Power consumption modeling in optical multilayer networks

The evaluation of and reduction in energy consumption of backbone telecommunication networks has been a popular subject of academic research for the last decade. A critical parameter in these studies is the power consumption of the individual network devices. It appears that across different studies, a wide range of power values for similar equipment is used. This is a result of the scattered and limited availability of power values for optical multilayer network equipment. We propose reference power consumption values for Internet protocol/multiprotocol label switching, Ethernet, optical transport networking and wavelength division multiplexing equipment. In addition we present a simplified analytical power consumption model that can be used for large networks where simulation is computationally expensive or unfeasible. For illustration and evaluation purpose, we apply both calculation approaches to a case study, which includes an optical bypass scenario. Our results show that the analytical model approximates the simulation result to over 90% or higher and that optical bypass potentially can save up to 50% of power over a non-bypass scenario

Energy-efficient traffic engineering

The energy consumption in telecommunication networks is expected to grow considerably, especially in core networks. In this chapter, optimization of energy consumption is approached from two directions. In a first study, multilayer traffic engineering (MLTE) is used to assign energy-efficient paths and logical topology to IP traffic. The relation with traditional capacity optimization is explained, and the MLTE strategy is applied for daily traffic variations. A second study considers the core network below the IP layer, giving a detailed power consumption model. Optical bypass is evaluated as a technique to achieve considerable power savings over per-hop opticalelectronicoptical regeneration. Document type: Part of book or chapter of boo

Power consumption evaluation of circuit-switched versus packet-switched optical backbone networks

While telecommunication networks have historically been dominated by a circuit-switched paradigm, the last decades have seen a clear trend towards packet-switched networks. In this paper we evaluate how both paradigms perform in optical backbone networks from a power consumption point of view, and whether the general agreement of circuit switching being more power-efficient holds. We consider artificially generated topologies of various sizes, mesh degrees and not yet previously explored in this context transport linerates. We cross-validate our findings with a number of realistic topologies. Our results show that, as a generalization, packet switching can become preferable when the traffic demands are lower than half the transport linerate. We find that an increase in the network node count does not consistently increase the energy savings of circuit switching over packet switching, but is heavily influenced by the mesh degree and (to a minor extent) by the average link length

Cross-layer modeling and optimization of next-generation internet networks

Scaling traditional telecommunication networks so that they are able to cope with the volume of future traffic demands and the stringent European Commission (EC) regulations on emissions would entail unaffordable investments. For this very reason, the design of an innovative ultra-high bandwidth power-efficient network architecture is nowadays a bold topic within the research community. So far, the independent evolution of network layers has resulted in isolated, and hence, far-from-optimal contributions, which have eventually led to the issues today's networks are facing such as inefficient energy strategy, limited network scalability and flexibility, reduced network manageability and increased overall network and customer services costs. Consequently, there is currently large consensus among network operators and the research community that cross-layer interaction and coordination is fundamental for the proper architectural design of next-generation Internet networks. This thesis actively contributes to the this goal by addressing the modeling, optimization and performance analysis of a set of potential technologies to be deployed in future cross-layer network architectures. By applying a transversal design approach (i.e., joint consideration of several network layers), we aim for achieving the maximization of the integration of the different network layers involved in each specific problem. To this end, Part I provides a comprehensive evaluation of optical transport networks (OTNs) based on layer 2 (L2) sub-wavelength switching (SWS) technologies, also taking into consideration the impact of physical layer impairments (PLIs) (L0 phenomena). Indeed, the recent and relevant advances in optical technologies have dramatically increased the impact that PLIs have on the optical signal quality, particularly in the context of SWS networks. Then, in Part II of the thesis, we present a set of case studies where it is shown that the application of operations research (OR) methodologies in the desing/planning stage of future cross-layer Internet network architectures leads to the successful joint optimization of key network performance indicators (KPIs) such as cost (i.e., CAPEX/OPEX), resources usage and energy consumption. OR can definitely play an important role by allowing network designers/architects to obtain good near-optimal solutions to real-sized problems within practical running times

Logical topology design for IP rerouting: ASONs versus static OTNs

IP-based backbone networks are gradually moving to a network model consisting of high-speed routers that are flexibly interconnected by a mesh of light paths set up by an optical transport network that consists of wavelength division multiplexing (WDM) links and optical cross-connects. In such a model, the generalized MPLS protocol suite could provide the IP centric control plane component that will be used to deliver rapid and dynamic circuit provisioning of end-to-end optical light paths between the routers. This is called an automatic switched optical (transport) network (ASON). An ASON enables reconfiguration of the logical IP topology by setting up and tearing down light paths. This allows to up- or downgrade link capacities during a router failure to the capacities needed by the new routing of the affected traffic. Such survivability against (single) IP router failures is cost-effective, as capacity to the IP layer can be provided flexibly when necessary. We present and investigate a logical topology optimization problem that minimizes the total amount or cost of the needed resources (interfaces, wavelengths, WDM line-systems, amplifiers, etc.) in both the IP and the optical layer. A novel optimization aspect in this problem is the possibility, as a result of the ASON, to reuse the physical resources (like interface cards and WDM line-systems) over the different network states (the failure-free and all the router failure scenarios). We devised a simple optimization strategy to investigate the cost of the ASON approach and compare it with other schemes that survive single router failures

Finding an objective cost for sliceable flexgrid transponders

We analyze the objective cost of SBVTs as a function of the traffic conveyed by IP/MPLS-over-flexgrid networks. Optimal results show that cost increment with respect to BVTs is related to the aggregation level.Postprint (published version

Topological Design of Multiple Virtual Private Networks UTILIZING SINK-TREE PATHS

With the deployment of MultiProtocol Label Switching (MPLS) over a core backbone networks, it is possible for a service provider to built Virtual Private Networks (VPNs) supporting various classes of services with QoS guarantees. Efficiently mapping the logical layout of multiple VPNs over a service provider network is a challenging traffic engineering problem. The use of sink-tree (multipoint-to-point) routing paths in a MPLS network makes the VPN design problem different from traditional design approaches where a full-mesh of point-to-point paths is often the choice. The clear benefits of using sink-tree paths are the reduction in the number of label switch paths and bandwidth savings due to larger granularities of bandwidth aggregation within the network. In this thesis, the design of multiple VPNs over a MPLS-like infrastructure network, using sink-tree routing, is formulated as a mixed integer programming problem to simultaneously find a set of VPN logical topologies and their dimensions to carry multi-service, multi-hour traffic from various customers. Such a problem formulation yields a NP-hard complexity. A heuristic path selection algorithm is proposed here to scale the VPN design problem by choosing a small-but-good candidate set of feasible sink-tree paths over which the optimal routes and capacity assignments are determined. The proposed heuristic has clearly shown to speed up the optimization process and the solution can be obtained within a reasonable time for a realistic-size network. Nevertheless, when a large number of VPNs are being layout simultaneously, a standard optimization approach has a limited scalability. Here, the heuristics termed the Minimum-Capacity Sink-Tree Assignment (MCSTA) algorithm proposed to approximate the optimal bandwidth and sink-tree route assignment for multiple VPNs within a polynomial computational time. Numerical results demonstrate the MCSTA algorithm yields a good solution within a small error and sometimes yields the exact solution. Lastly, the proposed VPN design models and solution algorithms are extended for multipoint traffic demand including multipoint-to-point and broadcasting connections

Towards faster techno-economic evaluation of network scenarios via a modular network equipment database

Techno-economic analysis is used to evaluate technological solutions in different business environments via a simulation based approach. Four steps can be observed in techno-economic analysis: scope definition, modeling of costs and revenues, evaluation of the different solutions and refinement of the analysis. During the scoping step, the boundaries of the analysis are determined, the problem is divided into sub problems and a list of input values is collected. The collection of complete and precise inputs is of the greatest importance as faulty data leads to unreliable results (garbage in garbage out). Today, due to the lack of a structured way of sharing input values, inputs need to be collected on a case-by-case basis. Although a valid approach, it remains a time intensive process prone to errors. This paper therefore proposes a modular network equipment database containing a set of generic equipment such as an IP/MPLS router, a DWDM node, a fiber link and a twisted pair cable. Each of these is represented as a modular block model and described by a set of attributes and a set of drivers which are used to chain one network equipment's block model to one or more others. A complex network can as such be modeled as a chain of equipment block models which are determined by a set of drivers. As a consequence, the collection of inputs can be fast tracked, the problem of missing inputs can be partially resolved and cross-case comparison becomes possible. To make things more concrete, we illustrate this approach via the evaluation of a network scenario in which a network service provider expands its network with an extra core location