and IP-telephony transmission. The systems that are used in Slovenia are described in more details. Fixed broadband wireless systems can be very different, depending on the manufacturer and service provider. Because of that, the most common system from which all others originate, is described in the thesis. The systems can use different frequencies and because of that, the thesis describes how different frequencies react in the wireless environment. Systems that operate on various frequency bands are also described. The number of interferences between systems at certain frequencies has grown due to the rapid expansion of fixed wireless broadband systems. Also described in the thesis are the most common interferences and in which frequency bands they occur. Slovenia is one of the countries that use those systems for bi-directional broadband distribution. Frequency bands that are used for fixed wireless broadband systems and certain rules service providers on Slovenian territory are obliged to follow are also introduced in the thesis