6,850 research outputs found
A Single-Stage LED Driver Based on ZCDS Class-E Current-Driven Rectifier as a PFC for Street-Lighting Applications
This paper presents a light-emitting diode (LED) driver for street-lighting applications that uses a resonant rectifier as a power-factor corrector (PFC). The PFC semistage is based on a zero-current and zero-derivative-switching (ZCDS) Class-E current-driven rectifier, and the LED driver semistage is based on a zero-voltage-switching (ZVS) Class-D LLC resonant converter that is integrated into a single-stage topology. To increase the conduction angle of the bridge-rectifier diodes current and to decrease the current harmonics that are injected in the utility line, the ZCDS Class-E rectifier is placed between the bridge-rectifier and a dc-link capacitor. The ZCDS Class-E rectifieris driven by a high-frequency current source, which is obtained from a square-wave output voltage of the ZVS Class-D LLC resonant converter using a matching network. Additionally, the proposed converter has a soft-switching characteristic that reduces switching losses and switching noise. A prototype for a 150-W LED street light has been developed and tested to evaluate the performance of the proposed approach. The proposed LED driver had a high efficiency (>91%), a high PF (>0.99), and a low total harmonic distortion (THD i <; 8%) under variation of the utility-line input voltage from 180 to 250 V rms . These experimental results demonstrate the feasibility of the proposed LED scheme
State-space averaged modeling and transfer function derivation of DC-DC boost converter for high-brightness led lighting applications
This paper presents dynamic analysis of a boost type DC-DC converter for high-brightness LED (HBLED) driving applications. The steady state operation in presence of all system parasitics has been discussed for continuous conduction mode (CCM). The state-space averaging, energy conservation principle and standard linearization are used to derive ac small signal control to inductor current open-loop transfer function of the converter. The derived transfer function can be further used in designing a robust feed-back control network for the system. In the end frequency and transient responses of the derived transfer function are obtained for a given set of component values, hence to provide a useful guide for control design engineers
A Class-E-Based Resonant AC-DC Converter With Inherent PFC Capability
This paper investigates the use of the class-E inverter for power factor correction (PFC) applications. Analytical and state-space models are derived showing the class-E inverter’s capability of achieving inherent PFC operation with a constant duty cycle. The inherent PFC operation limits the controller responsibility to the regulation of the output voltage, which is key for resonant converters with challenging control. A converter incorporating a diode bridge, a class-E inverter, and a class-D rectifier is presented for the PFC stage in single-phase offline converters. A prototype is designed to validate the analysis and presented design method. The prototype operates with zero-voltage switching (ZVS) across the load range and achieves up to 211 W of output power at an efficiency of 88%, with an inherent power factor of 0.99 and a total harmonic distortion (THD) of 8.8 %. Frequency modulation is used to achieve lower output power down to 25 W, with a power factor of 0.95, THD of 28 %, and an efficiency of 88 %
A flicker-free electrolytic capacitor-less AC-DC LED driver
published_or_final_versio
Generalized self-driven AC-DC synchronous rectification techniques for single- and multiphase systems
This paper extends the single-phase self-driven synchronous rectification (SDSR) technique to multiphase ac-dc systems. Power MOSFETs with either voltage- or current-sensing self-driven gate drives are used to replace the diodes in the rectifier circuits. The generalized methodology allows multiphase SDSRs to be designed to replace the multiphase diode rectifiers. Unlike the traditional SR that is designed for high-frequency power converters, the SDSR proposed here can be a direct replacement of the power diode bridges for both low- and high-frequency operations. The SDSR utilizes its output dc voltage to supply power to its control circuit. No start-up control is needed because the body diodes of the power MOSFETs provide the diode rectifier for the initial start-up stage. The generalized method is demonstrated in 2-kW one-phase and three-phase SDSRs for inductive, capacitive, and resistive loads. Power loss reduction in the range of 50%-69% has been achieved for the resistive load. © 2009 IEEE.published_or_final_versio
Design and Control of Power Converters 2019
In this book, 20 papers focused on different fields of power electronics are gathered. Approximately half of the papers are focused on different control issues and techniques, ranging from the computer-aided design of digital compensators to more specific approaches such as fuzzy or sliding control techniques. The rest of the papers are focused on the design of novel topologies. The fields in which these controls and topologies are applied are varied: MMCs, photovoltaic systems, supercapacitors and traction systems, LEDs, wireless power transfer, etc
On supplying LEDs from very low dc voltages with high frequency AC-LED drivers
This work studies the driving of white Light Emitting Diodes (LEDs) from very low voltages in the range of 1.2 to 2 V. The proposed idea is based on replacing the standard Schottky diode used in conventional converter topologies (i.e., buck, buck-boost and boost) with an LED, while shortcutting the output of the converter. In this configuration, the LED works both as the load and as the rectifier diode of the converter, hence, switching the LED at high frequencies (i.e. > 100 kHz). Moreover, a thorough analytical study is carried out for the two topologies rendered in this work. Particularly emphasizing their static analysis and the obtaining of the boundaries between the different conduction modes. Finally, the idea is validated experimentally by means of the boost converter variation (i.e., DL//S AC-LED driver). The DL//S AC-LED driver has also been compared with a dc-dc boost converter showing a better luminous efficacy while disposing of the Schottky diode and the output capacitor. This analysis is carried out when connected to a Li-Ion battery using a simple control and integrated circuit for its development.This work has been supported by the Spanish Government under Project MINECO-17-DPI2016-75760-R and the Principality of Asturias under the grants “Severo Ochoa” BP14-142 and by the Project SV-PA-17-RIS3-4, and by European Regional Development Fund (ERDF) grants
Active input current shaper without an electrolytic capacitor for retrofit lamps applications
The evolution of solid-state lighting technology has transformed traditional solutions in lighting. High-brightness light-emitting diodes (HB-LEDs) have become very attractive light sources due to their excellent characteristics, namely high efficiency, a long lifetime, and low maintenance. It is evident that HB-LED drivers must be durable and efficient in order to enjoy these advantages. Moreover, to replace incandescent bulbs, the ac-to-dc HB-LED driver must be simple and have low size and comply with international regulations (i.e., injecting low-frequency harmonics into the mains supply). With the last modifications regarding low-power lighting equipment (i.e., < 25 W), the authors have traditionally focused their efforts on increasing efficiency by sacrificing sinusoidal input current, yet all their solutions obviate the suppression of the traditional electrolytic capacitor of ac-to-dc converters, highlighting that this is the price to pay for a simple and low-size solution. This paper, however, puts forward the design of a simple and low-size ac-to-dc HB-LED driver for retrofit lamps without an electrolytic capacitor in order to extend its lifetime. The solution proposed here derives from a well-known technique used in the past, the active input current shaper (AICS), but without an electrolytic capacitor in this case. If the electrolytic capacitor of an AICS is removed, then low-frequency ripple arises at its intermediate dc bus, adding some distortion in the line input current over the proper natural one of an AICS. However, this addition is slight in comparison to the proper natural distortion of AICSs. Moreover, the low-frequency ripple at the intermediate bus is not transferred to the output with the help of the rapid output dynamic response of the AICS, which prevents flicker. This paper presents a theoretical analysis that guarantees a compromise between compliance with international regulations and the use of capacitor technologies other than the electrolytic design. Finally, a 24-W experimental prototype has been built and tested to validate the theoretical results presented in this paper.This work was supported by the Spanish Ministry of Education and Science under Project MINECO-13-DPI2013-47176-C2-2-R, by the Government of the Principality of Asturias under Project FC-15-GRUPIN14-143, and by European Regional Development Fund grants
- …