Advanced Strategies for Robot Manipulators

Amongst the robotic systems, robot manipulators have proven themselves to be of increasing importance and are widely adopted to substitute for human in repetitive and/or hazardous tasks. Modern manipulators are designed complicatedly and need to do more precise, crucial and critical tasks. So, the simple traditional control methods cannot be efficient, and advanced control strategies with considering special constraints are needed to establish. In spite of the fact that groundbreaking researches have been carried out in this realm until now, there are still many novel aspects which have to be explored

Design and Development of a Tele-operated Surgical Simulation Environment

With the introduction of robots into laparoscopic surgery, surgeons have difficulties in selecting the placement of the incisions required to insert the robots instruments into the body and also determine which patients are suitable for robotically assisted surgery. Poor selection of these two items mentioned above can result in a conversion to a more invasive form of surgery during the procedure. This work introduces the design and development of a surgical simulation environment to assist in the research for optimal incision placement and patient selection. The simulator allows importing any serial link robot that was designed in a computer aided modelling package. With minimal added information, the imported robot can be controlled using a multi-degree of freedom user input device. The simulator allows for importing patient geometries along with the robot to allow for the simulation of surgical procedures. A Jacobian transpose algorithm was added onto the simulator in a modular format to control the simulated robots, as well as to allow for other control systems to be created and implemented. Experiments were performed to determine the effects of patient geometry models on rendering speeds. The control system could control the tested robots with a maximum lag time of 15 ms between moving the input device and the simulated robot moving to the correct desired position. The simulator makes importing and controlling robots a simple and intuitive matter, without putting a large restriction on the type of robots to be simulated. The simulator also allows for importing models of a patient, to make real world analysis of a patient possible. Further improvements on the presented simulator include the addition of collision detection and more testing on the control system for stability and response over a larger range of robots

Ein mobiler Serviceroboter zur Automatisierung der Probenahme und des Probenmanagements in einem biotechnologischen Pilotlabor

Scherer T. A mobile service robot for automisation of sample taking and sample management in a biotechnological pilot laboratory. Bielefeld (Germany): Bielefeld University; 2004.In biotechnologischen Laboratorien ist die Qualität der typischerweise pharmazeutischen Produkte ein wortwörtlich lebenswichtiges Ziel. Die Qualität der Zellkultivierungen wurde historisch nur durch off-line Messungen von physikalischen Prozessparametern wie pH und pO2 sichergestellt. Biologische Parameter wie die Zelldichte und -viabilität wurden nur off-line gemessen, weil das dazu notwendige Probenmanagement hochkomplizierte Manipulationen und Analysen beinhaltet und deshalb nicht automatisiert werden konnte. Es gibt zwar mehrere automatisierte Geräte, um einem Labortechniker zu assistieren, aber kein System, welches das gesamte Probenmanagement automatisiert. In dieser Arbeit wird ein neuer Typ von Serviceroboter präsentiert, der aus einem auf einer mobilen Plattform montierten Roboterarm besteht und diese Lücke schließt. Dieser Roboter muss eine ganze Reihe von Problemen bewältigen: Er muss seine Position im Labor bestimmen können (Lokalisation), er muss eine kollisionsfreie Bahn zu den beteiligten Geräten finden können (Bahnplanung mit Hindernisvermeidung), er darf bei seinen Bewegungen keine Menschen gefährden oder Laborausrüstung beschädigen (Kollisionsvermeidung), er muss die zu bedienenden Geräte erkennen und ihre Position präzise messen können (Bildverarbeitung), er muss sie bedienen können (Armsteuerung), er muss Objekte greifen können (Greifer und Finger) und er muss sie gefügig handhaben können, um sie nicht zu beschädigen (Kraftregelung). Er muss autonom sein, um nur die allernotwendigste Menge an Benutzereingriffen zu benötigen, und doch durch ein Laborsteuerprogramm kontrollierbar sein, um Eingriffe zu erlauben. Schließlich muss er einfach durch ungeschultes Personal zu warten sein. All diese Aspekte werden von dem in dieser Arbeit präsentierten neuen Robotersystem abgedeckt.In biotechnolgical laboratories, the quality of the typically pharmaceutical product is a literally life-important goal. Historically, the quality of the cell cultivations was ensured by on-line measurements of physical process parameters like pH and pO2 only. Biological parameters like cell density and viability were only measured off-line, because the necessary sample management involves highly complicated manipulations and analyses and could therefore not be automated. Various automated devices to assist a laboratory technician do exist, but so far no system to automate the entire sample management. In this work a novel type of service robot consisting of a robot arm mounted on a mobile platform is presented that closes this gap. This robot has to master a multitude of problems: It must be able to locate its position in the laboratory (localisation), it must be able to find a collision-free path to the involved devices (path planning with obstacle avoidance), it must not endanger humans or damage laboratory equipment while moving (collision avoidance), it must be able to recognize the devices to be manipulated and measure their precise position (computer vision), it must be able to manipulate them (arm control), it must be able to grasp objects (gripper and fingers) and it must be able to handle them with compliance in order to not damage them (force control). It must be autonomous in order to only require the least possible amount of user intervention, and yet controllable by a laboratory control program in order to allow intervention. Finally, it must be easily maintainable by non-expert personell. All these aspects are covered by the novel robot system presented in this thesis

A memetic approach to the inverse kinematics problem for robotic applications

The inverse kinematics problem of an articulated robot system refers to computing the joint configuration that places the end-effector at a given position and orientation. To overcome the numerical instability of the Jacobian-based algorithms around singular joint configurations, the inverse kinematics is formulated as a constrained minimization problem in the configuration space of the robot. In previous works this problem has been solved for redundant and non-redundant robots using evolutionary-based algorithms. However, despite the flexibility and accuracy of the direct search approach of evolutionary algorithms, these algorithms are not suitable for most robot applications given their low convergence speed rate and the high computational cost of their population-based approach. In this thesis, we propose a memetic variant of the Differential Evolution (DE) algorithm to increase its convergence speed on the kinematics inversion problem of articulated robot systems. With the aim to yield an efficient trade-off between exploration and exploitation of the search space, the memetic approach combines the global search scheme of the standard DE with an independent local search mechanisms, called discarding. The proposed scheme is tested on a simulation environment for different benchmark serial robot manipulators and anthropomorphic robot hands. Results show that the memetic differential evolution is able to find solutions with high accuracy in less generations than the original DE. -----------------------------------------------------------La cinemática inversa de los robots manipuladores se refiere al problema de calcular las coordenadas articulares del robot a partir de coordenadas conocidas de posición y orientación de su extremo libre. Para evitar la inestabilidad numérica de los métodos basados en la inversa de la matriz Jacobiana en la vecindad de configuraciones singulares, el problema de cinemática inversa es definido en el espacio de configuraciones del robot manipulador como un problema de optimización con restricciones. Este problema de optimización ha sido previamente resuelto con métodos evolutivos para robots manipuladores, redundantes y no redundantes, obteniéndose buenos resultados; sin embargo, estos métodos exhiben una baja velocidad de convergencia no adecuada para aplicaciones robóticas. Para incrementar la velocidad de convergencia de estos algoritmos, se propone un método memético de evolución differencial. El enfoque de búsqueda directa propuesto combina el esquema estándar de evolución diferencial con un mecanismo independiente de refinamiento local, llamado discarding o descarte. El desempeño del método propuesto es evaluado en un entorno de simulación para diferentes robot manipuladores y manos robóticas antropomórficas. Los resultados obtenidos muestran una importante mejora en precisión y velocidad de convergencia en comparación del método DE original.Programa en Ingeniería Eléctrica, Electrónica y AutomáticaPresidente: Pedro M. Urbano de Almeida Lima; Vocal: Cecilia Elisabet García Cena; Secretario: Mohamed Abderrahim Fichouch

On the Application of Mechanical Vibration in Robotics-Assisted Soft Tissue Intervention

Mechanical vibration as a way of transmitting energy has been an interesting subject to study. While cyclic oscillation is usually associated with fatigue effect, and hence a detrimental factor in failure of structures and machineries, by controlled transmission of vibration, energy can be transferred from the source to the target. In this thesis, the application of such mechanical vibration in a few surgical procedures is demonstrated. Three challenges associated with lung cancer diagnosis and treatment are chosen for this purpose, namely, Motion Compensation, tumor targeting in lung Needle Insertion and Soft Tissue Dissection: A robotic solution is proposed for compensating for the undesirable oscillatory motion of soft tissue (caused by heart beat and respiration) during needle insertion in the lung. An impedance control strategy based on a mechanical vibratory system is implemented to minimize the tissue deformation during needle insertion. A prototype was built to evaluate the proposed approach using: 1) two Mitsubishi PA10-7C robots, one for manipulating the macro part and the other for mimicking the tissue motion, 2) one motorized linear stage to handle the micro part, and 3) a Phantom Omni haptic device for remote manipulation. Experimental results are given to demonstrate the performance of the motion compensation system. A vibration-assisted needle insertion technique has been proposed in order to reduce needle–tissue friction. The LuGre friction model is employed as a basis for the study and the model is extended and analyzed to include the impact of high-frequency vibration on translational friction. Experiments are conducted to evaluate the role of insertion speed as well as vibration frequency on frictional effects. In the experiments conducted, an 18 GA brachytherapy needle was vibrated and inserted into an ex-vivo soft tissue sample using a pair of amplified piezoelectric actuators. Analysis demonstrates that the translational friction can be reduced by introducing a vibratory low-amplitude motion onto a regular insertion profile, which is usually performed at a constant rate. A robotics-assisted articulating ultrasonic surgical scalpel for minimally invasive soft tissue cutting and coagulation is designed and developed. For this purpose, the optimal design of a Langevin transducer with stepped horn profile is presented for internal-body applications. The modeling, optimization and design of the ultrasonic scalpel are performed through equivalent circuit theory and verified by finite element analysis. Moreover, a novel surgical wrist, compatible with the da Vinci® surgical system, with decoupled two degrees-of-freedom (DOFs) is developed that eliminates the strain of pulling cables and electrical wires. The developed instrument is then driven using the dVRK (da Vinci® research kit) and the Classic da Vinci® surgical system

Modeling, Analysis, and Control of a Mobile Robot for \u3ci\u3eIn Vivo\u3c/i\u3e Fluoroscopy of Human Joints during Natural Movements

In this dissertation, the modeling, analysis and control of a multi-degree of freedom (mdof) robotic fluoroscope was investigated. A prototype robotic fluoroscope exists, and consists of a 3 dof mobile platform with two 2 dof Cartesian manipulators mounted symmetrically on opposite sides of the platform. One Cartesian manipulator positions the x-ray generator and the other Cartesian manipulator positions the x-ray imaging device. The robotic fluoroscope is used to x-ray skeletal joints of interest of human subjects performing natural movement activities. In order to collect the data, the Cartesian manipulators must keep the x-ray generation and imaging devices accurately aligned while dynamically tracking the desired skeletal joint of interest. In addition to the joint tracking, this also requires the robotic platform to move along with the subject, allowing the manipulators to operate within their ranges of motion. A comprehensive dynamic model of the robotic fluoroscope prototype was created, incorporating the dynamic coupling of the system. Empirical data collected from an RGB-D camera were used to create a human kinematic model that can be used to simulate the joint of interest target dynamics. This model was incorporated into a computer simulation that was validated by comparing the simulation results with actual prototype experiments using the same human kinematic model inputs. The computer simulation was used in a comprehensive dynamic analysis of the prototype and in the development and evaluation of sensing, control, and signal processing approaches that optimize the subject and joint tracking performance characteristics. The modeling and simulation results were used to develop real-time control strategies, including decoupling techniques that reduce tracking error on the prototype. For a normal walking activity, the joint tracking error was less than 20 mm, and the subject tracking error was less than 140 mm

Visual Servoing in Robotics

Visual servoing is a well-known approach to guide robots using visual information. Image processing, robotics, and control theory are combined in order to control the motion of a robot depending on the visual information extracted from the images captured by one or several cameras. With respect to vision issues, a number of issues are currently being addressed by ongoing research, such as the use of different types of image features (or different types of cameras such as RGBD cameras), image processing at high velocity, and convergence properties. As shown in this book, the use of new control schemes allows the system to behave more robustly, efficiently, or compliantly, with fewer delays. Related issues such as optimal and robust approaches, direct control, path tracking, or sensor fusion are also addressed. Additionally, we can currently find visual servoing systems being applied in a number of different domains. This book considers various aspects of visual servoing systems, such as the design of new strategies for their application to parallel robots, mobile manipulators, teleoperation, and the application of this type of control system in new areas

Cable-driven parallel mechanisms for minimally invasive robotic surgery

Minimally invasive surgery (MIS) has revolutionised surgery by providing faster recovery times, less post-operative complications, improved cosmesis and reduced pain for the patient. Surgical robotics are used to further decrease the invasiveness of procedures, by using yet smaller and fewer incisions or using natural orifices as entry point. However, many robotic systems still suffer from technical challenges such as sufficient instrument dexterity and payloads, leading to limited adoption in clinical practice. Cable-driven parallel mechanisms (CDPMs) have unique properties, which can be used to overcome existing challenges in surgical robotics. These beneficial properties include high end-effector payloads, efficient force transmission and a large configurable instrument workspace. However, the use of CDPMs in MIS is largely unexplored. This research presents the first structured exploration of CDPMs for MIS and demonstrates the potential of this type of mechanism through the development of multiple prototypes: the ESD CYCLOPS, CDAQS, SIMPLE, neuroCYCLOPS and microCYCLOPS. One key challenge for MIS is the access method used to introduce CDPMs into the body. Three different access methods are presented by the prototypes. By focusing on the minimally invasive access method in which CDPMs are introduced into the body, the thesis provides a framework, which can be used by researchers, engineers and clinicians to identify future opportunities of CDPMs in MIS. Additionally, through user studies and pre-clinical studies, these prototypes demonstrate that this type of mechanism has several key advantages for surgical applications in which haptic feedback, safe automation or a high payload are required. These advantages, combined with the different access methods, demonstrate that CDPMs can have a key role in the advancement of MIS technology.Open Acces

Contemporary Robotics

This book book is a collection of 18 chapters written by internationally recognized experts and well-known professionals of the field. Chapters contribute to diverse facets of contemporary robotics and autonomous systems. The volume is organized in four thematic parts according to the main subjects, regarding the recent advances in the contemporary robotics. The first thematic topics of the book are devoted to the theoretical issues. This includes development of algorithms for automatic trajectory generation using redudancy resolution scheme, intelligent algorithms for robotic grasping, modelling approach for reactive mode handling of flexible manufacturing and design of an advanced controller for robot manipulators. The second part of the book deals with different aspects of robot calibration and sensing. This includes a geometric and treshold calibration of a multiple robotic line-vision system, robot-based inline 2D/3D quality monitoring using picture-giving and laser triangulation, and a study on prospective polymer composite materials for flexible tactile sensors. The third part addresses issues of mobile robots and multi-agent systems, including SLAM of mobile robots based on fusion of odometry and visual data, configuration of a localization system by a team of mobile robots, development of generic real-time motion controller for differential mobile robots, control of fuel cells of mobile robots, modelling of omni-directional wheeled-based robots, building of hunter- hybrid tracking environment, as well as design of a cooperative control in distributed population-based multi-agent approach. The fourth part presents recent approaches and results in humanoid and bioinspirative robotics. It deals with design of adaptive control of anthropomorphic biped gait, building of dynamic-based simulation for humanoid robot walking, building controller for perceptual motor control dynamics of humans and biomimetic approach to control mechatronic structure using smart materials