Reconfigurable Reflectarrays and Array Lenses for Dynamic Antenna Beam Control: A Review

Advances in reflectarrays and array lenses with electronic beam-forming capabilities are enabling a host of new possibilities for these high-performance, low-cost antenna architectures. This paper reviews enabling technologies and topologies of reconfigurable reflectarray and array lens designs, and surveys a range of experimental implementations and achievements that have been made in this area in recent years. The paper describes the fundamental design approaches employed in realizing reconfigurable designs, and explores advanced capabilities of these nascent architectures, such as multi-band operation, polarization manipulation, frequency agility, and amplification. Finally, the paper concludes by discussing future challenges and possibilities for these antennas.Comment: 16 pages, 12 figure

Initial synchronisation of wideband and UWB direct sequence systems: single- and multiple-antenna aided solutions

This survey guides the reader through the open literature on the principle of initial synchronisation in single-antenna-assisted single- and multi-carrier Code Division Multiple Access (CDMA) as well as Direct Sequence-Ultra WideBand (DS-UWB) systems, with special emphasis on the DownLink (DL). There is a paucity of up-to-date surveys and review articles on initial synchronization solutions for MIMO-aided and cooperative systems - even though there is a plethora of papers on both MIMOs and on cooperative systems, which assume perfect synchronization. Hence this paper aims to ?ll the related gap in the literature

Light trapping in ultrathin plasmonic solar cells

We report on the design, fabrication, and measurement of ultrathin film a-Si:H solar cells with nanostructured plasmonic back contacts, which demonstrate enhanced short circuit current densities compared to cells having flat or randomly textured back contacts. The primary photocurrent enhancement occurs in the spectral range from 550 nm to 800 nm. We use angle-resolved photocurrent spectroscopy to confirm that the enhanced absorption is due to coupling to guided modes supported by the cell. Full-field electromagnetic simulation of the absorption in the active a-Si:H layer agrees well with the experimental results. Furthermore, the nanopatterns were fabricated via an inexpensive, scalable, and precise nanopatterning method. These results should guide design of optimized, non-random nanostructured back reflectors for thin film solar cells

Modelling and Optimisation of Single Junction Strain Balanced Quantum Well Solar Cells

In an attempt to find the optimum number of wells for maximum conversion efficiency a pair of otherwise identical strain balanced samples, one containing 50 wells and the other 65 wells have been characterised. The 65 well sample is found to possess a lower predicted efficiency than the 50 well sample, suggesting that the optimum well number lies between these values. Devices grown using tertiary butyl arsine (TBAs) are found to possess comparable conversion efficiencies to the control cells grown using arsine and slightly superior dark IV characteristics, indicating that TBAs may be substituted for arsine without loss of device efficiency and may even be beneficial to cell performance. Several fundamental refinements to the existing quantum efficiency model of are explored. Firstly, expressions for the strained band gaps are derived. A value for the conduction band offset is . determined using the difference in energy between the heavy and light hole exciton peaks in low temperature photo current scans and found to be 0.55??0.03. The magnitude of the el-hhl exciton binding energy is also estimated from these scans and found to be in excellent agreement with the value obtained from a simple, parameterized expression for the exciton binding energy. Finally, an absolute calculation for the absorption coefficient is incorporated into the quantum efficiency model and values for the heavy and light hole in-planes masses are obtained. The model is found to underestimate the level of absorption in the intrinsic region by an amount consistent with estimates of the magnitude of the reflection from the back surface. The conversion efficiency of a sample predicted using SOL is compared to an independently obtained value. Good agreement is observed between the two results (25.3% and 25.7% for 317 suns AM1.5D). Additionally, an optimum structure for illumination by the AM1.5D spectrum was found to be a 120A well ofIno.lGaAs.Imperial Users onl

Progress towards an accurate determination of the Boltzmann constant by Doppler spectroscopy

In this paper, we present significant progress performed on an experiment dedicated to the determination of the Boltzmann constant, k, by accurately measuring the Doppler absorption profile of a line in a gas of ammonia at thermal equilibrium. This optical method based on the first principles of statistical mechanics is an alternative to the acoustical method which has led to the unique determination of k published by the CODATA with a relative accuracy of 1.7 ppm. We report on the first measurement of the Boltzmann constant by laser spectroscopy with a statistical uncertainty below 10 ppm, more specifically 6.4 ppm. This progress results from improvements in the detection method and in the statistical treatment of the data. In addition, we have recorded the hyperfine structure of the probed saQ(6,3) rovibrational line of ammonia by saturation spectroscopy and thus determine very precisely the induced 4.36 (2) ppm broadening of the absorption linewidth. We also show that, in our well chosen experimental conditions, saturation effects have a negligible impact on the linewidth. Finally, we draw the route to future developments for an absolute determination of with an accuracy of a few ppm.Comment: 22 pages, 11 figure