Compressed Sensing based Dynamic PSD Map Construction in Cognitive Radio Networks

In the context of spectrum sensing in cognitive radio networks, collaborative spectrum sensing has been proposed as a way to overcome multipath and shadowing, and hence increasing the reliability of the sensing. Due to the high amount of information to be transmitted, a dynamic compressive sensing approach is proposed to map the PSD estimate to a sparse domain which is then transmitted to the fusion center. In this regard, CRs send a compressed version of their estimated PSD to the fusion center, whose job is to reconstruct the PSD estimates of the CRs, fuse them, and make a global decision on the availability of the spectrum in space and frequency domains at a given time. The proposed compressive sensing based method considers the dynamic nature of the PSD map, and uses this dynamicity in order to decrease the amount of data needed to be transmitted between CR sensors’ and the fusion center. By using the proposed method, an acceptable PSD map for cognitive radio purposes can be achieved by only 20 % of full data transmission between sensors and master node. Also, simulation results show the robustness of the proposed method against the channel variations, diverse compression ratios and processing times in comparison with static methods

A Software-Defined Channel Sounder for Industrial Environments with Fast Time Variance

Novel industrial wireless applications require wideband, real-time channel characterization due to complex multipath propagation. Rapid machine motion leads to fast time variance of the channel's reflective behavior, which must be captured for radio channel characterization. Additionally, inhomogeneous radio channels demand highly flexible measurements. Existing approaches for radio channel measurements either lack flexibility or wide-band, real-time performance with fast time variance. In this paper, we propose a correlative channel sounding approach utilizing a software-defined architecture. The approach enables real-time, wide-band measurements with fast time variance immune to active interference. The desired performance is validated with a demanding industrial application example.Comment: Submitted to the 15th International Symposium on Wireless Communication Systems (ISWCS 2018

An indoor variance-based localization technique utilizing the UWB estimation of geometrical propagation parameters

A novel localization framework is presented based on ultra-wideband (UWB) channel sounding, employing a triangulation method using the geometrical properties of propagation paths, such as time delay of arrival, angle of departure, angle of arrival, and their estimated variances. In order to extract these parameters from the UWB sounding data, an extension to the high-resolution RiMAX algorithm was developed, facilitating the analysis of these frequency-dependent multipath parameters. This framework was then tested by performing indoor measurements with a vector network analyzer and virtual antenna arrays. The estimated means and variances of these geometrical parameters were utilized to generate multiple sample sets of input values for our localization framework. Next to that, we consider the existence of multiple possible target locations, which were subsequently clustered using a Kim-Parks algorithm, resulting in a more robust estimation of each target node. Measurements reveal that our newly proposed technique achieves an average accuracy of 0.26, 0.28, and 0.90 m in line-of-sight (LoS), obstructed-LoS, and non-LoS scenarios, respectively, and this with only one single beacon node. Moreover, utilizing the estimated variances of the multipath parameters proved to enhance the location estimation significantly compared to only utilizing their estimated mean values

Contribution to Efficient Use of Narrowband Radio Channel

Předkládaná práce se soustředí na problematiku využívání úzkopásmového rádiového kanálu rádiovými modemy, které jsou určené pro průmyslové aplikace pozemní pohyblivé rádiové služby, specifikované v dominantní míře Evropským standardem ETSI EN 300 113. Tato rádiová zařízení se používají v kmitočtových pásmech od 30 MHz do 1 GHz s nejčastěji přidělovanou šířkou pásma 25 kHz a ve většině svých instalací jsou využívána ve fixních nebo mobilních bezdrátových sítích. Mezi typické oblasti použití patří zejména datová telemetrie, aplikace typu SCADA, nebo monitorování transportu strategických surovin. Za hlavní znaky popisovaného systému lze označit komunikační pokrytí značných vzdáleností, dané především vysokou výkonovou účinnosti datového přenosu a využívaní efektivních přístupových technik na rádiový kanál se semiduplexním komunikačním režimem. Striktní požadavky na elektromagnetickou kompatibilitu umožňují těmto zařízením využívat spektrum i v oblastech kmitočtově blízkým jiným komunikačním systémům bez nutnosti vkládání dodatečných ochranných frekvenčních pásem. Úzkopásmové rádiové komunikační systémy, v současnosti používají převážně exponenciální digitální modulace s konstantní modulační obálkou zejména z důvodů velice striktních omezení pro velikost výkonu vyzářeného do sousedního kanálu. Dosahují tak pouze kompromisních hodnot komunikační účinnosti. Úpravy limitů příslušných rádiových parametrů a rychlý rozvoj prostředků číslicového zpracování signálu v nedávné době, dnes umožňují ekonomicky přijatelné využití spektrálně efektivnějších modulačních technik i v těch oblastech, kde je prioritní využívání úzkých rádiových kanálů. Cílem předkládané disertační práce je proto výzkum postupů směřující ke sjednocení výhodných vlastností lineárních a nelineárních modulací v moderní konstrukci úzkopásmového rádiového modemu. Účelem tohoto výzkumu je efektivní a „ekologické“ využívání přidělené části frekvenčního spektra. Mezi hlavní dílčí problémy, jimiž se předkládaná práce zabývá, lze zařadit zejména tyto: Nyquistova modulační filtrace, navrhovaná s ohledem na minimalizaci nežádoucích elektromagnetických interferencí, efektivní číslicové algoritmy frekvenční demodulace a rychlé rámcové a symbolové synchronizace. Součástí práce je dále analýza navrhovaného řešení z pohledu celkové konstrukce programově definovaného rádiového modemu v rovině simulací při vyšetřování robustnosti datového přenosu rádiovým kanálem s bílým Gaussovským šumem nebo kanálem s únikem v důsledku mnohacestného šíření signálu. Závěr práce je pak zaměřen na prezentování výsledků praktické části projektu, v níž byly testovány, měřeny a analyzovány dvě prototypové konstrukce rádiového zařízení. Tato finální část práce obsahuje i praktická doporučení, vedoucí k vyššímu stupni využitelnosti spektrálně efektivnějších komunikačních režimů v oblasti budoucí generace úzkopásmových zařízení pozemní pohyblivé rádiové služby.he industrial narrowband land mobile radio (LMR) devices, as considered in this dissertation project, has been subject to European standard ETSI EN 300 113. The system operates on frequencies between 30 MHz and 1 GHz, with channel separations of up to 25 kHz, and is intended for private, fixed, or mobile, radio packet switching networks. Data telemetry, SCADA, maritime and police radio services; traffic monitoring; gas, water, and electricity producing factories are the typical system applications. Long distance coverage, high power efficiency, and efficient channel access techniques in half duplex operation are the primary advantages the system relays on. Very low level of adjacent channel power emissions and robust radio receiver architectures, with high dynamic range, enable for a system’s coexistence with various communication standards, without the additional guard band frequency intervals. On the other hand, the strict limitations of the referenced standard as well as the state of the technology, has hindered the increase in communication efficiency, with which the system has used its occupied bandwidth. New modifications and improvements are needed to the standard itself and to the up-to-date architectures of narrowband LMR devices, to make the utilization of more efficient modes of system operation practically realizable. The main objective of this dissertation thesis is therefore to find a practical way how to combine the favorable properties of the advanced nonlinear and linear digital modulation techniques in a single digital modem solution, in order to increase the efficiency of the narrowband radio channel usage allocated to the new generation of the industrial LMR devices. The main attention is given to the particular areas of digital modem design such as proposal of the new family of the Nyquist filters minimizing the adjacent channel interference, design and analysis of the efficient algorithms for frequency discrimination, fast frame and symbol

Dispersive Fourier Transformation for Versatile Microwave Photonics Applications

Abstract: Dispersive Fourier transformation (DFT) maps the broadband spectrum of an ultrashort optical pulse into a time stretched waveform with its intensity profile mirroring the spectrum using chromatic dispersion. Owing to its capability of continuous pulse-by-pulse spectroscopic measurement and manipulation, DFT has become an emerging technique for ultrafast signal generation and processing, and high-throughput real-time measurements, where the speed of traditional optical instruments falls short. In this paper, the principle and implementation methods of DFT are first introduced and the recent development in employing DFT technique for widespread microwave photonics applications are presented, with emphasis on real-time spectroscopy, microwave arbitrary waveform generation, and microwave spectrum sensing. Finally, possible future research directions for DFT-based microwave photonics techniques are discussed as well

Enhanced Compressive Wideband Frequency Spectrum Sensing for Dynamic Spectrum Access

Wideband spectrum sensing detects the unused spectrum holes for dynamic spectrum access (DSA). Too high sampling rate is the main problem. Compressive sensing (CS) can reconstruct sparse signal with much fewer randomized samples than Nyquist sampling with high probability. Since survey shows that the monitored signal is sparse in frequency domain, CS can deal with the sampling burden. Random samples can be obtained by the analog-to-information converter. Signal recovery can be formulated as an L0 norm minimization and a linear measurement fitting constraint. In DSA, the static spectrum allocation of primary radios means the bounds between different types of primary radios are known in advance. To incorporate this a priori information, we divide the whole spectrum into subsections according to the spectrum allocation policy. In the new optimization model, the minimization of the L2 norm of each subsection is used to encourage the cluster distribution locally, while the L0 norm of the L2 norms is minimized to give sparse distribution globally. Because the L0/L2 optimization is not convex, an iteratively re-weighted L1/L2 optimization is proposed to approximate it. Simulations demonstrate the proposed method outperforms others in accuracy, denoising ability, etc.Comment: 23 pages, 6 figures, 4 table. arXiv admin note: substantial text overlap with arXiv:1005.180

JamLab: Augmenting Sensornet Testbeds with Realistic and Controlled Interference Generation

Radio interference drastically affects the performance of sensor-net communications, leading to packet loss and reduced energy-efficiency. As an increasing number of wireless devices operates on the same ISM frequencies, there is a strong need for understanding and debugging the performance of existing sensornet protocols under interference. Doing so requires a low-cost flexible testbed infrastructure that allows the repeatable generation of a wide range of interference patterns. Unfortunately, to date, existing sensornet testbeds lack such capabilities, and do not permit to study easily the coexistence problems between devices sharing the same frequencies. This paper addresses the current lack of such an infrastructure by using off-the-shelf sensor motes to record and playback interference patterns as well as to generate customizable and repeat-able interference in real-time. We propose and develop JamLab: a low-cost infrastructure to augment existing sensornet testbeds with accurate interference generation while limiting the overhead to a simple upload of the appropriate software. We explain how we tackle the hardware limitations and get an accurate measurement and regeneration of interference, and we experimentally evaluate the accuracy of JamLab with respect to time, space, and intensity. We further use JamLab to characterize the impact of interference on sensornet MAC protocols

The FFX Correlator

We established a new algorithm for correlation process in radio astronomy. This scheme consists of the 1st-stage Fourier Transform as a filter and the 2nd-stage Fourier Transform for spectroscopy. The "FFX" correlator stands for Filter and FX architecture, since the 1st-stage Fourier Transform is performed as a digital filter, and the 2nd-stage Fourier Transform is performed as a conventional FX scheme. We developed the FFX correlator hardware not only for the verification of the FFX scheme algorithm but also for the application to the Atacama Submillimeter Telescope Experiment (ASTE) telescope toward high-dispersion and wideband radio observation at submillimeter wavelengths. In this paper, we present the principle of the FFX correlator and its properties, as well as the evaluation results with the production version.Comment: 20 figure