LTE-verkon suorituskyvyn parantaminen CDMA2000:sta LTE:hen tehdyn muutoksen jälkeen

CDMA2000 technology has been widely used on 450 MHz band. Recently the equipment availability and improved performance offered by LTE has started driving the operators to migrate their networks from CDMA2000 to LTE. The migration may cause the network performance to be in suboptimal state. This thesis presents four methods to positively influence LTE network performance after CDMA2000 to LTE migration, especially on 450 MHz band. Furthermore, three of the four presented methods are evaluated in a live network. The measured three methods were cyclic prefix length, handover parameter optimization and uplink coordinated multipoint (CoMP) transmission. The objective was to determine the effectiveness of each method. The research methods included field measurements and network KPI collection. The results show that normal cyclic prefix length is enough for LTE450 although the cell radius may be up to 50km. Only special cases exist where cyclic prefix should be extended. Operators should consider solving such problems individually instead of widely implementing extended cyclic prefix. Handover parameter optimization turned out to be an important point of attention after CDMA2000 to LTE migration. It was observed that if the handover parameters are not concerned, significant amount of unnecessary handovers may happen. It was evaluated that about 50% of the handovers in the network were unnecessary in the initial situation. By adjusting the handover parameter values 47,28 % of the handovers per user were removed and no negative effects were detected. Coordinated multipoint transmission has been widely discussed to be an effective way to improve LTE network performance, especially at the cell edges. Many challenges must be overcome before it can be applied to downlink. Also, implementing it to function between cells in different eNBs involve challenges. Thus, only intra-site uplink CoMP transmission was tested. The results show that the performance improvements were significant at the cell edges as theory predicted.CDMA2000 teknologiaa on laajalti käytetty 450 MHz:n taajuusalueella. Viime aikoina LTE:n tarjoamat halvemmat laitteistot ja parempi suorituskyky ovat kannustaneet operaattoreita muuttamaan verkkoaan CDMA2000:sta LTE:hen. Kyseinen muutos saattaa johtaa epäoptimaaliseen tilaan verkon suorituskyvyn kannalta. Tämä työ esittelee neljä menetelmää, joilla voidaan positiivisesti vaikuttaa LTE-verkon suorituskykyyn CDMA2000:ste LTE:hen tehdyn muutoksen jälkeen erityisesti 450 MHz:n taajuusalueella. Kolmea näistä menetelmistä arvioidaan tuotantoverkossa. Nämä kolme menetelmää ovat suojavälin pituus, solunvaihtoparametrien optimointi ja ylälinkin koordinoitu monipistetiedonsiirto. Tavoite oli määrittää kunkin menetelmän vaikutus. Tutkimusmenetelmiin kuului kenttämittaukset ja verkon suorituskykymittareiden analyysi. Tutkimustulosten perusteella voidaan sanoa, että normaali suojaväli on riittävän pitkä LTE450:lle vaikka solujen säde on jopa 50km. Vain erikoistapauksissa tarvitaan pidennettyä suojaväliä. Operaattoreiden tulisi ratkaista tällaiset tapaukset yksilöllisesti sen sijaan, että koko verkossa käytettäisiin pidennettyä suojaväliä. Solunvaihtoparametrien optimointi osoittautui tärkeäksi huomion aiheeksi CDMA2000:sta LTE:hen tehdyn muutoksen jälkeen. Turhia solunvaihtoja saattaa tapahtua merkittäviä määriä, mikäli parametreihin ei kiinnitetä huomiota. Lähtötilanteessa noin 50 % testiverkon solunvaihdoista arvioitiin olevan turhia. Solunvaihtoparametreja muuttamalla 47,28 % solunvaihdoista per käyttäjä saatiin poistettua ilman, että mitään haittavaikutuksia olisi huomattu. Koordinoidun monipistetiedonsiirron on laajalti sanottu olevan tehokas tapa parantaa LTE-verkon suorituskykyä, etenkin solujen reunoilla. Monia haasteita pitää ratkaista, enne kuin sitä voidaan käyttää alalinkin tiedonsiirtoon. Lisäksi sen käyttöön eri tukiasemien solujen välillä liittyy haasteita. Tästä syystä monipistetiedonsiirtoa voitiin testata vain ylälinkin suuntaan ja vain yhden tukiaseman välisten solujen kesken. Tulokset osoittivat, että suorituskyky parani merkittävästi solun reunalla

5G New Radio for Terrestrial Broadcast: A Forward-Looking Approach for NR-MBMS

"© 2019 IEEE. Personal use of this material is permitted. Permissíon from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertisíng or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works."[EN] 3GPP LTE eMBMS release (Rel-) 14, also referred to as further evolved multimedia broadcast multicast service (FeMBMS) or enhanced TV (EnTV), is the first mobile broadband technology standard to incorporate a transmission mode designed to deliver terrestrial broadcast services from conventional high power high tower (HPHT) broadcast infrastructure. With respect to the physical layer, the main improvements in FeMBMS are the support of larger inter-site distance for single frequency networks (SFNs) and the ability to allocate 100% of a carrier's resources to the broadcast payload, with self-contained signaling in the downlink. From the system architecture perspective, a receive-only mode enables free-to-air (FTA) reception with no need for an uplink or SIM card, thus receiving content without user equipment registration with a network. These functionalities are only available in the LTE advanced pro specifications as 5G new radio (NR), standardized in 3GPP from Rel-15, has so far focused entirely on unicast. This paper outlines a physical layer design for NR-MBMS, a system derived, with minor modifications, from the 5G-NR specifications, and suitable for the transmission of linear TV and radio services in either single-cell or SFN operation. This paper evaluates the NR-MBMS proposition and compares it to LTE-based FeMBMS in terms of flexibility, performance, capacity, and coverage.This work was supported in part by the European Commission through the 5G-PPP Project 5G-Xcast (H2020-ICT-2016-2 call) under Grant 761498.Gimenez, JJ.; Carcel, JL.; Fuentes, M.; Garro, E.; Elliott, S.; Vargas, D.; Menzel, C.... (2019). 5G New Radio for Terrestrial Broadcast: A Forward-Looking Approach for NR-MBMS. IEEE Transactions on Broadcasting. 65(2):356-368. https://doi.org/10.1109/TBC.2019.291211735636865

Coordinated Multicast/Unicast Transmission on 5G: A Novel Approach for Linear Broadcasting

Linear broadcasting services, with a scheduled programming, constitute a paramount tel-ecommunication service for today’s society. Although the existing technology is mature, current linear broadcast systems have serious limitations when providing service to moving users or users placed in areas with complex orography and poor signal quality. To over-come these limitations, 3GPP 5G standard has included a work item to support 5G mul-ticast/broadcast services for future Release 17. This paper investigates the integration of point-to-point (unicast) communication with cellular multicast/broadcast on 5G technology to extend the current support of linear broadcasting services. This integration relies on the use mobile edge computing (MEC) at the 5G base station (gNB) to host a dynamic adap-tive streaming over HTTP (DASH) server that is coordinated with the multicast transmis-sion to complement the broadcast service. This approach join the reliability of point-to-point communications, with dedicated resources for each user, with the spectrum efficiency of multi-cast communications, where a set of users share common resources. The coopera-tion between those unicast and multicast schemes allows those users whose coverage is not good enough, to complete the linear broadcast flow through the point-to-point transmission via MEC. The benefits of such approach have been assessed with simulations in a realistic scenario that considers a vehicle moving across a sparsely populated region in southern Spain. Results reveals that throughput and bitrate playback (reproduction rate) are greatly improved when unicast/multicast integration is enabled since the number of stalling events is reduced significantly.This work has been partially supported by Radio Televisión Española through Impulsa Visión RTVE grant and by the Universidad de Málaga. We are grateful to Pere Vila, Esteban Mayoral Campos, Adolfo Muñoz Berrón and Miguel Ángel Bona San Vicente for their support and collaboration during the development of the project. Funding for open access charge: Universidad de Málaga / CBU

PROCESS FOR BREAKING DOWN THE LTE SIGNAL TO EXTRACT KEY INFORMATION

The increasingly important role of Long Term Evolution (LTE) has increased security concerns among the service providers and end users and made security of the network even more indispensable. The main thrust of this thesis is to investigate if the LTE signal can be broken down in a methodical way to obtain information that would otherwise be private; e.g., the Global Positioning System (GPS) location of the user equipment/base station or identity (ID) of the user. The study made use of signal simulators and software to analyze the LTE signal to develop a method to remove noise, breakdown the LTE signal and extract desired information. From the simulation results, it was possible to extract key information in the downlink like the Downlink Control Information (DCI), Cell-Radio Network Temporary Identifier (C-RNTI) and physical Cell Identity (Cell-ID). This information can be modified to cause service disruptions in the network within a reasonable amount of time and with modest computing resources.Defence Science and Technology Agency, SingaporeApproved for public release; distribution is unlimited

Evaluating the effectiveness of Cooperative/Coordinated Multipoint (CoMP) LTE feature in uplink and downlink transmissions

Shannon demonstrated that the channel capacity depends of the ratio of the received signal power to interference plus noise power (SINR). Inter-cell interference caused by neighbouring base stations (BSs) has been identified as one of the most severe problem towards the deployment of LTE technology as it can significantly deteriorate the performance of cellside User Equipment (UE). However, because of regulatory and radiation restrictions as well as operational costs, signal power may only be increased only up to a certain limit to reduce the interference. The other common radio propagation impairment is multipath. Multipath refers to a scenario where multiple copies of a signal propagate to a receiver using different paths. The paths can be created due to signal reflection, scattering and diffraction. As will be discussed later the effects of multipath contribute little to intercell interference because multipath characteristics such as delay spread are compensated for using cyclic prefixes. In this work, we will limit our scope to interference as it has been identified as the main cause of performance degradation for cell edge users due to the full frequency reuse technique used in LTE. To mitigate interference 3GPP devised options of increasing the capacity in LTEAdvanced Release 12 which include the use of spectral aggregation, employing Multiple Input and Multiple Output (MIMO) Antenna techniques, deploying more base stations and micro and femto cells, increasing the degree of sectorisation and Coordinated Multipoint (CoMP). We are primarily interested in evaluating performance improvements introduced when uplink (UL) and downlink (DL) coordinated/cooperative multipoint (CoMP) is enabled in LTE Advanced Release 12 as a way of reducing interference among sites. The CoMP option of reducing interference does not require deployment of new equipment compared to the other options mentioned above hence network deployment costs are minimal. CoMP in theory is known to reduce interference especially for cell edge users and therefore improves network fairness. With CoMP, multiple points coordinate with each other such that transmission of signals to and from other points do not incur serious interference or the interference can even be exploited as a meaningful signal. In September 2011 work on specifications for CoMP support was started in 3GPP LTEAdvanced as one of the core features in LTE-Advanced Release 11 to improve cell edge user throughput as well as the average network throughput. We set to do field measurements in the evaluation of the effectiveness of CoMP in LTE. 3GPP LTE Release 12 was used and cell edge users' performance was the focus. The network operates in 2330 - 2350 MHz band (Channel 40). From the field measurements, it was demonstrated that the CoMP (Scenario 2) feature indeed effective in improving service quality/user experience/fairness for cell edge users. CoMP inherently improves network capacity. A seven (7) percent throughput was noticed

Kanavien yhdistämistekniikan suorituskyvyn arviointi edistyneissä LTE-järjestelmissä

Carrier Aggregation (CA) is an essential technology component in LTE-Advanced (LTE-A). CA is capable of combining up to five Long Term Evolution (LTE) carriers to be used for multicarrier transmission in both downlink and uplink. CA provides increased throughputs, additional capacity and possibilities for load balancing. This thesis presents the key features of CA. Furthermore, the results from CA performance measurements are analyzed and presented. The measurements were conducted in live network to evaluate the end-user experience. The objective was to determine whether CA is capable of delivering the performance that could be theoretically expected. The performance was measured in LTE-A radio network using 2x20 MHz bandwidth with 2x2 MIMO configuration and Category 6 User Equipment (UE). Only downlink CA was measured, since uplink CA capable UEs were not commercially available. The performance was evaluated with stationary and mobility measurements. The results indicate that CA is capable of providing the expected performance gain. In good radio conditions the maximum downlink throughput is close to the 300 Mbit/s. Furthermore, CA performs well in poor radio conditions. The performance gain can be more than 100 %, if the additional carrier is on an unused band. In CA, a secondary component carrier is configured for the UE, in addition to the primary carrier. The operation is performed in connected state either after connection setup or radio handover. The delay in secondary carrier addition was measured to evaluate the impact on user experience. The results indicate that the secondary carrier addition after connection setup or handover is sufficiently fast, and do not have an impact to the user experience.Kanavien yhdistäminen (engl. Carrier Aggregation) on oleellinen tekniikka edistyneessä Long Term Evolution järjestelmässä. Sen avulla on mahdollista yhdistää enintään viisi LTE taajuutta käytettäväksi monikanavaiseen ala- ja ylälinkin lähetykseen. CA mahdollistaa aiempaa suuremmat siirtonopeudet, lisää verkon kapasiteettia sekä antaa mahdollisuuden kuormanjakoon eri taajuuksien välillä. Tässä työssä esitellään CA:n keskeiset ominaisuudet. Lisäksi CA:n suorituskykymittauksien tulokset on analysoitu ja esitelty. Mittaukset toteutettiin operaattorin tuotantoverkossa, jotta loppukäyttäjän saamaa kokemusta on mahdollista arvioida. Tavoitteena oli selvittää, pystyykö CA tarjoamaan sellaista suorituskykyä, jota voidaan teorian perusteella odottaa. Suorituskykyä mitattiin LTE-radioverkossa käyttäen 2x20 MHz kaistanleveyttä ja 2x2 MIMO:n kokoonpanoa sekä kategorian 6 päätelaitetta. Mittaukset suoritettiin vain alalinkissä, sillä ylälinkin CA-kykyisiä päätelaitteita ei ollut kaupallisesti saatavilla. Suorituskykyä on arvioitu sekä piste- että mobiliteettimittauksilla. Tulokset osoittavat, että CA pystyy tarjoamaan oletetun suorituskyvyn parannuksen. Hyvissä radio olosuhteissa maksimi datanopeus alalinkissä on lähes 300 Mbit/s. Lisäksi CA toimii hyvin myös huonoissa radio-olosuhteissa. Suorituskyvyn parannus voi olla enemmän kuin 100 %, jos lisätty toinen kanava on vähemmän käytetyllä taajuuskaistalla. CA:ssa toissijainen kanava konfiguroidaan päätelaitteelle ensisijaisen lisäksi. Operaatio suoritetaan yhteystilassa joko yhteyden muodostamisen tai solunvaihdon jälkeen. Toissijaisen kanavan lisäämisen aiheuttama viive mitattiin, jotta sen vaikutus käyttökokemukseen voitiin arvioida. Tulokset osoittavat, että toissijaisen kanavan lisääminen yhteyden muodostamisen tai solunvaihdon jälkeen on riittävän nopea operaatio, eikä sillä ole vaikutusta käyttökokemukseen

An Innovative RAN Architecture for Emerging Heterogeneous Networks: The Road to the 5G Era

The global demand for mobile-broadband data services has experienced phenomenal growth over the last few years, driven by the rapid proliferation of smart devices such as smartphones and tablets. This growth is expected to continue unabated as mobile data traffic is predicted to grow anywhere from 20 to 50 times over the next 5 years. Exacerbating the problem is that such unprecedented surge in smartphones usage, which is characterized by frequent short on/off connections and mobility, generates heavy signaling traffic load in the network signaling storms . This consumes a disproportion amount of network resources, compromising network throughput and efficiency, and in extreme cases can cause the Third-Generation (3G) or 4G (long-term evolution (LTE) and LTE-Advanced (LTE-A)) cellular networks to crash. As the conventional approaches of improving the spectral efficiency and/or allocation additional spectrum are fast approaching their theoretical limits, there is a growing consensus that current 3G and 4G (LTE/LTE-A) cellular radio access technologies (RATs) won\u27t be able to meet the anticipated growth in mobile traffic demand. To address these challenges, the wireless industry and standardization bodies have initiated a roadmap for transition from 4G to 5G cellular technology with a key objective to increase capacity by 1000Ã? by 2020 . Even though the technology hasn\u27t been invented yet, the hype around 5G networks has begun to bubble. The emerging consensus is that 5G is not a single technology, but rather a synergistic collection of interworking technical innovations and solutions that collectively address the challenge of traffic growth. The core emerging ingredients that are widely considered the key enabling technologies to realize the envisioned 5G era, listed in the order of importance, are: 1) Heterogeneous networks (HetNets); 2) flexible backhauling; 3) efficient traffic offload techniques; and 4) Self Organizing Networks (SONs). The anticipated solutions delivered by efficient interworking/ integration of these enabling technologies are not simply about throwing more resources and /or spectrum at the challenge. The envisioned solution, however, requires radically different cellular RAN and mobile core architectures that efficiently and cost-effectively deploy and manage radio resources as well as offload mobile traffic from the overloaded core network. The main objective of this thesis is to address the key techno-economics challenges facing the transition from current Fourth-Generation (4G) cellular technology to the 5G era in the context of proposing a novel high-risk revolutionary direction to the design and implementation of the envisioned 5G cellular networks. The ultimate goal is to explore the potential and viability of cost-effectively implementing the 1000x capacity challenge while continuing to provide adequate mobile broadband experience to users. Specifically, this work proposes and devises a novel PON-based HetNet mobile backhaul RAN architecture that: 1) holistically addresses the key techno-economics hurdles facing the implementation of the envisioned 5G cellular technology, specifically, the backhauling and signaling challenges; and 2) enables, for the first time to the best of our knowledge, the support of efficient ground-breaking mobile data and signaling offload techniques, which significantly enhance the performance of both the HetNet-based RAN and LTE-A\u27s core network (Evolved Packet Core (EPC) per 3GPP standard), ensure that core network equipment is used more productively, and moderate the evolving 5G\u27s signaling growth and optimize its impact. To address the backhauling challenge, we propose a cost-effective fiber-based small cell backhaul infrastructure, which leverages existing fibered and powered facilities associated with a PON-based fiber-to-the-Node/Home (FTTN/FTTH)) residential access network. Due to the sharing of existing valuable fiber assets, the proposed PON-based backhaul architecture, in which the small cells are collocated with existing FTTN remote terminals (optical network units (ONUs)), is much more economical than conventional point-to-point (PTP) fiber backhaul designs. A fully distributed ring-based EPON architecture is utilized here as the fiber-based HetNet backhaul. The techno-economics merits of utilizing the proposed PON-based FTTx access HetNet RAN architecture versus that of traditional 4G LTE-A\u27s RAN will be thoroughly examined and quantified. Specifically, we quantify the techno-economics merits of the proposed PON-based HetNet backhaul by comparing its performance versus that of a conventional fiber-based PTP backhaul architecture as a benchmark. It is shown that the purposely selected ring-based PON architecture along with the supporting distributed control plane enable the proposed PON-based FTTx RAN architecture to support several key salient networking features that collectively significantly enhance the overall performance of both the HetNet-based RAN and 4G LTE-A\u27s core (EPC) compared to that of the typical fiber-based PTP backhaul architecture in terms of handoff capability, signaling overhead, overall network throughput and latency, and QoS support. It will also been shown that the proposed HetNet-based RAN architecture is not only capable of providing the typical macro-cell offloading gain (RAN gain) but also can provide ground-breaking EPC offloading gain. The simulation results indicate that the overall capacity of the proposed HetNet scales with the number of deployed small cells, thanks to LTE-A\u27s advanced interference management techniques. For example, if there are 10 deployed outdoor small cells for every macrocell in the network, then the overall capacity will be approximately 10-11x capacity gain over a macro-only network. To reach the 1000x capacity goal, numerous small cells including 3G, 4G, and WiFi (femtos, picos, metros, relays, remote radio heads, distributed antenna systems) need to be deployed indoors and outdoors, at all possible venues (residences and enterprises)