Development of reliability methodology for systems engineering. Volume II - Application - Design reliability analysis of a 250 volt-ampere static inverter Final report

Design stage reliability analysis application to static inverte

Modeling and analysis of power processing systems: Feasibility investigation and formulation of a methodology

A review is given of future power processing systems planned for the next 20 years, and the state-of-the-art of power processing design modeling and analysis techniques used to optimize power processing systems. A methodology of modeling and analysis of power processing equipment and systems has been formulated to fulfill future tradeoff studies and optimization requirements. Computer techniques were applied to simulate power processor performance and to optimize the design of power processing equipment. A program plan to systematically develop and apply the tools for power processing systems modeling and analysis is presented so that meaningful results can be obtained each year to aid the power processing system engineer and power processing equipment circuit designers in their conceptual and detail design and analysis tasks

Class-E rectifiers and power converters: the operation of the class-E topology as a power amplifier and a rectifier with very high conversion efficiencies

In the late 70’s, the interest in reducing the value and size of reactive components moved power supply specialists to operate dc-to-dc converters at hundreds of kHz or even MHz frequencies. Passive energy storage (mainly magnetics) dominates the size of power electronics, limiting also its cost, reliability and dynamic response. Motivated by miniaturization and improved control bandwidth, they had to face the frequency-dependent turn-on and turn-off losses associated with the use of rectangular waveforms in the hard-switched topologies of that time. Similar to approaches for RF/microwave power amplifiers (PAs), the introduction of resonant circuits allowed shaping either a sinusoidal voltage or current, with parasitic reactive elements absorbed by the topology in the neighborhood of the switching frequency. The resulting resonant power converters, obtained by cascading a dc-to-ac resonant inverter with a high-frequency ac-to-dc rectifier, first transform the dc input power into controlled ac power, and then convert it back into the desired dc output [1]. This paper provides some historic notes on the operation of the class-E topology, introduced worldwide to the RF/microwave community by Nathan O. Sokal [2], as a power inverter and as a rectifier, with very high conversion efficiencies up to microwave frequencies. Recent research advances and implementations of class-E rectifiers and dc-to-dc converters at UHF and beyond are included. Offering competitive performance in terms of efficiency for RF power recovery, together with a wide bandwidth for low-loss power conversion, their potential for some modern applications is highlighted.The authors would like to acknowledge support in part by the Spanish Ministry of Economy, Industry and Competitiveness (MINECO) through TEC2014-58341-C4-1-R and TEC2017-83343-C4-1-R projects, co-funded with FEDER, and in part by Lockheed Martin Endowed Chair at the University of Colorado

Grid-Forming Converter Control Method to Improve DC-Link Stability in Inverter-Based AC Grids

As renewable energy sources with power-electronic interfaces become functionally and economically viable alternatives to bulk synchronous generators, it becomes vital to understand the behavior of these inverter-interfaced sources in ac grids devoid of any synchronous generation, i.e. inverter-based grids. In these types of grids, the inverters need to operate in parallel in grid-forming mode to regulate and synchronize their output voltage while also delivering the power required by the loads. It is common practice, therefore, to mimic the parallel operation control of the very synchronous generators that these inverter-based sources are meant to replace. This practice, however, is based on impractical assumptions and completely disregards the key differences between synchronous machines and power electronic inverters, as well as the dynamics of the dc source connected to the inverter. This dissertation aims to highlight the shortcomings of conventional controllers and derive an improved grid-forming inverter controller that is effective in parallel ac operation without sacrificing dc-link stability. This dissertation begins with a basis for understanding the control concepts used by grid-forming inverters in ac grids and exploring where existing ideas and methods are lacking in terms of efficient and stable inverter control. The knowledge gained from the literature survey is used to derive the requirements for a grid-forming control method that is appropriate for inverter-based ac grids. This is followed by a review and comparative analysis of the performance of five commonly used control techniques for grid-forming inverters, which reveal that nested loop controllers can have a destabilizing effect under changing grid conditions. This observation is further explored through an impedance-based stability analysis of single-loop and nested-loop controllers in grid-forming inverters, followed by a review of impedance-based analysis methods that can be used to assess the control design for grid-forming inverters. An improved grid-forming inverter controller is proposed with a demonstrated ability to achieve both dc-link and ac output stability with proportional power-sharing. This dissertation ends with a summary of the efforts and contributions as well as ideas for future applications of the proposed controller

RF Power Transfer, Energy Harvesting, and Power Management Strategies

Energy harvesting is the way to capture green energy. This can be thought of as a recycling process where energy is converted from one form (here, non-electrical) to another (here, electrical). This is done on the large energy scale as well as low energy scale. The former can enable sustainable operation of facilities, while the latter can have a significant impact on the problems of energy constrained portable applications. Different energy sources can be complementary to one another and combining multiple-source is of great importance. In particular, RF energy harvesting is a natural choice for the portable applications. There are many advantages, such as cordless operation and light-weight. Moreover, the needed infra-structure can possibly be incorporated with wearable and portable devices. RF energy harvesting is an enabling key player for Internet of Things technology. The RF energy harvesting systems consist of external antennas, LC matching networks, RF rectifiers for ac to dc conversion, and sometimes power management. Moreover, combining different energy harvesting sources is essential for robustness and sustainability. Wireless power transfer has recently been applied for battery charging of portable devices. This charging process impacts the daily experience of every human who uses electronic applications. Instead of having many types of cumbersome cords and many different standards while the users are responsible to connect periodically to ac outlets, the new approach is to have the transmitters ready in the near region and can transfer power wirelessly to the devices whenever needed. Wireless power transfer consists of a dc to ac conversion transmitter, coupled inductors between transmitter and receiver, and an ac to dc conversion receiver. Alternative far field operation is still tested for health issues. So, the focus in this study is on near field. The goals of this study are to investigate the possibilities of RF energy harvesting from various sources in the far field, dc energy combining, wireless power transfer in the near field, the underlying power management strategies, and the integration on silicon. This integration is the ultimate goal for cheap solutions to enable the technology for broader use. All systems were designed, implemented and tested to demonstrate proof-of concept prototypes

The ac power system testbed

The object of this program was to design, build, test, and deliver a high frequency (20 kHz) Power System Testbed which would electrically approximate a single, separable power channel of an IOC Space Station. That program is described, including the technical background, and the results are discussed showing that the major assumptions about the characteristics of this class of hardware (size, mass, efficiency, control, etc.) were substantially correct. This testbed equipment was completed and delivered and is being operated as part of the Space Station Power System Test Facility

Optimization study of high power static inverters and converters Final report

Optimization study and basic performance characteristics for conceptual designs for high power static inverter

Measurements, Models, Systems and Design

531 s.

Analysis of electric propulsion electrical power conditioning component technology. Volume 1 - Data bank Final report

Analysis of electric propulsion electric power conditioning component technology - data revie