A New Approach to the Design of CMOS Inductorless Common-gate Low-noise Amplifiers

This work proposes a new approach to design a simple and effective LNA reaching very competitive results in 1.2V 65-nm standard CMOS technology. The proposed design uses a transconductance enhancement technique to achieve 2.3 dB of noise figure at the 5 GHz band. The paper exposes the advantages of a reduced number of devices in the circuit and analyses the topology. Simulations with complete technology models and statistical analysis are presented for more precise results

A 1.2 V Low-Noise-Amplifier with Double Feedback for High Gain and Low Noise Figure

Part 19: Electronics: AmplifiersInternational audienceIn this paper we present a balun low noise amplifier (LNA) in which the gain is boosted using a double feedback structure. The circuit is based in a conventional Balun LNA with noise and distortion cancellation. The LNA is based in two basic stages: common-gate (CG) and common-source (CS). We propose to replace the resistors by active loads, which have two inputs that will be used to provide the feedback (in the CG and CS stages). This proposed methodology will boost the gain and reduce the NF. Simulation results, with a 130 nm CMOS technology, show that the gain is 23.8 dB and the NF is less than 1.8 dB. The total power dissipation is only 5.3(since no extra blocks are required), leading to an FOM of 5.7 mW− 1 from a nominal 1.2 supply

A 1.2 V low noise amplifier with double feedback for high gain and low noise figure

Dissertação para obtenção do Grau de Mestre em Engenharia Eletrotécnica e de ComputadoresIn this thesis we present a balun low noise amplifier (LNA) in which the gain is boosted using a double feedback structure. The circuit is based in a Balun LNA with noise and distortion cancellation. The LNA is based in two basic stages: common-gate (CG) and common-source (CS). We propose to replace the resistors by active loads, which have two inputs that will be used to provide the feedback (in the CG and CS stages). This proposed methodology will boost the gain and reduce the NF (Noise Figure). Simulation results, with a 130 nm CMOS technology, show that the gain is 19.65 dB and the NF is less than 2.17 dB. The total power dissipation is only 5 mW (since no extra blocks are required), leading to an FOM (Figure of Merit) of 3.13 mW-1 from a nominal 1.2 supply

Can Hardware Distortion Correlation be Neglected When Analyzing Uplink SE in Massive MIMO?

This paper analyzes how the distortion created by hardware impairments in a multiple-antenna base station affects the uplink spectral efficiency (SE), with focus on Massive MIMO. The distortion is correlated across the antennas, but has been often approximated as uncorrelated to facilitate (tractable) SE analysis. To determine when this approximation is accurate, basic properties of the distortion correlation are first uncovered. Then, we focus on third-order non-linearities and prove analytically and numerically that the correlation can be neglected in the SE analysis when there are many users. In i.i.d. Rayleigh fading with equal signal-to-noise ratios, this occurs when having five users.Comment: 5 pages, 3 figures, IEEE International Workshop on Signal Processing Advances in Wireless Communications (SPAWC), 201

CMOS Wide Tuning Gilbert Mixer with Controllable IF Bandwidth in Upcoming RF Front End for Multi-Band Multi-Standard Applications

The current global system for mobile communications, wireless local area, Bluetooth, and ultra-wideband demands a multi-band/multi-standard RF front end that can access all the available bandwidth specifications. Trade-offs occur between power consumption, noise figure, and linearity in CMOS Gilbert mixer wide tuning designs. Besides, it is preferable to have a constant IF bandwidth for different gain settings as the bandwidth varies with the load impedance when an RF receiver is tuned to a higher frequency. My dissertation consists of three parts. First, a tunable constant IF bandwidth Gilbert mixer is introduced for multi-band standard wireless applications such as 802.11 a/b/g WLAN and 802.16a WMAN, followed by a design synthesis approach to optimize the mixer to meet the design center frequency range, constant IF bandwidth, and power. A synthesized Gilbert mixer with effective prototype inductors, designed in 180 nm CMOS process, is presented in this dissertation with the tunability of 200 MHz IF, a constant IF bandwidth of 50 MHz, a conversion gain of 13.75 dB, a noise figure of 2.9dB, 1-dB compression point of -15.19 dBm, IIP3 of -5.8 dBm, and a power of 9 mW. Next, mixer inductor loss and equivalent electronic circuit analysis are presented to optimize the approach to offset center frequency and bandwidth inaccuracy due to the inductance loss between the actual and ideal prototype inductor. The proposed tunable Gilbert mixer simulations present a tunable IF of 177.8 MHz, an IF bandwidth of 87.57 MHz, a conversion gain of 7.4 dB, a noise figure of 3.14 dB, 1-dB compression point of -17.1 dBm, and IIP3 of -19.8 dBm. Last, a CMOS integrated wide frequency span CMOS low noise amplifier is integrated with the tunable Gilbert mixer to achieve a 27.68 dB conversion gain, a 3.47 dB low noise figure, -14.6 dBm 1-dB compression point, and -18.6 dBm IIP3

A MOSFET-only wideband LNA exploiting thermal noise canceling and gain optimization

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para a obtenção do grau de Mestre em Engenharia Electrotécnica e de ComputadoresIn this thesis a MOSFET-only implementation of a balun LNA is presended. This LNA is based on the combination of a common-gate and a common-source stage with canceling of the noise of the common-gate stage. In this circuit, resistors are replaced by transistors, to reduce area and cost, and minimize the e ect of process and supply variations and mismatches. In addition we obtain a higher gain for the same voltage drop. Thus, the LNA gain is optimized, and the noise gure(NF) is reduced. We derive equations for the gain, input matching, and NF. The performance of this new topology is compared with that of a conventional LNA with resistors. Simulation results with a 130 nm CMOS technology show that we obtain a balun LNA with a peak 20.2 dB gain (about 2 dB improvement), and a spot NF lower than 2.4 dB. The total power consumption is only 4.8 mW for a bandwidth wide than 5 GHz

Frequency Translation loops for RF filtering-Theory and Design

Modern wireless transceivers are required to operate over a wide range of frequencies in order to support the multitude of currently available wireless standards. Wideband operation also enables future systems that aim for better utilization of the available spectrum through dynamic allocation. As such, co-existence problems like harmonic mixing and phase noise become a main concern. In particular, dealing with interfer- ence scenarios is crucial since they directly translate to higher linearity requirements in a receiver. With CMOS driving the consumer electronics market due to low cost and high level of integration demands, the continued increase in speed, mainly intended for digital applications, oers new possibilities for RF design to improve the linearity of front-end receivers. Furthermore, the readily available switches in CMOS have proven to be a viable alternative to traditional active mixers for frequency translation due to their high linearity, low flicker noise, and, most recently recognized, their impedance transformation properties. In this thesis, frequency translation feedback loops employing passive mixers are explored as a means to relax the linearity requirements in a front-end receiver by providing channel selectivity as early as possible in the receiver chain. The proposed receiver architecture employing such loop addresses some of the most common prob- lems of integrated RF lters, while maintaining their inherent tunability. Through a simplied and intuitive analysis, the operation of the receiver is first examined and the design parameters aecting the lter characteristics, such as band- width and stop-band rejection, are determined. A systematic procedure for analyzing the linearity of the receiver reveals the possibility of LNA distortion canceling, which decouples the trade-o between noise, linearity and harmonic radiation. Next, a detailed analysis of frequency translation loops using passive mixers is developed. Only highly simplied analysis of such loops is commonly available in literature. The analysis is based on an iterative procedure to address the complexity introduced by the presence of LO harmonics in the loop and the lack of reverse isolation in the mixers, and results in highly accurate expressions for the harmonic and noise transfer functions of the system. Compared to the alternative of applying general LPTV theory, the procedure developed oers more intuition into the operation of the system and only requires the knowledge of basic Fourier analysis. The solution is shown to be capable of predicting trade-os arising due to harmonic mixing and loop stability requirements, and is therefore useful for both system design and optimization. Finally, as a proof of concept, a chip prototype is designed in a standard 65nm CMOS process. The design occupies +12dBm. As such, the work presented in this thesis aims to provide a highly-integrated means for programmable RF channel selection in wideband receivers. The topic oers several possibilities for further research, either in terms of extending the viability of the system, for example by providing higher order ltering, or by improving performance, such as noise

Design of broadband inductor-less RF front-ends with high dynamic range for G.hn

System-on-Chip (SoC) was adopted in recent years as one of the solutions to reduce the cost of integrated systems. When the SoC solution started to be used, the final product was actually more expensive due to lower yield. The developments in integrated technology through the years allowed the integration of more components in lesser area with a better yield. Thus, SoCs became a widely used solution to reduced the cost of the final product, integrating into a single-chip the main parts of a system: analog, digital and memory. As integrated technology kept scaling down to allow a higher density of transistors and thus providing more functionality with the same die area, the analog RF parts of the SoC became a bottleneck to cost reduction as inductors occupy a large die area and do not scale down with technology. Hence, the trend moves toward the research and design of inductor-less SoCs that further reduce the cost of the final solution. Also, as the demand for home networking high-data-rates communication systems has increased over the last decade, several standards have been developed to satisfy the requirements of each application, the most popular being wireless local area networks (WLANs) based on the IEEE 802.11 standard. However, poor signal propagation across walls make WLANs unsuitable for high-speed applications such as high-definition in-home video streaming, leading to the development of wired technologies using the existing in-home infrastructure. The ITU-T G.hn recommendation (G.9960 and G.9961) unifies the most widely used wired infrastructures at home (coaxial cables, phone lines and power lines) into a single standard for high-speed data transmission of up to 1 Gb/s. The G.hn recommendation defines a unified networking over power lines, phone lines and coaxial cables with different plans for baseband and RF. The RF-coax bandplan, where this thesis is focused, uses 50 MHz and 100 MHz bandwidth channels with 256 and 512 carriers respectively. The center frequency can range from 350 MHz to 2450 MHz. The recommendation specifies a transmission power limit of 5 dBm for the 50 MHz bandplan and 8~dBm for the 100 MHz bandplan, therefore the maximum transmitted power in each carrier is the same for both bandplans. Due to the nature of an in-home wired environment, receivers that can handle both very large and very small amplitude signals are required; when transmitter and receiver are connected on the same electric outlet there is no channel attenuation and the signal-to-noise-plus-distortion ratio (SNDR) is dominated by the receiver linearity, whereas when transmitter and receiver are several rooms apart channel attenuation is high and the SNDR is dominated by the receiver noise figure. The high dynamic range specifications for these receivers require the use of configurable-gain topologies that can provide both high-linearity and low-noise for different configurations. Thus, this thesis has been aimed at researching high dynamic range broadband inductor-less topologies to be used as the RF front-end for a G.hn receiver complying with the provided specifications. A large part of the thesis has been focused on the design of the input amplifier of the front-end, which is the most critical stage as the noise figure and linearity of the input amplifier define the achievable overall specifications of the whole front-end. Three prototypes has been manufactured using a 65 nm CMOS process: two input RFPGAs and one front-end using the second RFPGA prototype.El "sistema en un chip" (SoC) fue adoptado recientemente como una de las soluciones para reducir el coste de sistemas integrados. Cuando se empezó a utilizar la solución SoC, el producto final era más caro debido al bajo rendimiento de producción. Los avances en tecnología integrada a lo largo de los años han permitido la integración de más componentes en menos área con mejoras en rendimiento. Por lo tanto, SoCs pasó a ser una solución ampliamente utilizada para reducir el coste del producto final, integrando en un único chip las principales partes de un sistema: analógica, digital y memoria. A medida que las tecnologías integradas se reducían en tamaño para permitir una mayor densisdad de transistores y proveer mayor funcionalidad con la misma área, las partes RF analógicas del SoC pasaron a ser la limitación en la reducción de costes ya que los inductores ocupan mucha área y no escalan con la tecnología. Por lo tanto, las tendencias en investigación se mueven hacia el diseño de SoCs sin inductores que todavía reducen más el coste final del producto. También, a medida que la demanda en sistemas de comunicación domésticos de alta velocidad ha crecido a lo largo de la última década, se han desarrollado varios estándares para satisfacer los requisitos de cada aplicación, siendo las redes sin hilos (WLANs) basadas en el estándar IEEE 802.11 las más populares. Sin embargo, una pobre propagación de señal a través de las paredes hacen que las WLANs sean inadecuadas para aplicaciones de alta-velocidad como transmisión de vídeo de alta definición en tiempo real, resultando en el desarrollo de tecnologías con hilos utilizando la infraestructura existente en los domicilios. La recomendación ITU-T G.hn (G.9960 and G.9961) unifica las principales infraestructuras con hilos domésticas (cables coaxiales, línias de teléfono y línias de electricidad) en un sólo estándar para la transmisión de datos hasta 1 Gb/s. La recomendación G.hn define una red unificada sobre línias de electricidad, de teléfono y coaxiales con diferentes esquemas para banda base y RF. El esquema RF-coax en el cual se basa esta tesis, usa canales con un ancho de banda de 50 MHz y 100 MHz con 256 y 512 portadoras respectivamente. La frecuencia centra puede variar desde 350 MHz hasta 2450 MHz. La recomendación especifica un límite en la potencia de transmisión de 5 dBm para el esquema de 50 MHz y 8 dBm para el esquema de 100 MHz, de tal forma que la potencia máxima por portadora es la misma en ambos esquemas. Debido a la estructura de un entorno doméstico con hilos, los receptores deben ser capaces de procesar señales con amplitud muy grande o muy pequeña; cuando transmisor y receptor están conectados en la misma toma eléctrica no hay atenuación de canal y el ratio de señal a rudio más distorsión (SNDR) está dominado por la linealidad del receptor, mientras que cuando transmisor y receptor están separados por varias habitaciones la atenuación es elevada y el SNDR está dominado por la figura de ruido del receptor. Los elevados requisitos de rango dinámico para este tipo de receptores requieren el uso de topologías de ganancia configurable que pueden proporcionar tanto alta linealidad como bajo ruido para diferentes configuraciones. Por lo tanto, esta tesis está encarada a la investigación de topologías sin inductores de banda ancha y elevado rango dinámico para ser usadas a la entrada de un receptor G.hn cumpliendo con las especificaciones proporcionadas. Una gran parte de la tesis se ha centrado en el diseño del amplificador de entrada al ser la etapa más crítica, ya que la figura de ruido y linealidad del amplificador de entrada definen lás máximas especificaciones que el sistema puede conseguir. Se han fabricado 3 prototipos con un proceso CMOS de 65 nm: 2 amplificadores y un sistema completo con amplificador y mezclador.Postprint (published version

A Fully Integrated 24-GHz Eight-Element Phased-Array Receiver in Silicon

This paper reports the first fully integrated 24-GHz eight-element phased-array receiver in a SiGe BiCMOS technology. The receiver utilizes a heterodyne topology and the signal combining is performed at an IF of 4.8 GHz. The phase-shifting with 4 bits of resolution is realized at the LO port of the first down-conversion mixer. A ring LC voltage-controlled oscillator (VCO) generates 16 different phases of the LO. An integrated 19.2-GHz frequency synthesizer locks the VCO frequency to a 75-MHz external reference. Each signal path achieves a gain of 43 dB, a noise figure of 7.4 dB, and an IIP3 of -11 dBm. The eight-path array achieves an array gain of 61 dB and a peak-to-null ratio of 20 dB and improves the signal-to-noise ratio at the output by 9 dB