The IPS fidelity scale as a guideline to implement Supported Employment

info:eu-repo/semantics/publishe

REDUCING POWER DURING MANUFACTURING TEST USING DIFFERENT ARCHITECTURES

Power during manufacturing test can be several times higher than power consumption in functional mode. Excessive power during test can cause IR drop, over-heating, and early aging of the chips. In this dissertation, three different architectures have been introduced to reduce test power in general cases as well as in certain scenarios, including field test. In the first architecture, scan chains are divided into several segments. Every segment needs a control bit to enable capture in a segment when new faults are detectable on that segment for that pattern. Otherwise, the segment should be disabled to reduce capture power. We group the control bits together into one or more control chains. To address the extra pin(s) required to shift data into the control chain(s) and significant post processing in the first architecture, we explored a second architecture. The second architecture stitches the control bits into the chains they control as EECBs (embedded enable capture bits) in between the segments. This allows an ATPG software tool to automatically generate the appropriate EECB values for each pattern to maintain the fault coverage. This also works in the presence of an on-chip decompressor. The last architecture focuses primarily on the self-test of a device in a 3D stacked IC when an existing FPGA in the stack can be programmed as a tester. We show that the energy expended during test is significantly less than would be required using low power patterns fed by an on-chip decompressor for the same very short scan chains

System-on-Chip Design and Test with Embedded Debug Capabilities

In this project, I started with a System-on-Chip platform with embedded test structures. The baseline platform consisted of a Leon2 CPU, AMBA on-chip bus, and an Advanced Encryption Standard decryption module. The basic objective of this thesis was to use the embedded reconfigurable logic blocks for post-silicon debug and verification. The System-on-Chip platform was designed at the register transistor level and implemented in a 180-nm IBM process. Test logic instrumentation was done with DAFCA (Design Automation for Flexible Chip Architecture) Inc. pre-silicon tools. The design was then synthesized using the Synopsys Design Compiler and placed and routed using Cadence SOC Encounter. Total transistor count is about 3 million, including 1400K transistors for the debug module serving as on chip logic analyzer. Core size of the design is about 4.8mm x 4.8mm and the system is working at 151MHz. Design verification was done with Cadence NCSim. The controllability and observability of internal signals of the design is greatly increased with the help of pre-silicon tools which helps locate bugs and later fix them with the help of post-silicon tools. This helps prevent re-spins on several occasions thus saving millions of dollars. Post-silicon tools have been used to program assertions and triggers and inject numerous personalities into the reconfigurable fabric which has greatly increased the versatility of the circuit

Développement des techniques de test et de diagnostic pour les FPGA hiérarchique de type mesh

The evolution trend of shrinking feature size and increasing complexity in modern electronics is being slowed down due to physical limits that generate numerous imperfections and defects during fabrication steps or projected life time of the chip. Field Programmable Gate Arrays (FPGAs) are used in complex digital systems mainly due to their reconfigurability and shorter time-to-market. To maintain a high reliability of such systems, FPGAs should be tested thoroughly for defects. FPGA architecture optimization for area saving and better signal routability is an ongoing process which directly impacts the overall FPGA testability, hence the reliability. This thesis presents a complete strategy for test and diagnosis of manufacturing defects in mesh-based FPGAs containing a novel multilevel interconnects topology which promises to provide better area and routability. Efficiency of the proposed test schemes is analyzed in terms of test cost, respective fault coverage and diagnostic resolution.L’évolution tendant à réduire la taille et augmenter la complexité des circuits électroniques modernes, est en train de ralentir du fait des limitations technologiques, qui génèrent beaucoup de d’imperfections et de defaults durant la fabrication ou la durée de vie de la puce. Les FPGAs sont utilisés dans les systèmes numériques complexes, essentiellement parce qu’ils sont reconfigurables et rapide à commercialiser. Pour garder une grande fiabilité de tels systèmes, les FPGAs doivent être testés minutieusement pour les defaults. L’optimisation de l’architecture des FPGAs pour l’économie de surface et une meilleure routabilité est un processus continue qui impacte directement la testabilité globale et de ce fait, la fiabilité. Cette thèse présente une stratégie complète pour le test et le diagnostique des defaults de fabrication des “mesh-based FPGA” contenant une nouvelle topologie d’interconnections à plusieurs niveaux, ce qui promet d’apporter une meilleure routabilité. Efficacité des schémas proposes est analysée en termes de temps de test, couverture de faute et résolution de diagnostique

Rapid Prototyping and Functional Verification of Power Efficient AI Processor on FPGA

Prototyping a design on a Field Programmable Gate Array (FPGA) involves different stages such as developing a design, performing synthesis, handling placement and routing and finally generating the programming bit file for the FPGA. After successful completion of the above stages, it is important to functionally verify the design. This thesis addresses the challenges involved in rapid prototyping and functional verification of a low power AI processor provided by the industry partner. This research also addresses the methodology used in generating programming bit file and testing the design. Traditional method of testing a design using RTL level testbench utilises more time and relies on functioning of other components associated with the design. This thesis incorporated a new technique of testing the design using software programs focusing on verification of the functionality of a particular module without depending on the other. This methodology reduced the time for functionality verification for part of the design from approximately 1 month to about 2 weeks. Finally, using the methodology mentioned above, the design was synthesized for two FPGA kits, along with analysing the power consumption of the design. The results show the low power nature of the design as it does not use any external memory resulting in faster Arithmetic Logic Unit (ALU) operations thereby saving time to access the data

FPGA ARCHITECTURE AND VERIFICATION OF BUILT IN SELF-TEST (BIST) FOR 32-BIT ADDER/SUBTRACTER USING DE0-NANO FPGA AND ANALOG DISCOVERY 2 HARDWARE

The integrated circuit (IC) is an integral part of everyday modern technology, and its application is very attractive to hardware and software design engineers because of its versatility, integration, power consumption, cost, and board area reduction. IC is available in various types such as Field Programming Gate Array (FPGA), Application Specific Integrated Circuit (ASIC), System on Chip (SoC) architecture, Digital Signal Processing (DSP), microcontrollers (μC), and many more. With technology demand focused on faster, low power consumption, efficient IC application, design engineers are facing tremendous challenges in developing and testing integrated circuits that guaranty functionality, high fault coverage, and reliability as the transistor technology is shrinking to the point where manufacturing defects of ICs are affecting yield which associates with the increased cost of the part. The competitive IC market is pressuring manufactures of ICs to develop and market IC in a relatively quick turnaround which in return requires design and verification engineers to develop an integrated self-test structure that would ensure fault-free and the quality product is delivered on the market. 70-80% of IC design is spent on verification and testing to ensure high quality and reliability for the enduser. To test complex and sophisticated IC designs, the verification engineers must produce laborious and costly test fixtures which affect the cost of the part on the competitive market. To avoid increasing the part cost due to yield and test time to the end-user and to keep up with the competitive market many IC design engineers are deviating from complex external test fixture approach and are focusing on integrating Built-in Self-Test (BIST) or Design for Test (DFT) techniques onto IC’s which would reduce time to market but still guarantee high coverage for the product. Understanding the BIST, the architecture, as well as the application of IC, must be understood before developing IC. The architecture of FPGA is elaborated in this paper followed by several BIST techniques and applications of those BIST relative to FPGA, SoC, analog to digital (ADC), or digital to analog converters (DAC) that are integrated on IC. Paper is concluded with verification of BIST for the 32-bit adder/subtracter designed in Quartus II software using the Analog Discovery 2 module as stimulus and DE0-NANO FPGA board for verification

Design and Evaluation of a Parameterizable NoC Router for FPGAs

The Network-on-Chip (NoC) approach for designing (System-on-Chip) SoCs is currently emerging as an advanced concept for overcoming the scalability and efficiency problems of traditional on-chip interconnection schemes. This thesis addresses the design and evaluation of a parameterizable NoC router for FPGAs. The importance of low area overhead for NoC components is crucial in FPGAs, which have fixed logic and routing resources. We achieve a low area router design through optimizations in switching fabric and dual purpose buffer/connection signals. We propose a component library to increase re-use and allow tailoring of parameters for application specific NoCs of various sizes. A set of experiments were conducted to explore the design space of the proposed NoC router using different values of key router parameters: channel width (flit size), arbitration scheme and IP-core-to-router mapping strategy. Area and latency results from the experiments are presented and analyzed