Multiple and single snapshot compressive beamforming

For a sound field observed on a sensor array, compressive sensing (CS) reconstructs the direction-of-arrival (DOA) of multiple sources using a sparsity constraint. The DOA estimation is posed as an underdetermined problem by expressing the acoustic pressure at each sensor as a phase-lagged superposition of source amplitudes at all hypothetical DOAs. Regularizing with an $\ell_1$-norm constraint renders the problem solvable with convex optimization, and promoting sparsity gives high-resolution DOA maps. Here, the sparse source distribution is derived using maximum a posteriori (MAP) estimates for both single and multiple snapshots. CS does not require inversion of the data covariance matrix and thus works well even for a single snapshot where it gives higher resolution than conventional beamforming. For multiple snapshots, CS outperforms conventional high-resolution methods, even with coherent arrivals and at low signal-to-noise ratio. The superior resolution of CS is demonstrated with vertical array data from the SWellEx96 experiment for coherent multi-paths.Comment: In press Journal of Acoustical Society of Americ

Maximizing the Number of Spatial Nulls with Minimum Sensors

In this paper, we attempt to unify two array processing frameworks viz, Acoustic Vector Sensor (AVS) and two level nested array to enhance the Degrees of Freedom (DoF) significantly beyond the limit that is attained by a Uniform Linear Hydrophone Array (ULA) with specified number of sensors. The major focus is to design a line array architecture which provides high resolution unambiguous bearing estimation with increased number of spatial nulls to mitigate the multiple interferences in a deep ocean scenario. AVS can provide more information about the propagating acoustic field intensity vector by simultaneously measuring the acoustic pressure along with tri-axial particle velocity components. In this work, we have developed Nested AVS array (NAVS) ocean data model to demonstrate the performance enhancement. Conventional and MVDR spatial filters are used as the response function to evaluate the performance of the proposed architecture. Simulation results show significant improvement in performance viz, increase of DoF, and localization of more number of acoustic sources and high resolution bearing estimation with reduced side lobe level

Vector sensors for underwater : acoustic communications

Acoustic vector sensors measure acoustic pressure and directional components separately. A claimed advantage of vector sensors over pressure-only arrays is the directional information in a collocated device, making it an attractive option for size-restricted applications. The employment of vector sensors as a receiver for underwater communications is relatively new, where the inherent directionality, usually related to particle velocity, is used for signal-to-noise gain and intersymbol interference mitigation. The fundamental question is how to use vector sensor directional components to bene t communications, which this work seeks to answer and to which it contributes by performing: analysis of acoustic pressure and particle velocity components; comparison of vector sensor receiver structures exploring beamforming and diversity; quanti cation of adapted receiver structures in distinct acoustic scenarios and using di erent types of vector sensors. Analytic expressions are shown for pressure and particle velocity channels, revealing extreme cases of correlation between vector sensors' components. Based on the correlation hypothesis, receiver structures are tested with simulated and experimental data. In a rst approach, called vector sensor passive time-reversal, we take advantage of the channel diversity provided by the inherent directivity of vector sensors' components. In a second approach named vector sensor beam steering, pressure and particle velocity components are combined, resulting in a steered beam for a speci c direction. At last, a joint beam steering and passive time-reversal is proposed, adapted for vector sensors. Tested with two distinct experimental datasets, where vector sensors are either positioned on the bottom or tied to a vessel, a broad performance comparison shows the potential of each receiver structure. Analysis of results suggests that the beam steering structure is preferable for shorter source-receiver ranges, whereas the passive time-reversal is preferable for longer ranges. Results show that the joint beam steering and passive time-reversal is the best option to reduce communication error with robustness along the range.Sensores vetoriais acústicos (em inglês, acoustic vector sensors) são dispositivos que medem, alem da pressão acústica, a velocidade de partícula. Esta ultima, é uma medida que se refere a um eixo, portando, esta associada a uma direção. Ao combinar pressão acústica com componentes de velocidade de partícula pode-se estimar a direção de uma fonte sonora utilizando apenas um sensor vetorial. Na realidade, \um" sensor vetorial é composto de um sensor de pressão (hidrofone) e um ou mais sensores que medem componentes da velocidade de partícula. Como podemos notar, o aspecto inovador está na medição da velocidade de partícula, dado que os hidrofones já são conhecidos.(...)This PhD thesis was supported by the Brazilian Navy Postgraduate Study Abroad Program Port. 227/MB-14/08/2019

Statistical Nested Sensor Array Signal Processing

Source number detection and direction-of-arrival (DOA) estimation are two major applications of sensor arrays. Both applications are often confined to the use of uniform linear arrays (ULAs), which is expensive and difficult to yield wide aperture. Besides, a ULA with N scalar sensors can resolve at most N − 1 sources. On the other hand, a systematic approach was recently proposed to achieve O(N 2 ) degrees of freedom (DOFs) using O(N) sensors based on a nested array, which is obtained by combining two or more ULAs with successively increased spacing. This dissertation will focus on a fundamental study of statistical signal processing of nested arrays. Five important topics are discussed, extending the existing nested-array strategies to more practical scenarios. Novel signal models and algorithms are proposed. First, based on the linear nested array, we consider the problem for wideband Gaussian sources. To employ the nested array to the wideband case, we propose effective strategies to apply nested-array processing to each frequency component, and combine all the spectral information of various frequencies to conduct the detection and estimation. We then consider the practical scenario with distributed sources, which considers the spreading phenomenon of sources. Next, we investigate the self-calibration problem for perturbed nested arrays, for which existing works require certain modeling assumptions, for example, an exactly known array geometry, including the sensor gain and phase. We propose corresponding robust algorithms to estimate both the model errors and the DOAs. The partial Toeplitz structure of the covariance matrix is employed to estimate the gain errors, and the sparse total least squares is used to deal with the phase error issue. We further propose a new class of nested vector-sensor arrays which is capable of significantly increasing the DOFs. This is not a simple extension of the nested scalar-sensor array. Both the signal model and the signal processing strategies are developed in the multidimensional sense. Based on the analytical results, we consider two main applications: electromagnetic (EM) vector sensors and acoustic vector sensors. Last but not least, in order to make full use of the available limited valuable data, we propose a novel strategy, which is inspired by the jackknifing resampling method. Exploiting numerous iterations of subsets of the whole data set, this strategy greatly improves the results of the existing source number detection and DOA estimation methods

Estimation of DOAs of Acoustic Sources in the Presence of Sensors with Uncertainties

Direction of Arrival (DOA) estimation finds its practical importance in sophisticated video conferencing by audio visual means, locating underwater bodies, removing unwanted interferences from desired signals etc. Some efficient algorithms for DOA estimation are already developed by the researchers . The performance of these algorithms is limited by the fact that the receiving antenna array is affected by some uncertainties like mutual coupling, antenna gain and phase error etc. So considerable attention is there in recent research on this area. In this research work the effect of mutual coupling and the effect of antenna gain and phase error in uniform linear array (ULA) on the direction finding of acoustic sources is studied. Also this effect for different source spacing is compared. For that, estimates of the directions of arrival of all uncorrelated acoustic signals in the presence of unknown mutual coupling has been found using conventional Estimation of Signal Parameters via Rotational Invariance Technique (ESPRIT). Also DOAs are computed after knowing the coupling coefficients so that we can compare the two results. Simulation results have shown the fact that the degradation in performance of the algorithm due to mutual coupling becomes more if the sources become closer to each other. Also we have estimated DOAs in the presence of unknown sensor gain and phase errors and we have compared this results with the results we got by considering ideal array. Finally in this case also the effect of gain and phase error as the source spacing varies has been tested. Simulation results verify that performance degradation is more if the sources become closer

A room acoustics measurement system using non-invasive microphone arrays

This thesis summarises research into adaptive room correction for small rooms and pre-recorded material, for example music of films. A measurement system to predict the sound at a remote location within a room, without a microphone at that location was investigated. This would allow the sound within a room to be adaptively manipulated to ensure that all listeners received optimum sound, therefore increasing their enjoyment. The solution presented used small microphone arrays, mounted on the room's walls. A unique geometry and processing system was designed, incorporating three processing stages, temporal, spatial and spectral. The temporal processing identifies individual reflection arrival times from the recorded data. Spatial processing estimates the angles of arrival of the reflections so that the three-dimensional coordinates of the reflections' origin can be calculated. The spectral processing then estimates the frequency response of the reflection. These estimates allow a mathematical model of the room to be calculated, based on the acoustic measurements made in the actual room. The model can then be used to predict the sound at different locations within the room. A simulated model of a room was produced to allow fast development of algorithms. Measurements in real rooms were then conducted and analysed to verify the theoretical models developed and to aid further development of the system. Results from these measurements and simulations, for each processing stage are presented

3D reconstruction and motion estimation using forward looking sonar

Autonomous Underwater Vehicles (AUVs) are increasingly used in different domains including archaeology, oil and gas industry, coral reef monitoring, harbour’s security, and mine countermeasure missions. As electromagnetic signals do not penetrate underwater environment, GPS signals cannot be used for AUV navigation, and optical cameras have very short range underwater which limits their use in most underwater environments. Motion estimation for AUVs is a critical requirement for successful vehicle recovery and meaningful data collection. Classical inertial sensors, usually used for AUV motion estimation, suffer from large drift error. On the other hand, accurate inertial sensors are very expensive which limits their deployment to costly AUVs. Furthermore, acoustic positioning systems (APS) used for AUV navigation require costly installation and calibration. Moreover, they have poor performance in terms of the inferred resolution. Underwater 3D imaging is another challenge in AUV industry as 3D information is increasingly demanded to accomplish different AUV missions. Different systems have been proposed for underwater 3D imaging, such as planar-array sonar and T-configured 3D sonar. While the former features good resolution in general, it is very expensive and requires huge computational power, the later is cheaper implementation but requires long time for full 3D scan even in short ranges. In this thesis, we aim to tackle AUV motion estimation and underwater 3D imaging by proposing relatively affordable methodologies and study different parameters affecting their performance. We introduce a new motion estimation framework for AUVs which relies on the successive acoustic images to infer AUV ego-motion. Also, we propose an Acoustic Stereo Imaging (ASI) system for underwater 3D reconstruction based on forward looking sonars; the proposed system features cheaper implementation than planar array sonars and solves the delay problem in T configured 3D sonars

Tracking aftershock sequences using empirical matched field processing

Extensive aftershock sequences present a significant problem to seismological data centres attempting to produce near real-time comprehensive seismic event bulletins. An elevated number of events to process and poorer performance of automatic phase association algorithms can lead to large delays in processing and a greatly increased human workload. Global monitoring is often performed using seismic array stations at considerable distances from the events involved. Empirical matched field processing (EMFP) is a narrow-frequency band array signal processing technique that recognizes the inter-sensor phase and amplitude relations associated with wavefronts approaching a sensor array from a given direction. We demonstrate that EMFP, using a template obtained from the first P arrival from the main shock alone, can efficiently detect and identify P arrivals on that array from subsequent events in the aftershock zone with exceptionally few false alarms (signals from other sources). The empirical wavefield template encodes all the narrow-band phase and amplitude relations observed for the main shock signal. These relations are also often robust and repeatable characteristics of signals from nearby events. The EMFP detection statistic compares the phase and amplitude relations at a given time in the incoming data stream with those for the template and is sensitive to very short-duration signals with the required characteristics. Significant deviations from the plane-wavefront model that typically degrade the performance of standard beamforming techniques can enhance signal characterization using EMFP. Waveform correlation techniques typically perform poorly for aftershocks from large earthquakes due to the distances between hypocentres and the wide range of event magnitudes and source mechanisms. EMFP on remote seismic arrays mitigates these difficulties; the narrow-band nature of the procedure makes arrival identification less sensitive to the signals’ temporal form and spectral content. The empirical steering vectors derived for the main shock P arrival can reduce the frequency dependency of the slowness vector estimates. This property helps us to automatically screen out arrivals from outside of the aftershock zone. Standard array processing pipelines could be enhanced by including both plane-wave and empirical matched field steering vectors. This would maintain present capability for the plane-wave steering vectors and provide increased sensitivity and resolution for those sources for which we have empirical calibrations.Tracking aftershock sequences using empirical matched field processingacceptedVersio