Calculation of supersonic flows at large distances from slender lifting bodies

Solving exact gas dynamic equations for supersonic flows far from axis of slender lifting bodie

Aerodynamic preliminary analysis system 2. Part 2: User's manual

An aerodynamic analysis system based on potential theory at subsonic and/or supersonic speeds and impact type finite element solutions at hypersonic conditions is described. Three dimensional configurations have multiple nonplanar surfaces of arbitrary planforms and bodies of noncircular contour may be analyzed. Static, rotary, and control longitudinal and lateral-directional characteristics may be generated. The analysis was implemented on a time sharing system in conjunction with an input tablet digitizer and an interactive graphics input/output display and editing terminal to maximize its responsiveness to the preliminary analysis. Computation times on an IBM 3081 are typically less than one minute of CPU/Mach number at subsonic, supersonic, or hypersonic speeds. This is a user manual for the computer programming

Aerodynamic configuration development of the highly maneuverable aircraft technology remotely piloted research vehicle

The aerodynamic development of the highly maneuverable aircraft technology remotely piloted research vehicle (HiMAT/RPRV) from the conceptual design to the final configuration is presented. The design integrates several advanced concepts to achieve a high degree of transonic maneuverability, and was keyed to sustained maneuverability goals while other fighter typical performance characteristics were maintained. When tests of the baseline configuration indicated deficiencies in the technology integration and design techniques, the vehicle was reconfigured to satisfy the subcritical and supersonic requirements. Drag-due-to-lift levels only 5 percent higher than the optimum were obtained for the wind tunnel model at a lift coefficient of 1 for Mach numbers of up to 0.8. The transonic drag rise was progressively lowered with the application of nonlinear potential flow analyses coupled with experimental data

Separated flow over bodies of revolution using an unsteady discrete-vorticity cross wake. Part 1: Theory and application

A method is developed to determine the flow field of a body of revolution in separated flow. The technique employed is the use of the computer to integrate various solutions and solution properties of the sub-flow fields which made up the entire flow field without resorting to a finite difference solution to the complete Navier-Stokes equations. The technique entails the use of the unsteady cross flow analogy and a new solution to the required two-dimensional unsteady separated flow problem based upon an unsteady, discrete-vorticity wake. Data for the forces and moments on aerodynamic bodies at low speeds and high angle of attack (outside the range of linear inviscid theories) such that the flow is substantially separated are produced which compare well with experimental data. In addition, three dimensional steady separation regions and wake vortex patterns are determined

Control of vortical separation on conical bodies

In a variety of aeronautical applications, the flow around conical bodies at incidence is of interest. Such applications include, but are not limited to, highly maneuverable aircraft with delta wings, the aerospace plane and nose portions of spike inlets. The theoretical model used has three parts. First, the single line vortex model is used within the framework of slender body theory, to compute the outer inviscid field for specified separation lines. Next, the three dimensional boundary layer is represented by a momentum equation for the cross flow, analogous to that for a plane boundary layer; a von Karman Pohlhausen approximation is applied to solve this equation. The cross flow separation for both laminar and turbulent layers is determined by matching the pressure at the upper and lower separation points. This iterative procedure yields a unique solution for the separation lines and consequently for the position of the vortices and the vortex lift on the body. Lastly, control of separation is achieved by blowing tangentially from a slot located along a cone generator. It is found that for very small blowing coefficients, the separation can be postponed or suppressedy completely

Aeronautical Engineering: A continuing bibliography, supplement 120

This bibliography contains abstracts for 297 reports, articles, and other documents introduced into the NASA scientific and technical information system in February 1980

The compression chord capacity model for the shear design and assessment of reinforced and prestressed concrete beams

This is the accepted version of the following article: [Cladera, A., Marí, A., Bairán, J. M., Ribas, C., Oller, E. and Duarte, N. (2016), The compression chord capacity model for the shear design and assessment of reinforced and prestressed concrete beams. Structural Concrete, 17: 1017–1032. doi:10.1002/suco.201500214], which has been published in final form at http://onlinelibrary.wiley.com/doi/10.1002/suco.201500214/fullA simplified mechanical model is presented for the shear strength prediction of reinforced and prestressed concrete members with and without transverse reinforcement, with I, T or rectangular cross-section. The model, derived with further simplifications from a previous one developed by the authors, incorporates the contributions of the concrete compression chord, the cracked web, the dowel action and the shear reinforcement in a compact formulation. The mechanical character of the model provides valuable information about the physics of the problem and incorporates the most relevant parameters governing the shear strength of structural concrete members. The predictions of the model fit very well the experimental results collected in the ACI-DAfStb databases of shear tests on slender reinforced and prestressed concrete beams with and without stirrups. Due to this fact and the simplicity of the derived equations it may become a very useful tool for structural design and assessment in engineering practice.Peer ReviewedPostprint (author's final draft

A three dimensional vortex wake model for missiles at high angles on attack

A three dimensional model for the steady flow past missile and aircraft nose shaped bodies is presented based on augmenting a potential solution with a wake composed of vortex filaments. The vortex positions are determined by the requirement that they, in some sense, align with the flow. The aerodynamic loads on the body are compared with experimental values and used to evaluate the model. The vortex positions compare well with flow visualization results for slender bodies at high angles of attack. The approximations in the wake near the body cause peaks in the force distributions more severe than in the measured values. For given vortex strengths and body attachment points multiple steady vortex positions were not found

A computational system for aerodynamic design and analysis of supersonic aircraft. Part 1: General description and theoretical development

An integrated system of computer programs was developed for the design and analysis of supersonic configurations. The system uses linearized theory methods for the calculation of surface pressures and supersonic area rule concepts in combination with linearized theory for calculation of aerodynamic force coefficients. Interactive graphics are optional at the user's request. Schematics of the program structure and the individual overlays and subroutines are described