166 research outputs found
Experimental Validation of the Kinematic Design of 3PRS Compliant Parallel Mechanisms
In this paper, a procedure for the kinematic design of a 3-PRS compliant parallel manipulator of 3 degrees of freedom is proposed. First, under the assumption of small displacements, the solid body kinematics of the 3-PRS has been studied, performing a comprehensive analysis of the inverse and forward kinematic problem, and calculating the rotations that the revolute and spherical flexure joints must perform. Then, after defining some design requirements and therefore the necessary displacements to fulfill, a design process based on the finite element calculations has been stablished, giving the necessary guidelines to reach the optimal solution on a 3-PRS compliant mechanism. Also, a prototype has been tested, using a coordinate measuring machine to verify its dimensions and the resulting displacements in the end effector and the actuated joints. Finally, those measurements have been compared with the FEM and the rigid body kinematics predictions, contrasting the validity of those two modelling approaches for the kinematic design of compliant mechanisms.The authors of this paper wish to acknowledge the financial support received from the Spanish Government via the Ministerio de Educación y Ciencia (Project DPI2011-22955) and Ministerio de Economía y Competitividad (Project DPI2015-64450-R), the ERDF of the European Union, the Government of the Basque Country (Project GIC07/78, IT445-10 and SAIOTEK 2013 SAI13/245, SPC13UN011), and the University of the Basque Country (Project EHUA13/30 and Zabalduz-2012). Thanks are also addressed to Dr. Jorge Presa and Alfonso Urzainki from Egile Corporation XXI for their valuable contributions
An Overview of Kinematic and Calibration Models Using Internal/External Sensors or Constraints to Improve the Behavior of Spatial Parallel Mechanisms
This paper presents an overview of the literature on kinematic and calibration models of parallel mechanisms, the influence of sensors in the mechanism accuracy and parallel mechanisms used as sensors. The most relevant classifications to obtain and solve kinematic models and to identify geometric and non-geometric parameters in the calibration of parallel robots are discussed, examining the advantages and disadvantages of each method, presenting new trends and identifying unsolved problems. This overview tries to answer and show the solutions developed by the most up-to-date research to some of the most frequent questions that appear in the modelling of a parallel mechanism, such as how to measure, the number of sensors and necessary configurations, the type and influence of errors or the number of necessary parameters
Affordable flexible hybrid manipulator for miniaturised product assembly
Miniaturised assembly systems are capable of assembling parts of a few millimetres in size with an accuracy of a few micrometres. Reducing the size and the cost of such a system while increasing its flexibility and accuracy is a challenging issue. The introduction of hybrid manipulation, also called coarse/fine manipulation, within an assembly system is the solution investigated in this thesis. A micro-motion stage (MMS) is designed to be used as the fine positioning mechanism of the hybrid assembly system. MMSs often integrate compliant micro-motion stages (CMMSs) to achieve higher performances than the conventional MMSs. CMMSs are mechanisms that transmit an output force and displacement through the deformation of their structure. Although widely studied, the design and modelling techniques of these mechanisms still need to be improved and simplified. Firstly, the linear modelling of CMMSs is evaluated and two polymer prototypes are fabricated and characterised. It is found that polymer based designs have a low fabrication cost but not suitable for construction of a micro-assembly system. A simplified nonlinear model is then derived and integrated within an analytical model, allowing for the full characterisation of the CMMS in terms of stiffness and range of motion. An aluminium CMMS is fabricated based on the optimisation results from the analytical model and is integrated within an MMS. The MMS is controlled using dual-range positioning to achieve a low-cost positioning accuracy better than 2µm within a workspace of 4.4×4.4mm2. Finally, a hybrid manipulator is designed to assemble mobile-phone cameras and sensors automatically. A conventional robot manipulator is used to pick and place the parts in coarse mode while the aluminium CMMS based MMS is used for fine alignment of the parts. A high-resolution vision system is used to locate the parts on the substrate and to measure the relative position of the manipulator above MMS using a calibration grid with square patterns. The overall placement accuracy of the assembly system is ±24µm at 3σ and can reach 2µm, for a total cost of less than £50k, thus demonstrating the suitability of hybrid manipulation for desktop-size miniaturised assembly systems. The precision of the existing system could be significantly improved by making the manipulator stiffer (i.e. preloaded bearings…) and adjustable to compensate for misalignment. Further improvement could also be made on the calibration of the vision system. The system could be either scaled up or down using the same architecture while adapting the controllers to the scale.Engineering and Physical Sciences Research Council (EPSRC
Recommended from our members
Development of a Robotic Positioning and Tracking System for a Research Laboratory
Measurement of residual stress using neutron or synchrotron diffraction relies on the accurate alignment of the sample in relation to the gauge volume of the instrument. Automatic sample alignment can be achieved using kinematic models of the positioning system provided the relevant kinematic parameters are known, or can be determined, to a suitable accuracy.
The main problem addressed in this thesis is improving the repeatability and accuracy of the sample positioning for the strain scanning, through the use of techniques from robotic calibration theory to generate kinematic models of both off-the-shelf and custom-built positioning systems. The approach is illustrated using a positioning system in use on the ENGIN-X instrument at the UK’s ISIS pulsed neutron source comprising a traditional XYZΩ table augmented with a triple axis manipulator. Accuracies better than 100microns were achieved for this compound system. Although discussed here in terms of sample positioning systems these methods are entirely applicable to other moving instrument components such as beam shaping jaws and detectors.
Several factors could lead to inaccurate positioning on a neutron or synchrotron diffractometer. It is therefore essential to validate the accuracy of positioning especially during experiments which require a high level of accuracy. In this thesis, a stereo camera system is developed to monitor the sample and other moving parts of the diffractometer. The camera metrology system is designed to measure the positions of retroreflective markers attached to any object that is being monitored. A fully automated camera calibration procedure is developed with an emphasis on accuracy. The potential accuracy of this system is demonstrated and problems that limit accuracy are discussed. It is anticipated that the camera system would be used to correct the positioning system when the error is minimal or notify the user of the error when it is significant
A SERIAL-PARALLEL HYBRID ROBOT FOR MACHINING OF COMPLEX SURFACES
Ph.DDOCTOR OF PHILOSOPH
Erosion and dilation of edges in dimensional X-ray computed tomography images
Dimensional X-ray Computed Tomography (CT) is a rapidly expanding field of research due to the numerous advantages this technique offers over conventional measurement technologies, most notably, the ability to measure internal features of a component. Tactile and optical Coordinate Measurement Machines (CMM), currently used in the manufacturing production industry, record points on the external surface of a workpiece by measuring the contact point of a physical probe or the reflection of projected light. X-ray CT has the ability to capture full volumetric data, since X-rays are transmitted through the entire object, revealing features which are otherwise invisible. Over the past five years, interest in this field has grown in the UK, with an increasing number of organisations in industry and research having access to X-ray CT machines and the wide range of manufacturers, offering new systems specifically designed for dimensional metrology applications.Despite this, the complexity of data acquisition required for dimensional measurement using X-ray CT has made it difficult to estimate the measurement uncertainty. This has hindered the generation of standards and full-scale adoption of this technique in industry. Due to the nature of X-ray imaging, a number of non-linear influence factors exist which have the potential to cause dimensional measurement error. These influences must be better understood to reduce and ideally, compensate error.In this doctoral thesis, the effects of the influence factors associated with CT data acquisition are studied, specifically, beam hardening and a finite X-ray source size. The effects these have on the quality of X-ray CT data are well understood; typically degrading the achievable contrast and spatial resolution of the CT image. However, the effects on dimensional measurement are less well understood due to the complexity of their interactions before reconstruction of the final image. These influences are modelled in a simulated CT acquisition to quantify any systematic effects on determination of edges in the CT image. The results are then validated by experimentally replicating the simulation set-up.In this work, it is found that beam hardening and a finite source diameter can lead to systematic errors in the edge position within the CT image. Beam hardening generally leads to dilation of the edge; where the edge position moves in the direction of the surface vector. In contrast, a finite source diameter can lead to erosion of the edge; where the edge position moves in an opposing direction to the surface vector.</div
Robot Manipulators
Robot manipulators are developing more in the direction of industrial robots than of human workers. Recently, the applications of robot manipulators are spreading their focus, for example Da Vinci as a medical robot, ASIMO as a humanoid robot and so on. There are many research topics within the field of robot manipulators, e.g. motion planning, cooperation with a human, and fusion with external sensors like vision, haptic and force, etc. Moreover, these include both technical problems in the industry and theoretical problems in the academic fields. This book is a collection of papers presenting the latest research issues from around the world
- …