Multi-level integrated optimal design for power systems of more electric aircraft

This paper proposes a multi-level optimal design method for a complex actuation system of more electric aircraft. The multilevel structure consists in sharing the optimization process in several levels, here 2, a “system level” which involves main coupling variables and a “component level” with one optimization loop for each device. The interest of this method is to separate the optimal design of each component, making easier the convergence of loops. This method is applied to a relatively complex power conversion system including a high speed permanent magnet synchronous machine (HSPMSM) supplied by a pulse width modulation (PWM) voltage source inverter (VSI) associated with a DC-link filter. Its interest is shown through a comparison with classical design approaches employed in previous works

Generator Power Optimisation for a More-Electric Aircraft by Use of a Virtual Iron Bird

A prodedure is developed to minimise the generator design power within the electric power system of a future more-/ all-electric aircraft. This allows to save weight on the generators and on other equipment of the electic power system. Execution of the optimisation procedure by hand demonstrates the complexity of the problem. An automation of the process shows the capabilities of integrated modelling, simulation and optimisation tools

Modeling and simulation enabled UAV electrical power system design

With the diversity of mission capability and the associated requirement for more advanced technologies, designing modern unmanned aerial vehicle (UAV) systems is an especially challenging task. In particular, the increasing reliance on the electrical power system for delivering key aircraft functions, both electrical and mechanical, requires that a systems-approach be employed in their development. A key factor in this process is the use of modeling and simulation to inform upon critical design choices made. However, effective systems-level simulation of complex UAV power systems presents many challenges, which must be addressed to maximize the value of such methods. This paper presents the initial stages of a power system design process for a medium altitude long endurance (MALE) UAV focusing particularly on the development of three full candidate architecture models and associated technologies. The unique challenges faced in developing such a suite of models and their ultimate role in the design process is explored, with case studies presented to reinforce key points. The role of the developed models in supporting the design process is then discussed

Environmental Impact Assessment, on the Operation of Conventional and More Electric Large Commercial Aircraft

Global aviation is growing exponentially and there is a great emphasis on trajectory optimization to reduce the overall environmental impact caused by aircraft. Many optimization techniques exist and are being studied for this purpose. The CLEAN SKY Joint Technology Initiative for aeronautics and Air transport, a European research activity run under the Seventh Framework program, is a collaborative initiative involving industry, research organizations and academia to introduce novel technologies to improve the environmental impact of aviation. As part of the overall research activities, "green" aircraft trajectories are addressed in the Systems for Green Operations (SGO) Integrated Technology Demonstrator. This paper studies the impact of large commercial aircraft trajectories optimized for different objectives applied to the on board systems. It establishes integrated systems models for both conventional and more electric secondary power systems and studies the impact of fuel, noise, time and emissions optimized trajectories on each configuration. It shows the significant change in the fuel burn due to systems operation and builds up the case as to why a detailed aircraft systems model is required within the optimization loop. Typically, the objective in trajectory optimization is to improve the mission performance of an aircraft or reduce the environmental impact. Hence parameters such as time, fuel burn, emissions and noise are key optimization objectives. In most instances, trajectory optimization is achieved by using models that represent such parameters. For example aircraft dynamics models to describe the flight performance, engine models to calculate the fuel burn, emissions and noise impact, etc. Such techniques have proved to achieve the necessary level of accuracy in trajectory optimization. This research enhances previous techniques by adding in the effect of systems power in the optimization process. A comparison is also made between conventional power systems and more electric architectures. In the conventional architecture, the environmental control system and the ice protection system are powered by engine bleed air while actuators and electrics are powered by engine shaft power off-takes. In the more electric architecture, bleed off take is eliminated and the environmental control system and ice protection system are also powered electrically through engine shaft power off takes

Determination of protection system requirements for DC UAV electrical power networks for enhanced capability and survivability

A growing number of designs of future Unmanned Aerial Vehicle (UAV) applications utilise dc for the primary power distribution method. Such systems typically employ large numbers of power electronic converters as interfaces for novel loads and generators. The characteristic behaviour of these systems under electrical fault conditions, and in particular their natural response, can produce particularly demanding protection requirements. Whilst a number of protection methods for multi-terminal dc networks have been proposed in literature, these are not universally applicable and will not meet the specific protection challenges associated with the aerospace domain. Through extensive analysis, this paper seeks to determine the operating requirements of protection systems for compact dc networks proposed for future UAV applications, with particular emphasis on dealing with the issues of capacitive discharge in these compact networks. The capability of existing multi-terminal dc network protection methods and technologies are then assessed against these criteria in order to determine their suitability for UAV applications. Recommendations for best protection practice are then proposed and key inhibiting research challenges are discussed

Feasibility of Electrified Propulsion for Ultra-Efficient Commercial Aircraft Final Report

MIT, Aurora Flight Sciences, and USC have collaborated to assess the feasibility of electric, hybridelectric, and turbo-electric propulsion for ultra-efficient commercial transportation. The work has drawn on the team expertise in disciplines related to aircraft design, propulsion-airframe integration, electric machines and systems, engineering system design, and optimization. A parametric trade space analysis has been carried out to assess vehicle performance across a range of transport missions and propulsion architectures to establish how electrified propulsion systems scale. An optimization approach to vehicle conceptual design modeling was taken to enable rapid multidisciplinary design space exploration and sensitivity analysis. The results of the analysis indicate vehicle aero-propulsive integration benefits enabled by electrification are required to offset the increased weight and loss associated with the electric system and achieve enhanced performance; the report describes the conceptual configurations than can offer such enhancements. The main contribution of the present work is the definition of electric vehicle design attributes for potential efficiency improvements at different scales. Based on these results, key areas for future research are identified, and extensions to the trade space analysis suitable for higher fidelity electrified commercial aircraft design and analysis have been developed

Set-based approach to passenger aircraft family design

Presented is a method for the design of passenger aircraft families. Existing point-based methods found in the literature employ sequential approaches in which a single design solution is selected early and is then iteratively modified until all requirements are satisfied. The challenge with such approaches is that the design is driven toward a solution that, although promising to the optimizer, may be infeasible due to factors not considered by the models. The proposed method generates multiple solutions at the outset. Then, the infeasible solutions are discarded gradually through constraint satisfaction and set intersection. The method has been evaluated through a notional example of a three-member aircraft family design. The conclusion is that point-based design is still seen as preferable for incremental (conventional) designs based on a wealth of validated empirical methods, whereas the proposed approach, although resource-intensive, is seen as more suited to innovative designs